问题原因:由于在开机后设置了定时时间关机,关机后INT脚电平一直在,导致相当POWER脚一直有按下,不能开机(RTC 电池的存在,INT一直为低),系统上电开机,需要在uboot阶段清中断。
Dts 配置:具体挂在哪路i2c 上,需要结合硬件原理图。
&i2c3 {
status = "okay";
hym8563: hym8563@51 {
status = "okay";
compatible = "haoyu,hym8563";
reg = <0x51>;
#clock-cells = <0>;
};
};
kernel 阶段:
/*
* Haoyu HYM8563 RTC driver
*
* Copyright (C) 2013 MundoReader S.L.
* Author: Heiko Stuebner <heiko@sntech.de>
*
* based on rtc-HYM8563
* Copyright (C) 2010 ROCKCHIP, Inc.
*
* This software is licensed under the terms of the GNU General Public
* License version 2, as published by the Free Software Foundation, and
* may be copied, distributed, and modified under those terms.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*/
#include <linux/module.h>
#include <linux/clk-provider.h>
#include <linux/i2c.h>
#include <linux/bcd.h>
#include <linux/rtc.h>
#define HYM8563_CTL1 0x00
#define HYM8563_CTL1_TEST BIT(7)
#define HYM8563_CTL1_STOP BIT(5)
#define HYM8563_CTL1_TESTC BIT(3)
#define HYM8563_CTL2 0x01
#define HYM8563_CTL2_TI_TP BIT(4)
#define HYM8563_CTL2_AF BIT(3)
#define HYM8563_CTL2_TF BIT(2)
#define HYM8563_CTL2_AIE BIT(1)
#define HYM8563_CTL2_TIE BIT(0)
#define HYM8563_SEC 0x02
#define HYM8563_SEC_VL BIT(7)
#define HYM8563_SEC_MASK 0x7f
#define HYM8563_MIN 0x03
#define HYM8563_MIN_MASK 0x7f
#define HYM8563_HOUR 0x04
#define HYM8563_HOUR_MASK 0x3f
#define HYM8563_DAY 0x05
#define HYM8563_DAY_MASK 0x3f
#define HYM8563_WEEKDAY 0x06
#define HYM8563_WEEKDAY_MASK 0x07
#define HYM8563_MONTH 0x07
#define HYM8563_MONTH_CENTURY BIT(7)
#define HYM8563_MONTH_MASK 0x1f
#define HYM8563_YEAR 0x08
#define HYM8563_ALM_MIN 0x09
#define HYM8563_ALM_HOUR 0x0a
#define HYM8563_ALM_DAY 0x0b
#define HYM8563_ALM_WEEK 0x0c
/* Each alarm check can be disabled by setting this bit in the register */
#define HYM8563_ALM_BIT_DISABLE BIT(7)
#define HYM8563_CLKOUT 0x0d
#define HYM8563_CLKOUT_ENABLE BIT(7)
#define HYM8563_CLKOUT_32768 0
#define HYM8563_CLKOUT_1024 1
#define HYM8563_CLKOUT_32 2
#define HYM8563_CLKOUT_1 3
#define HYM8563_CLKOUT_MASK 3
#define HYM8563_TMR_CTL 0x0e
#define HYM8563_TMR_CTL_ENABLE BIT(7)
#define HYM8563_TMR_CTL_4096 0
#define HYM8563_TMR_CTL_64 1
#define HYM8563_TMR_CTL_1 2
#define HYM8563_TMR_CTL_1_60 3
#define HYM8563_TMR_CTL_MASK 3
#define HYM8563_TMR_CNT 0x0f
struct hym8563 {
struct i2c_client *client;
struct rtc_device *rtc;
#ifdef CONFIG_COMMON_CLK
struct clk_hw clkout_hw;
#endif
};
struct hym8563_priv {
struct i2c_client *client;
unsigned char rtc_int_enable;
unsigned char buf[4];
};
struct hym8563_priv g_hym8563 = {
.client = 0,
};
/*
* RTC handling
*/
static int hym8563_rtc_read_time(struct device *dev, struct rtc_time *tm)
