0.96寸OLED屏使用详解

最新推荐文章于 2024-09-17 22:46:17 发布
最新推荐文章于 2024-09-17 22:46:17 发布
阅读量10w+ 收藏 587
点赞数 112
分类专栏： MCU 文章标签： 函数
本文为博主原创文章，转载请注明出处。
本文链接：https://blog.csdn.net/cow825/article/details/78765024
版权

如何理解OLED分辨率?

这里0.96寸OLED分辨率是128*64;即OLED显示是128行*64列;
但是由于OLED不能一次控制一个点阵,只能控制8个点阵;而且是垂直方向扫描控制;如下图;因此垂直方向坐标可选为0~7;(8*8=64);水平方向可选坐标0~127.
点阵扫描示意图

OLED控制函数

函数参考野火的例程;
OLED_I2C.H

#ifndef __OLED_I2C_H
#define __OLED_I2C_H

#include "stm32f10x.h"

#define OLED_ADDRESS    0x78 //通过调整0R电阻,屏可以0x78和0x7A两个地址 -- 默认0x78

/* STM32 I2C 快速模式 */
#define I2C_Speed              400000

/*I2C接口*/
#define OLED_I2C                          I2C1
#define OLED_I2C_CLK                      RCC_APB1Periph_I2C1
#define OLED_I2C_CLK_INIT                 RCC_APB1PeriphClockCmd

#define OLED_I2C_SCL_PIN                  GPIO_Pin_6                 
#define OLED_I2C_SCL_GPIO_PORT            GPIOB                       
#define OLED_I2C_SCL_GPIO_CLK             RCC_APB2Periph_GPIOB
#define OLED_I2C_SCL_SOURCE               GPIO_PinSource6
#define OLED_I2C_SCL_AF                   GPIO_AF_I2C1

#define OLED_I2C_SDA_PIN                  GPIO_Pin_7                  
#define OLED_I2C_SDA_GPIO_PORT            GPIOB                       
#define OLED_I2C_SDA_GPIO_CLK             RCC_APB2Periph_GPIOB
#define OLED_I2C_SDA_SOURCE               GPIO_PinSource7
#define OLED_I2C_SDA_AF                   GPIO_AF_I2C1

//I2C初始化配置
void I2C_Configuration(void);
void I2C_WriteByte(uint8_t addr,uint8_t data);
void WriteCmd(unsigned char I2C_Command);
void WriteDat(unsigned char I2C_Data);

void OLED_Init(void);
void OLED_SetPos(unsigned char x, unsigned char y);//设置光标位置
void OLED_Fill(unsigned char fill_Data);//填充整个屏幕
void OLED_CLS(void);//清屏
void OLED_ON(void);//将OLED从休眠中唤醒
void OLED_OFF(void);//让OLED休眠 -- 休眠模式下,OLED功耗不到10uA

 /**
  * @brief  OLED_ShowStr，显示codetab.h中的ASCII字符,有6*8和8*16可选择
  * @param  x,y : 起始点坐标(x:0~127, y:0~7);
    *                   ch[] :- 要显示的字符串; 
    *                   TextSize : 字符大小(1:6*8 ; 2:8*16)
    * @retval 无
  */
void OLED_ShowStr(unsigned char x, unsigned char y, unsigned char ch[], unsigned char TextSize);

 /**
  * @brief  OLED_ShowCN，显示codetab.h中的汉字,16*16点阵
  * @param  x,y: 起始点坐标(x:0~127, y:0~7); 
    *                   N:汉字在codetab.h中的索引
    * @retval 无
  */
void OLED_ShowCN(unsigned char x, unsigned char y, unsigned char N);

 /**
  * @brief  OLED_DrawBMP，显示BMP位图
  * @param  x0,y0 :起始点坐标(x0:0~127, y0:0~7);
    *                   x1,y1 : 起点对角线(结束点)的坐标(x1:1~128,y1:1~8)
    * @retval 无
  */
void OLED_DrawBMP(unsigned char x0,unsigned char y0,unsigned char x1,unsigned char y1,unsigned char BMP[]);

