STM32L471re PB5接LED闪烁测试

 PB5设为GPIO_output,其它默认。在main的while里加入

          HAL_GPIO_WritePin(GPIOB, GPIO_PIN_5, GPIO_PIN_RESET);
          HAL_Delay(1000);
          HAL_GPIO_WritePin(GPIOB, GPIO_PIN_5, GPIO_PIN_SET);
          HAL_Delay(1000);

	/* USER CODE BEGIN Header */
	/**
		******************************************************************************
		* @file           : main.c
		* @brief          : Main program body
		******************************************************************************
		* @attention
		*
		* <h2><center>&copy; Copyright (c) 2020 STMicroelectronics.
		* All rights reserved.</center></h2>
		*
		* This software component is licensed by ST under BSD 3-Clause license,
		* the "License"; You may not use this file except in compliance with the
		* License. You may obtain a copy of the License at:
		*                        opensource.org/licenses/BSD-3-Clause
		*
		******************************************************************************
		*/
	/* USER CODE END Header */
	/* Includes ------------------------------------------------------------------*/
	#include "main.h"

	/* Private includes ----------------------------------------------------------*/
	/* USER CODE BEGIN Includes */

	/* USER CODE END Includes */

	/* Private typedef -----------------------------------------------------------*/
	/* USER CODE BEGIN PTD */

	/* USER CODE END PTD */

	/* Private define ------------------------------------------------------------*/
	/* USER CODE BEGIN PD */
	/* USER CODE END PD */

	/* Private macro -------------------------------------------------------------*/
	/* USER CODE BEGIN PM */

	/* USER CODE END PM */

	/* Private variables ---------------------------------------------------------*/

	/* USER CODE BEGIN PV */

	/* USER CODE END PV */

	/* Private function prototypes -----------------------------------------------*/
	void SystemClock_Config(void);
	static void MX_GPIO_Init(void);
	/* USER CODE BEGIN PFP */

	/* USER CODE END PFP */

	/* Private user code ---------------------------------------------------------*/
	/* USER CODE BEGIN 0 */

	/* USER CODE END 0 */

	/**
		* @brief  The application entry point.
		* @retval int
		*/
	int main(void)
	{
		/* USER CODE BEGIN 1 */

		/* USER CODE END 1 */

		/* MCU Configuration--------------------------------------------------------*/

		/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
		HAL_Init();

		/* USER CODE BEGIN Init */

		/* USER CODE END Init */

		/* Configure the system clock */
		SystemClock_Config();

		/* USER CODE BEGIN SysInit */

		/* USER CODE END SysInit */

		/* Initialize all configured peripherals */
		MX_GPIO_Init();
		/* USER CODE BEGIN 2 */

		/* USER CODE END 2 */

		/* Infinite loop */
		/* USER CODE BEGIN WHILE */
		while (1)
		{
				HAL_GPIO_WritePin(GPIOB, GPIO_PIN_5, GPIO_PIN_RESET);
				HAL_Delay(1000);
				HAL_GPIO_WritePin(GPIOB, GPIO_PIN_5, GPIO_PIN_SET);
				HAL_Delay(1000);	
		}
		/* USER CODE END 3 */
	}

	/**
		* @brief System Clock Configuration
		* @retval None
		*/
	void SystemClock_Config(void)
	{
		RCC_OscInitTypeDef RCC_OscInitStruct = {0};
		RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};

		/** Initializes the RCC Oscillators according to the specified parameters
		* in the RCC_OscInitTypeDef structure.
		*/
		RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_MSI;
		RCC_OscInitStruct.MSIState = RCC_MSI_ON;
		RCC_OscInitStruct.MSICalibrationValue = 0;
		RCC_OscInitStruct.MSIClockRange = RCC_MSIRANGE_6;
		RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE;
		if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
		{
			Error_Handler();
		}
		/** Initializes the CPU, AHB and APB buses clocks
		*/
		RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
																|RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
		RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_MSI;
		RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
		RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
		RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;

		if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_0) != HAL_OK)
		{
			Error_Handler();
		}
		/** Configure the main internal regulator output voltage
		*/
		if (HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1) != HAL_OK)
		{
			Error_Handler();
		}
	}

	/**
		* @brief GPIO Initialization Function
		* @param None
		* @retval None
		*/
	static void MX_GPIO_Init(void)
	{
		GPIO_InitTypeDef GPIO_InitStruct = {0};

		/* GPIO Ports Clock Enable */
		__HAL_RCC_GPIOB_CLK_ENABLE();

		/*Configure GPIO pin Output Level */
		HAL_GPIO_WritePin(GPIOB, GPIO_PIN_5, GPIO_PIN_RESET);

		/*Configure GPIO pin : PB5 */
		GPIO_InitStruct.Pin = GPIO_PIN_5;
		GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_PP;
		GPIO_InitStruct.Pull = GPIO_NOPULL;
		GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
		HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);

	}

	/* USER CODE BEGIN 4 */

	/* USER CODE END 4 */

	/**
		* @brief  This function is executed in case of error occurrence.
		* @retval None
		*/
	void Error_Handler(void)
	{
		/* USER CODE BEGIN Error_Handler_Debug */
		/* User can add his own implementation to report the HAL error return state */

		/* USER CODE END Error_Handler_Debug */
	}

	#ifdef  USE_FULL_ASSERT
	/**
		* @brief  Reports the name of the source file and the source line number
		*         where the assert_param error has occurred.
		* @param  file: pointer to the source file name
		* @param  line: assert_param error line source number
		* @retval None
		*/
	void assert_failed(uint8_t *file, uint32_t line)
	{
		/* USER CODE BEGIN 6 */
		/* User can add his own implementation to report the file name and line number,
			 tex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
		/* USER CODE END 6 */
	}
	#endif /* USE_FULL_ASSERT */

	/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/