{
struct i2c_client *client = to_i2c_client(dev);
u8 buf[7];
int ret;
ret = i2c_smbus_read_i2c_block_data(client, HYM8563_SEC, 7, buf);
tm->tm_sec = bcd2bin(buf[0] & HYM8563_SEC_MASK);
tm->tm_min = bcd2bin(buf[1] & HYM8563_MIN_MASK);
tm->tm_hour = bcd2bin(buf[2] & HYM8563_HOUR_MASK);
tm->tm_mday = bcd2bin(buf[3] & HYM8563_DAY_MASK);
tm->tm_wday = bcd2bin(buf[4] & HYM8563_WEEKDAY_MASK); /* 0 = Sun */
tm->tm_mon = bcd2bin(buf[5] & HYM8563_MONTH_MASK) - 1; /* 0 = Jan */
tm->tm_year = bcd2bin(buf[6]) + 100;
return 0;
}
static int hym8563_rtc_set_time(struct device *dev, struct rtc_time *tm)
{
struct i2c_client *client = to_i2c_client(dev);
u8 buf[7];
int ret;
/* Years >= 2100 are to far in the future, 19XX is to early */
if (tm->tm_year < 100 || tm->tm_year >= 200)
return -EINVAL;
buf[0] = bin2bcd(tm->tm_sec);
buf[1] = bin2bcd(tm->tm_min);
buf[2] = bin2bcd(tm->tm_hour);
buf[3] = bin2bcd(tm->tm_mday);
buf[4] = bin2bcd(tm->tm_wday);
buf[5] = bin2bcd(tm->tm_mon + 1);
/*
* While the HYM8563 has a century flag in the month register,
* it does not seem to carry it over a subsequent write/read.
* So we'll limit ourself to 100 years, starting at 2000 for now.
*/
buf[6] = bin2bcd(tm->tm_year - 100);
/*
* CTL1 only contains TEST-mode bits apart from stop,
* so no need to read the value first
*/
ret = i2c_smbus_write_byte_data(client, HYM8563_CTL1,
HYM8563_CTL1_STOP);
if (ret < 0)
return ret;
ret = i2c_smbus_write_i2c_block_data(client, HYM8563_SEC, 7, buf);
if (ret < 0)
return ret;
ret = i2c_smbus_write_byte_data(client, HYM8563_CTL1, 0);
if (ret < 0)
return ret;
return 0;
}
static int hym8563_rtc_alarm_irq_enable(struct device *dev,
unsigned int enabled)
{
struct i2c_client *client = to_i2c_client(dev);
int data;
data = i2c_smbus_read_byte_data(client, HYM8563_CTL2);
if (data < 0)
return data;
if (enabled)
data |= HYM8563_CTL2_AIE;
else
data &= ~HYM8563_CTL2_AIE;
return i2c_smbus_write_byte_data(client, HYM8563_CTL2, data);
};
static int hym8563_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alm)
{
struct i2c_client *client = to_i2c_client(dev);
struct rtc_time *alm_tm = &alm->time;
u8 buf[4];
int ret;
ret = i2c_smbus_read_i2c_block_data(client, HYM8563_ALM_MIN, 4, buf);
if (ret < 0)
return ret;
/* The alarm only has a minute accuracy */
alm_tm->tm_sec = 0;
alm_tm->tm_min = (buf[0] & HYM8563_ALM_BIT_DISABLE) ?
-1 :
bcd2bin(buf[0] & HYM8563_MIN_MASK);
alm_tm->tm_hour = (buf[1] & HYM8563_ALM_BIT_DISABLE) ?
-1 :
bcd2bin(buf[1] & HYM8563_HOUR_MASK);
alm_tm->tm_mday = (buf[2] & HYM8563_ALM_BIT_DISABLE) ?
-1 :
bcd2bin(buf[2] & HYM8563_DAY_MASK);
alm_tm->tm_wday = (buf[3] & HYM8563_ALM_BIT_DISABLE) ?