#endif

OLED_I2C.C

/**
  ******************************************************************************
  * @file    OLED_I2C.c
  * @author  fire
  * @version V1.0
  * @date    2014-xx-xx
  * @brief   128*64点阵的OLED显示屏驱动文件，仅适用于SD1306驱动IIC通信方式显示屏
  ******************************************************************************
  * @attention
  *
  * 实验平台:秉火 F103-指南者 STM32 开发板 
  * 论坛    :http://www.firebbs.cn
  * 淘宝    :https://fire-stm32.taobao.com

    * Function List:
    *   1. void I2C_Configuration(void) -- 配置CPU的硬件I2C
    * 2. void I2C_WriteByte(uint8_t addr,uint8_t data) -- 向寄存器地址写一个byte的数据
    * 3. void WriteCmd(unsigned char I2C_Command) -- 写命令
    * 4. void WriteDat(unsigned char I2C_Data) -- 写数据
    * 5. void OLED_Init(void) -- OLED屏初始化
    * 6. void OLED_SetPos(unsigned char x, unsigned char y) -- 设置起始点坐标
    * 7. void OLED_Fill(unsigned char fill_Data) -- 全屏填充
    * 8. void OLED_CLS(void) -- 清屏
    * 9. void OLED_ON(void) -- 唤醒
    * 10. void OLED_OFF(void) -- 睡眠
    * 11. void OLED_ShowStr(unsigned char x, unsigned char y, unsigned char ch[], unsigned char TextSize) -- 显示字符串(字体大小有6*8和8*16两种)
    * 12. void OLED_ShowCN(unsigned char x, unsigned char y, unsigned char N) -- 显示中文(中文需要先取模，然后放到codetab.h中)
    * 13. void OLED_DrawBMP(unsigned char x0,unsigned char y0,unsigned char x1,unsigned char y1,unsigned char BMP[]) -- BMP图片
    *
  *
  ******************************************************************************
  */ 




#include "OLED_I2C.h"
#include "codetab.h"//点阵数据
#include "bsp_SysTick.h"



 /**
  * @brief  I2C_Configuration，初始化硬件IIC引脚
  * @param  无
  * @retval 无
  */
void I2C_Configuration(void)
{
    I2C_InitTypeDef  I2C_InitStructure;
    GPIO_InitTypeDef  GPIO_InitStructure; 

    /*I2C1外设时钟使能 */
    OLED_I2C_CLK_INIT(OLED_I2C_CLK,ENABLE);

    /*I2C1外设GPIO时钟使能 */
    RCC_APB2PeriphClockCmd(OLED_I2C_SCL_GPIO_CLK | OLED_I2C_SDA_GPIO_CLK,ENABLE);

     /* I2C_SCL、I2C_SDA*/
  GPIO_InitStructure.GPIO_Pin = OLED_I2C_SCL_PIN;
  GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
  GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_OD;          // 开漏输出
  GPIO_Init(OLED_I2C_SCL_GPIO_PORT, &GPIO_InitStructure);

  GPIO_InitStructure.GPIO_Pin = OLED_I2C_SDA_PIN;
  GPIO_Init(OLED_I2C_SDA_GPIO_PORT, &GPIO_InitStructure);   


    /* I2C 配置 */
  I2C_InitStructure.I2C_Mode = I2C_Mode_I2C;    
  I2C_InitStructure.I2C_DutyCycle = I2C_DutyCycle_2;    /* 高电平数据稳定，低电平数据变化 SCL 时钟线的占空比 */
  I2C_InitStructure.I2C_OwnAddress1 =0x10;    //主机的I2C地址.和其它设备不重复即可
  I2C_InitStructure.I2C_Ack = I2C_Ack_Enable ;  
  I2C_InitStructure.I2C_AcknowledgedAddress = I2C_AcknowledgedAddress_7bit; /* I2C的寻址模式 */
  I2C_InitStructure.I2C_ClockSpeed = I2C_Speed;                             /* 通信速率 */

  I2C_Init(OLED_I2C, &I2C_InitStructure);                                         /* I2C1 初始化 */
  I2C_Cmd(OLED_I2C, ENABLE);                                                    /* 使能 I2C1 */

