以下是代码:
#include <SPI.h>
#include <Ethernet.h>
#include <Wire.h>
#include <math.h>
#include <Servo.h>
//QQqun:51798659 XiaoHe此代码是用以太网连接yeelink平台实现点亮一个led,访问http://api.yeelink.net/v1.1/device/357111/sensor/555555/datapoints/后面提交的是key来获取一个网页信息,然后再加以提出需要的判断
Servo myservo; // create servo object to control a servo
// a maximum of eight servo objects can be created
int pos = 0; // variable to store the servo position
byte buff[2];
int led=5;//led脚
// for yeelink api
#define APIKEY "c2a4877a26b7bd000872227c60b67406" // 此处替换为你自己的API KEY
#define DEVICEID 35740 // 此处替换为你的设备编号
#define SENSORID 40555 // 此处替换为你的传感器编号
char pd='v'; //写的一个字符判断
// assign a MAC address for the ethernet controller.
byte mac[] = { 0x00, 0x1D, 0x72, 0x82, 0x35, 0x9D};
// initialize the library instance:
EthernetClient client ;
char server[] = "api.yeelink.net"; // 连接 的服务器地址
unsigned long lastConnectionTime = 0; // last time you connected to the server, in milliseconds
boolean lastConnected = false; // state of the connection last time through the main loop
const unsigned long postingInterval = 1*1000; // delay between 2 datapoints, 延时多少秒访问一次
String returnValue = "";
boolean ResponseBegin = false;
void setup() {
pinMode(5, OUTPUT);
Wire.begin();
// start serial port:
Serial.begin(115200);
myservo.attach(9); // attaches the servo on pin 9 to the servo object
// start the Ethernet connection with DHCP:
if (Ethernet.begin(mac) == 0) {
Serial.println("Failed to configure Ethernet using DHCP");
for(;;)
;
}
else {
Serial.println("Ethernet configuration OK");
}
}
void loop() {
// if there's incoming data from the net connection.
// send it out the serial port. This is for debugging
// purposes only:
if (client.available()) {
char c = client.read();
// Serial.print(c);
if (c == '{')
ResponseBegin = true;
else if (c == '}')
ResponseBegin = false;
if (ResponseBegin)
returnValue += c;
}
if (returnValue.length() !=0 && (ResponseBegin == false))
{
Serial.println(returnValue);//打印出接收的数据
pd=returnValue.charAt(9);//取第几位字符
Serial.print("Jie Shou de zifu:");//串口方便好看
Serial.println(pd);
if (pd == '1') {
Serial.println("turn ON ON ON ON the LED");
digitalWrite(led, HIGH);
for(pos = 0; pos <180; pos += 1) // goes from 0 degrees to 180 degrees
{ // in steps of 1 degree
myservo.write(180); // tell servo to go to position in variable 'pos'
delay(10); // waits 15ms for the servo to reach the position
}
for(pos = 180; pos>=1; pos-=1) // goes from 180 degrees to 0 degrees
{
myservo.write(0); // tell servo to go to position in variable 'pos'
delay(10); // waits 15ms for the servo to reach the position
}
}
else if(pd== '0') {
Serial.println("turn off off off the LED_____________");
digitalWrite(led, LOW);
}
returnValue = "";
}
// if there's no net connection, but there was one last time
// through the loop, then stop the client:
if (!client.connected() && lastConnected) {
Serial.println();
Serial.println("disconnecting.");
client.stop();
}
// if you're not connected, and ten seconds have passed since
// your last connection, then connect again and send data:
if(!client.connected() && (millis() - lastConnectionTime > postingInterval)) {
// read sensor data, replace with your code
//int sensorReading = readLightSensor();
Serial.print("yeelink:");
//get data from server
getData();
}
// store the state of the connection for next time through
// the loop:
lastConnected = client.connected();
}
// this method makes a HTTP connection to the server and get data back
void getData(void) {
// if there's a successful connection:
if (client.connect(server, 80)) {
Serial.println("connecting...");
// send the HTTP GET request:
client.print("GET /v1.1/device/");
client.print(DEVICEID);
client.print("/sensor/");
client.print(SENSORID);
client.print("/datapoints");
client.println(" HTTP/1.1");
client.println("Host: api.yeelink.net");
client.print("Accept: *");
client.print("/");
client.println("*");
client.print("U-ApiKey: ");
client.println(APIKEY);
client.println("Content-Length: 0");
client.println("Connection: close");
client.println();
Serial.println("print get done.");
}
else {
// if you couldn't make a connection:
Serial.println("connection failed");
Serial.println();
Serial.println("disconnecting.");
client.stop();
}
// note the time that the connection was made or attempted:
lastConnectionTime = millis();
}