-1 :
bcd2bin(buf[3] & HYM8563_WEEKDAY_MASK);
ret = i2c_smbus_read_byte_data(client, HYM8563_CTL2);
if (ret < 0)
return ret;
if (ret & HYM8563_CTL2_AIE)
alm->enabled = 1;
return 0;
}
static int hym8563_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alm)
{
struct i2c_client *client = to_i2c_client(dev);
struct rtc_time *alm_tm = &alm->time;
u8 buf[4];
int ret;
/*
* The alarm has no seconds so deal with it
*/
if (alm_tm->tm_sec) {
alm_tm->tm_sec = 0;
alm_tm->tm_min++;
if (alm_tm->tm_min >= 60) {
alm_tm->tm_min = 0;
alm_tm->tm_hour++;
if (alm_tm->tm_hour >= 24) {
alm_tm->tm_hour = 0;
alm_tm->tm_mday++;
alm_tm->tm_wday++;
if (alm_tm->tm_wday > 6)
alm_tm->tm_wday = 0;
switch (alm_tm->tm_mon + 1) {
case 1:
case 3:
case 5:
case 7:
case 8:
case 10:
case 12:
if (alm_tm->tm_mday > 31)
alm_tm->tm_mday = 1;
break;
case 4:
case 6:
case 9:
case 11:
if (alm_tm->tm_mday > 30)
alm_tm->tm_mday = 1;
break;
case 2:
if (alm_tm->tm_year / 4 == 0) {
if (alm_tm->tm_mday > 29)
alm_tm->tm_mday = 1;
} else if (alm_tm->tm_mday > 28) {
alm_tm->tm_mday = 1;
}
break;
}
}
}
}
printk("%s\n,tm_min=%d,tm_hour=%d,tm_mday=%d,tm_wday=%d,enabled=%d\n",__func__,alm_tm->tm_min,alm_tm->tm_hour,alm_tm->tm_mday,
alm_tm->tm_wday,alm->enabled);
ret = i2c_smbus_read_byte_data(client, HYM8563_CTL2);
if (ret < 0)
return ret;
ret &= ~HYM8563_CTL2_AIE;
//ret |= HYM8563_CTL2_AIE;
ret = i2c_smbus_write_byte_data(client, HYM8563_CTL2, ret);
if (ret < 0)
return ret;
buf[0] = (alm_tm->tm_min < 60 && alm_tm->tm_min >= 0) ?
bin2bcd(alm_tm->tm_min) : HYM8563_ALM_BIT_DISABLE;
buf[1] = (alm_tm->tm_hour < 24 && alm_tm->tm_hour >= 0) ?
bin2bcd(alm_tm->tm_hour) : HYM8563_ALM_BIT_DISABLE;
buf[2] = (alm_tm->tm_mday <= 31 && alm_tm->tm_mday >= 1) ?
bin2bcd(alm_tm->tm_mday) : HYM8563_ALM_BIT_DISABLE;
buf[3] = (alm_tm->tm_wday < 7 && alm_tm->tm_wday >= 0) ?
bin2bcd(alm_tm->tm_wday) : HYM8563_ALM_BIT_DISABLE;
if(alm->enabled)
{
g_hym8563.buf[0] = buf[0];
g_hym8563.buf[1] = buf[1];
g_hym8563.buf[2] = buf[2];
g_hym8563.buf[3] = buf[3];
g_hym8563.rtc_int_enable = 1;
printk("##fan## %s save alarm time\n",__func__);
return 0;
}
ret = i2c_smbus_write_i2c_block_data(client, HYM8563_ALM_MIN, 4, buf);
if (ret < 0)
return ret;
return hym8563_rtc_alarm_irq_enable(dev, alm->enabled);
}
static int hym8563_rtc_alarm_irq_enable1(struct i2c_client *client,
unsigned int enabled)
{
int data;
data = i2c_smbus_read_byte_data(client, HYM8563_CTL2);
if (data < 0)
return data;
printk("#### %s ######### enabled=%d before data=%0x \n",__func__,enabled,data);
if (enabled)
data |= HYM8563_CTL2_AIE;
else
data &= ~HYM8563_CTL2_AIE;
data &= ~HYM8563_CTL2_AF;
printk("#### %s ######### enabled=%d after data=%0x \n",__func__,enabled,data);
return i2c_smbus_write_byte_data(client, HYM8563_CTL2, data);
};
void hym8563_system_power_off_set_alarm(void)
{
struct i2c_client *client = g_hym8563.client;
unsigned char buf[4];
int ret;
printk("### %s ######### rtc_int_enable=%d\n",__func__,g_hym8563.rtc_int_enable);
if(g_hym8563.client == 0)
{
printk("#### %s can't find hym8563 i2c client\n",__func__);
return;
}
if(g_hym8563.rtc_int_enable)