}


 /**
  * @brief  I2C_WriteByte，向OLED寄存器地址写一个byte的数据
  * @param  addr：寄存器地址
    *                   data：要写入的数据
  * @retval 无
  */
void I2C_WriteByte(uint8_t addr,uint8_t data)
{
  while(I2C_GetFlagStatus(I2C1, I2C_FLAG_BUSY));

    I2C_GenerateSTART(I2C1, ENABLE);//开启I2C1
    while(!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_MODE_SELECT));/*EV5,主模式*/

    I2C_Send7bitAddress(I2C1, OLED_ADDRESS, I2C_Direction_Transmitter);//器件地址 -- 默认0x78
    while(!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_TRANSMITTER_MODE_SELECTED));

    I2C_SendData(I2C1, addr);//寄存器地址
    while (!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_BYTE_TRANSMITTED));

    I2C_SendData(I2C1, data);//发送数据
    while (!I2C_CheckEvent(I2C1, I2C_EVENT_MASTER_BYTE_TRANSMITTED));

    I2C_GenerateSTOP(I2C1, ENABLE);//关闭I2C1总线
}


 /**
  * @brief  WriteCmd，向OLED写入命令
  * @param  I2C_Command：命令代码
  * @retval 无
  */
void WriteCmd(unsigned char I2C_Command)//写命令
{
    I2C_WriteByte(0x00, I2C_Command);
}


 /**
  * @brief  WriteDat，向OLED写入数据
  * @param  I2C_Data：数据
  * @retval 无
  */
void WriteDat(unsigned char I2C_Data)//写数据
{
    I2C_WriteByte(0x40, I2C_Data);
}


 /**
  * @brief  OLED_Init，初始化OLED
  * @param  无
  * @retval 无
  */
void OLED_Init(void)
{
    Delay_ms(1000);     // 1s,这里的延时很重要,上电后延时，没有错误的冗余设计

    WriteCmd(0xAE); //display off
    WriteCmd(0x20); //Set Memory Addressing Mode    
    WriteCmd(0x10); //00,Horizontal Addressing Mode;01,Vertical Addressing Mode;10,Page Addressing Mode (RESET);11,Invalid
    WriteCmd(0xb0); //Set Page Start Address for Page Addressing Mode,0-7
    WriteCmd(0xc8); //Set COM Output Scan Direction
    WriteCmd(0x00); //---set low column address
    WriteCmd(0x10); //---set high column address
    WriteCmd(0x40); //--set start line address
    WriteCmd(0x81); //--set contrast control register
    WriteCmd(0xff); //亮度调节 0x00~0xff
    WriteCmd(0xa1); //--set segment re-map 0 to 127
    WriteCmd(0xa6); //--set normal display
    WriteCmd(0xa8); //--set multiplex ratio(1 to 64)
    WriteCmd(0x3F); //
    WriteCmd(0xa4); //0xa4,Output follows RAM content;0xa5,Output ignores RAM content
    WriteCmd(0xd3); //-set display offset
    WriteCmd(0x00); //-not offset
    WriteCmd(0xd5); //--set display clock divide ratio/oscillator frequency
    WriteCmd(0xf0); //--set divide ratio
    WriteCmd(0xd9); //--set pre-charge period
    WriteCmd(0x22); //
    WriteCmd(0xda); //--set com pins hardware configuration
    WriteCmd(0x12);
    WriteCmd(0xdb); //--set vcomh
    WriteCmd(0x20); //0x20,0.77xVcc
    WriteCmd(0x8d); //--set DC-DC enable
    WriteCmd(0x14); //
    WriteCmd(0xaf); //--turn on oled panel
}


 /**
  * @brief  OLED_SetPos，设置光标
  * @param  x,光标x位置
    *                   y，光标y位置
  * @retval 无
  */
void OLED_SetPos(unsigned char x, unsigned char y) //设置起始点坐标
{ 
    WriteCmd(0xb0+y);
    WriteCmd(((x&0xf0)>>4)|0x10);
    WriteCmd((x&0x0f)|0x01);
}

 /**
  * @brief  OLED_Fill，填充整个屏幕
  * @param  fill_Data:要填充的数据
    * @retval 无
  */
void OLED_Fill(unsigned char fill_Data)//全屏填充
{
    unsigned char m,n;
    for(m=0;m<8;m++)
    {
        WriteCmd(0xb0+m);       //page0-page1
        WriteCmd(0x00);     //low column start address
        WriteCmd(0x10);     //high column start address
        for(n=0;n<128;n++)
            {
                WriteDat(fill_Data);
            }
    }
}