{
buf[0] = g_hym8563.buf[0];
buf[1] = g_hym8563.buf[1];
buf[2] = g_hym8563.buf[2];
buf[3] = g_hym8563.buf[3];
ret = i2c_smbus_write_i2c_block_data(client, HYM8563_ALM_MIN, 4, buf);
if(ret < 0)
return;
hym8563_rtc_alarm_irq_enable1(client, !!g_hym8563.rtc_int_enable);
}
}
static const struct rtc_class_ops hym8563_rtc_ops = {
.read_time = hym8563_rtc_read_time,
.set_time = hym8563_rtc_set_time,
.alarm_irq_enable = hym8563_rtc_alarm_irq_enable,
.read_alarm = hym8563_rtc_read_alarm,
.set_alarm = hym8563_rtc_set_alarm,
};
/*
* Handling of the clkout
*/
#ifdef CONFIG_COMMON_CLK
#define clkout_hw_to_hym8563(_hw) container_of(_hw, struct hym8563, clkout_hw)
static int clkout_rates[] = {
32768,
1024,
32,
1,
};
static unsigned long hym8563_clkout_recalc_rate(struct clk_hw *hw,
unsigned long parent_rate)
{
struct hym8563 *hym8563 = clkout_hw_to_hym8563(hw);
struct i2c_client *client = hym8563->client;
int ret = i2c_smbus_read_byte_data(client, HYM8563_CLKOUT);
if (ret < 0)
return 0;
ret &= HYM8563_CLKOUT_MASK;
return clkout_rates[ret];
}
static long hym8563_clkout_round_rate(struct clk_hw *hw, unsigned long rate,
unsigned long *prate)
{
int i;
for (i = 0; i < ARRAY_SIZE(clkout_rates); i++)
if (clkout_rates[i] <= rate)
return clkout_rates[i];
return 0;
}
static int hym8563_clkout_set_rate(struct clk_hw *hw, unsigned long rate,
unsigned long parent_rate)
{
struct hym8563 *hym8563 = clkout_hw_to_hym8563(hw);
struct i2c_client *client = hym8563->client;
int ret = i2c_smbus_read_byte_data(client, HYM8563_CLKOUT);
int i;
if (ret < 0)
return ret;
for (i = 0; i < ARRAY_SIZE(clkout_rates); i++)
if (clkout_rates[i] == rate) {
ret &= ~HYM8563_CLKOUT_MASK;
ret |= i;
return i2c_smbus_write_byte_data(client,
HYM8563_CLKOUT, ret);
}
return -EINVAL;
}
static int hym8563_clkout_control(struct clk_hw *hw, bool enable)
{
struct hym8563 *hym8563 = clkout_hw_to_hym8563(hw);
struct i2c_client *client = hym8563->client;
int ret = i2c_smbus_read_byte_data(client, HYM8563_CLKOUT);
if (ret < 0)
return ret;
if (enable)
ret |= HYM8563_CLKOUT_ENABLE;
else
ret &= ~HYM8563_CLKOUT_ENABLE;
return i2c_smbus_write_byte_data(client, HYM8563_CLKOUT, ret);
}
static int hym8563_clkout_prepare(struct clk_hw *hw)
{
return hym8563_clkout_control(hw, 1);
}
static void hym8563_clkout_unprepare(struct clk_hw *hw)
{
hym8563_clkout_control(hw, 0);
}
static int hym8563_clkout_is_prepared(struct clk_hw *hw)
{
struct hym8563 *hym8563 = clkout_hw_to_hym8563(hw);
struct i2c_client *client = hym8563->client;
int ret = i2c_smbus_read_byte_data(client, HYM8563_CLKOUT);
if (ret < 0)
return ret;
return !!(ret & HYM8563_CLKOUT_ENABLE);
}
static const struct clk_ops hym8563_clkout_ops = {
.prepare = hym8563_clkout_prepare,
.unprepare = hym8563_clkout_unprepare,
.is_prepared = hym8563_clkout_is_prepared,
.recalc_rate = hym8563_clkout_recalc_rate,
.round_rate = hym8563_clkout_round_rate,
.set_rate = hym8563_clkout_set_rate,
};
static struct clk *hym8563_clkout_register_clk(struct hym8563 *hym8563)
{
struct i2c_client *client = hym8563->client;
struct device_node *node = client->dev.of_node;
struct clk *clk;
struct clk_init_data init = {};
int ret;
ret = i2c_smbus_write_byte_data(client, HYM8563_CLKOUT,
0);
if (ret < 0)
return ERR_PTR(ret);
init.name = "hym8563-clkout";
init.ops = &hym8563_clkout_ops;
init.flags = 0;
init.parent_names = NULL;
init.num_parents = 0;
hym8563->clkout_hw.init = &init;
/* optional override of the clockname */
of_property_read_string(node, "clock-output-names", &init.name);
/* register the clock */
clk = clk_register(&client->dev, &hym8563->clkout_hw);
if (!IS_ERR(clk))
of_clk_add_provider(node, of_clk_src_simple_get, clk);
return clk;
}
#endif
/*
* The alarm interrupt is implemented as a level-low interrupt in the
* hym8563, while the timer interrupt uses a falling edge.
* We don't use the timer at all, so the interrupt is requested to
* use the level-low trigger.
*/
static irqreturn_t hym8563_irq(int irq, void *dev_id)
{
struct hym8563 *hym8563 = (struct hym8563 *)dev_id;
struct i2c_client *client = hym8563->client;
struct mutex *lock = &hym8563->rtc->ops_lock;
int data, ret;
mutex_lock(lock);
/* Clear the alarm flag */
data = i2c_smbus_read_byte_data(client, HYM8563_CTL2);
if (data < 0) {
dev_err(&client->dev, "%s: error reading i2c data %d\n",
__func__, data);
goto out;
}
data &= ~HYM8563_CTL2_AF;
ret = i2c_smbus_write_byte_data(client, HYM8563_CTL2, data);
if (ret < 0) {
dev_err(&client->dev, "%s: error writing i2c data %d\n",
__func__, ret);
}
out:
mutex_unlock(lock);
return IRQ_HANDLED;
}
static int hym8563_init_device(struct i2c_client *client)
{
int ret;
int i;
/* Clear stop flag if present */
for(i=0;i<5;i++)
{
ret = i2c_smbus_read_byte_data(client, HYM8563_CTL1);
if(ret>=0)
break;
}
ret = i2c_smbus_write_byte_data(client, HYM8563_CTL1, 0);
if (ret < 0)
return ret;
ret = i2c_smbus_read_byte_data(client, HYM8563_CTL2);
if (ret < 0)
return ret;
/* Disable alarm and timer interrupts */
ret &= ~HYM8563_CTL2_AIE;
ret &= ~HYM8563_CTL2_TIE;
/* Clear any pending alarm and timer flags */
if (ret & HYM8563_CTL2_AF)
ret &= ~HYM8563_CTL2_AF;
if (ret & HYM8563_CTL2_TF)
ret &= ~HYM8563_CTL2_TF;
ret &= ~HYM8563_CTL2_TI_TP;
return i2c_smbus_write_byte_data(client, HYM8563_CTL2, ret);
}
#ifdef CONFIG_PM_SLEEP
static int hym8563_suspend(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
int ret;
if (device_may_wakeup(dev)) {
ret = enable_irq_wake(client->irq);
if (ret) {
dev_err(dev, "enable_irq_wake failed, %d\n", ret);
return ret;
}
}
return 0;
}
static int hym8563_resume(struct device *dev)
{
struct i2c_client *client = to_i2c_client(dev);
if (device_may_wakeup(dev))
disable_irq_wake(client->irq);
return 0;
}
#endif
static SIMPLE_DEV_PM_OPS(hym8563_pm_ops, hym8563_suspend, hym8563_resume);
static int hym8563_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct hym8563 *hym8563;
int ret;
/*
* hym8563 initial time(2021_1_1_12:00:00),
* avoid hym8563 read time error
*/
struct rtc_time tm_read, tm = {
.tm_wday = 0,
.tm_year = 121,
.tm_mon = 0,
.tm_mday = 1,
.tm_hour = 12,
.tm_min = 0,
.tm_sec = 0,
};
g_hym8563.client = client;
g_hym8563.rtc_int_enable = 0;
hym8563 = devm_kzalloc(&client->dev, sizeof(*hym8563), GFP_KERNEL);