 /**
  * @brief  OLED_CLS，清屏
  * @param  无
    * @retval 无
  */
void OLED_CLS(void)//清屏
{
    OLED_Fill(0x00);
}


 /**
  * @brief  OLED_ON，将OLED从休眠中唤醒
  * @param  无
    * @retval 无
  */
void OLED_ON(void)
{
    WriteCmd(0X8D);  //设置电荷泵
    WriteCmd(0X14);  //开启电荷泵
    WriteCmd(0XAF);  //OLED唤醒
}


 /**
  * @brief  OLED_OFF，让OLED休眠 -- 休眠模式下,OLED功耗不到10uA
  * @param  无
    * @retval 无
  */
void OLED_OFF(void)
{
    WriteCmd(0X8D);  //设置电荷泵
    WriteCmd(0X10);  //关闭电荷泵
    WriteCmd(0XAE);  //OLED休眠
}


 /**
  * @brief  OLED_ShowStr，显示codetab.h中的ASCII字符,有6*8和8*16可选择
  * @param  x,y : 起始点坐标(x:0~127, y:0~7);
    *                   ch[] :- 要显示的字符串; 
    *                   TextSize : 字符大小(1:6*8 ; 2:8*16)
    * @retval 无
  */
void OLED_ShowStr(unsigned char x, unsigned char y, unsigned char ch[], unsigned char TextSize)
{
    unsigned char c = 0,i = 0,j = 0;
    switch(TextSize)
    {
        case 1:
        {
            while(ch[j] != '\0')
            {
                c = ch[j] - 32;
                if(x > 126)
                {
                    x = 0;
                    y++;
                }
                OLED_SetPos(x,y);
                for(i=0;i<6;i++)
                    WriteDat(F6x8[c][i]);
                x += 6;
                j++;
            }
        }break;
        case 2:
        {
            while(ch[j] != '\0')
            {
                c = ch[j] - 32;
                if(x > 120)
                {
                    x = 0;
                    y++;
                }
                OLED_SetPos(x,y);
                for(i=0;i<8;i++)
                    WriteDat(F8X16[c*16+i]);
                OLED_SetPos(x,y+1);
                for(i=0;i<8;i++)
                    WriteDat(F8X16[c*16+i+8]);
                x += 8;
                j++;
            }
        }break;
    }
}

 /**
  * @brief  OLED_ShowCN，显示codetab.h中的汉字,16*16点阵
  * @param  x,y: 起始点坐标(x:0~127, y:0~7); 
    *                   N:汉字在codetab.h中的索引
    * @retval 无
  */
void OLED_ShowCN(unsigned char x, unsigned char y, unsigned char N)
{
    unsigned char wm=0;
    unsigned int  adder=32*N;
    OLED_SetPos(x , y);
    for(wm = 0;wm < 16;wm++)
    {
        WriteDat(F16x16[adder]);
        adder += 1;
    }
    OLED_SetPos(x,y + 1);
    for(wm = 0;wm < 16;wm++)
    {
        WriteDat(F16x16[adder]);
        adder += 1;
    }
}



 /**
  * @brief  OLED_DrawBMP，显示BMP位图
  * @param  x0,y0 :起始点坐标(x0:0~127, y0:0~7);
    *                   x1,y1 : 起点对角线(结束点)的坐标(x1:1~128,y1:1~8)
    * @retval 无
  */
void OLED_DrawBMP(unsigned char x0,unsigned char y0,unsigned char x1,unsigned char y1,unsigned char BMP[])
{
    unsigned int j=0;
    unsigned char x,y;

  if(y1%8==0)
        y = y1/8;
  else
        y = y1/8 + 1;
    for(y=y0;y<y1;y++)
    {
        OLED_SetPos(x0,y);
    for(x=x0;x<x1;x++)
        {
            WriteDat(BMP[j++]);
        }
    }
}