if (!hym8563)
return -ENOMEM;
hym8563->client = client;
i2c_set_clientdata(client, hym8563);
ret = hym8563_init_device(client);
if (ret) {
dev_err(&client->dev, "could not init device, %d\n", ret);
return ret;
}
if (client->irq > 0) {
ret = devm_request_threaded_irq(&client->dev, client->irq,
NULL, hym8563_irq,
IRQF_TRIGGER_LOW | IRQF_ONESHOT,
client->name, hym8563);
if (ret < 0) {
dev_err(&client->dev, "irq %d request failed, %d\n",
client->irq, ret);
return ret;
}
}
if (client->irq > 0 ||
device_property_read_bool(&client->dev, "wakeup-source")) {
device_init_wakeup(&client->dev, true);
}
/* check state of calendar information */
ret = i2c_smbus_read_byte_data(client, HYM8563_SEC);
if (ret < 0)
return ret;
dev_info(&client->dev, "rtc information is %s\n",
(ret & HYM8563_SEC_VL) ? "invalid" : "valid");
hym8563_rtc_read_time(&client->dev, &tm_read);
if ((ret & HYM8563_SEC_VL) || (tm_read.tm_year < 70) || (tm_read.tm_year > 200) ||
(tm_read.tm_mon == -1) || (rtc_valid_tm(&tm_read) != 0))
hym8563_rtc_set_time(&client->dev, &tm);
hym8563->rtc = devm_rtc_device_register(&client->dev, client->name,
&hym8563_rtc_ops, THIS_MODULE);
if (IS_ERR(hym8563->rtc))
return PTR_ERR(hym8563->rtc);
/* the hym8563 alarm only supports a minute accuracy */
hym8563->rtc->uie_unsupported = 1;
#ifdef CONFIG_COMMON_CLK
hym8563_clkout_register_clk(hym8563);
#endif
return 0;
}
static const struct i2c_device_id hym8563_id[] = {
{ "hym8563", 0 },
{},
};
MODULE_DEVICE_TABLE(i2c, hym8563_id);
static const struct of_device_id hym8563_dt_idtable[] = {
{ .compatible = "haoyu,hym8563" },
{},
};
MODULE_DEVICE_TABLE(of, hym8563_dt_idtable);
static struct i2c_driver hym8563_driver = {
.driver = {
.name = "rtc-hym8563",
.pm = &hym8563_pm_ops,
.of_match_table = hym8563_dt_idtable,
},
.probe = hym8563_probe,
.id_table = hym8563_id,
};
module_i2c_driver(hym8563_driver);
MODULE_AUTHOR("Heiko Stuebner <heiko@sntech.de>");
MODULE_DESCRIPTION("HYM8563 RTC driver");
MODULE_LICENSE("GPL");
由于在开机后设置了定时时间关机,关机后INT脚电平一直在,导致相当POWER脚一直有按下,不能开机(RTC 电池的存在,INT一直为低),系统上电开机,需要在uboot阶段清中断。
ret &= ~HYM8563_CTL2_AIE;
ret &= ~HYM8563_CTL2_TIE;
/* Clear any pending alarm and timer flags */
if (ret & HYM8563_CTL2_AF)
ret &= ~HYM8563_CTL2_AF;
if (ret & HYM8563_CTL2_TF)
ret &= ~HYM8563_CTL2_TF;
ret &= ~HYM8563_CTL2_TI_TP;
printf_info("#### %s ret=0x%x\n",__func__,ret);
return i2c_write_byte_data(HYM8563_CTL2, ret);
Uboot. 阶段
//
/*
* (C) Copyright 2008-2018 Youngfel Electronics Co., Ltd
*/
#include <common.h>
#include <dm.h>
#include <dm/device-internal.h>
#include <errno.h>
#include <i2c.h>
#include <linux/media-bus-format.h>
//#include "rtc_iic.h"
#define HYM8563_CTL1 0x00
#define HYM8563_CTL1_TEST BIT(7)
#define HYM8563_CTL1_STOP BIT(5)
#define HYM8563_CTL1_TESTC BIT(3)
#define HYM8563_CTL2 0x01
#define HYM8563_CTL2_TI_TP BIT(4)
#define HYM8563_CTL2_AF BIT(3)
#define HYM8563_CTL2_TF BIT(2)
#define HYM8563_CTL2_AIE BIT(1)
#define HYM8563_CTL2_TIE BIT(0)
struct udevice *rtc_i2c_dev;
#ifdef DEBUG
#define printf_info(fmt, ...) printf(fmt, ##__VA_ARGS__)
#else
#define printf_info(fmt, ...)
#endif
int rtc_write(struct udevice *dev, uint reg, const uint8_t *buff,int len)
{
return dm_i2c_write(dev, reg, buff, len);
}
static int rtc_read(struct udevice *dev, uint reg, uint8_t *buff, int len)
{
return dm_i2c_read(dev, reg, buff, len);
}
int i2c_read_byte_data(u8 command)
{
uint8_t value = 0;
int ret =0;
ret = rtc_read(rtc_i2c_dev,command,&value,1);
if(ret < 0)
{
printf("rtc read error\n");
return ret;
}
else
{
printf("rtc read value=%d\n",value);
return value;
}
}
int i2c_write_byte_data(u8 command, u8 value)
{
int ret =0;
ret = rtc_write(rtc_i2c_dev, command, &value,1);
if(ret < 0)
printf("rtc write error\n");
return ret;
}
#ifdef CONFIG_POWER_ON_STYLE_SUPPORT
extern char IsAllowPower;
#endif
static int hym8563_init_device(void)
{
int ret;
int i;
int reg_value = 0;
/* Clear stop flag if present */
printf_info("##fan## %s\n",__func__);
for(i=0;i<5;i++)
{
ret = i2c_read_byte_data(HYM8563_CTL1);
if(ret>=0)
break;
}
reg_value = i2c_read_byte_data(HYM8563_CTL2);
printf("#### %s,rtc_int_value=0x%x\n",__func__,reg_value);
if (reg_value < 0)
return reg_value;
if(HYM8563_CTL2_AIE & reg_value)
{
if(reg_value & HYM8563_CTL2_AF)
{
IsAllowPower = 1;
printf("#### rtc alarm power on\n");
}
}
ret = i2c_write_byte_data(HYM8563_CTL1, 0);
if (ret < 0)
return ret;
ret = i2c_read_byte_data(HYM8563_CTL2);
if (ret < 0)
return ret;
/* Disable alarm and timer interrupts */
ret &= ~HYM8563_CTL2_AIE;
ret &= ~HYM8563_CTL2_TIE;
/* Clear any pending alarm and timer flags */
if (ret & HYM8563_CTL2_AF)
ret &= ~HYM8563_CTL2_AF;
if (ret & HYM8563_CTL2_TF)
ret &= ~HYM8563_CTL2_TF;
ret &= ~HYM8563_CTL2_TI_TP;
printf_info("#### %s ret=0x%x\n",__func__,ret);
return i2c_write_byte_data(HYM8563_CTL2, ret);
}
static int rtc_probe(struct udevice *dev)
{
rtc_i2c_dev = dev;
printf(" init rtc_probe \n");
hym8563_init_device();
return 0;
}
static const struct udevice_id rtc_of_match[] = {
{ .compatible = "nxp,pcf8563" },
{ .compatible = "haoyu,hym8563" },
{},
};
U_BOOT_DRIVER(hym8563) = {
.name = "hym8563",
.id = UCLASS_I2C_GENERIC,
.of_match = rtc_of_match,
.probe = rtc_probe,
.bind = dm_scan_fdt_dev,
};
Mobile:+86 19926489508/13077808909(Wechat微信同号)
QQ交流群: 712288614