CODETAB.H

/**
  ******************************************************************************
  * @file    codetab.h
  * @author  fire
  * @version V1.0
  * @date    2014-xx-xx
  * @brief   128*64点阵的OLED显示测试工程，仅适用于SD1306驱动IIC通信方式显示屏
  ******************************************************************************
  * @attention  *
    * 
    * 1. 128*64点整OLED模块功能演示程序的字表，仅适用heltec.taobao.com所售产品;
    * 2. 字表由打包资料中的“取字软件”计算得出;
    * 3. 取字方式 -- 共阴、列行式、逆向输出
    *
  *
  ******************************************************************************
  */ 
#ifndef __CODETAB_H
#define __CODETAB_H


/***************************16*16的点阵字体取模方式：共阴——列行式——逆向输出*********/
unsigned char F16x16[] =
{   0x00,0xF0,0x90,0x88,0x88,0x88,0x88,0xFE,0x88,0x88,0x88,0x88,0x90,0xF0,0x00,0x00,
    0x00,0x0F,0x08,0x08,0x08,0x08,0x08,0xFF,0x88,0x88,0x88,0x88,0x88,0x8F,0x60,0x00,//电0

    0x00,0x00,0x04,0x04,0x04,0x04,0x04,0x44,0xA4,0x14,0x14,0x0C,0x04,0x00,0x00,0x00,
    0x00,0x01,0x01,0x41,0x41,0x81,0x81,0x81,0x81,0x47,0x39,0x01,0x01,0x01,0x01,0x00,//子1

    0x00,0x20,0x10,0xF8,0x2C,0x26,0x24,0x24,0xA4,0x34,0x2C,0x20,0x20,0xC0,0x00,0x00,
    0x00,0x80,0x80,0xBF,0x40,0x40,0x20,0x1C,0x03,0x00,0x20,0x40,0x40,0xBF,0x80,0x00,//负2

    0x00,0xA0,0xA0,0xA8,0xE8,0xBE,0xA8,0xA8,0xA8,0xA0,0x3C,0xE0,0x24,0xE8,0x28,0x00,
    0x00,0x00,0x24,0x27,0x24,0x25,0xFE,0x24,0x24,0x90,0x40,0x37,0x3C,0x43,0xF8,0x00,//载3

};


/************************************6*8的点阵************************************/
const unsigned char F6x8[][6] =
{
    0x00, 0x00, 0x00, 0x00, 0x00, 0x00,// sp
    0x00, 0x00, 0x00, 0x2f, 0x00, 0x00,// !
    0x00, 0x00, 0x07, 0x00, 0x07, 0x00,// "
    0x00, 0x14, 0x7f, 0x14, 0x7f, 0x14,// #
    0x00, 0x24, 0x2a, 0x7f, 0x2a, 0x12,// $
    0x00, 0x62, 0x64, 0x08, 0x13, 0x23,// %
    0x00, 0x36, 0x49, 0x55, 0x22, 0x50,// &
    0x00, 0x00, 0x05, 0x03, 0x00, 0x00,// '
    0x00, 0x00, 0x1c, 0x22, 0x41, 0x00,// (
    0x00, 0x00, 0x41, 0x22, 0x1c, 0x00,// )
    0x00, 0x14, 0x08, 0x3E, 0x08, 0x14,// *
    0x00, 0x08, 0x08, 0x3E, 0x08, 0x08,// +
    0x00, 0x00, 0x00, 0xA0, 0x60, 0x00,// ,
    0x00, 0x08, 0x08, 0x08, 0x08, 0x08,// -
    0x00, 0x00, 0x60, 0x60, 0x00, 0x00,// .
    0x00, 0x20, 0x10, 0x08, 0x04, 0x02,// /
    0x00, 0x3E, 0x51, 0x49, 0x45, 0x3E,// 0
    0x00, 0x00, 0x42, 0x7F, 0x40, 0x00,// 1
    0x00, 0x42, 0x61, 0x51, 0x49, 0x46,// 2
    0x00, 0x21, 0x41, 0x45, 0x4B, 0x31,// 3
    0x00, 0x18, 0x14, 0x12, 0x7F, 0x10,// 4
    0x00, 0x27, 0x45, 0x45, 0x45, 0x39,// 5
    0x00, 0x3C, 0x4A, 0x49, 0x49, 0x30,// 6
    0x00, 0x01, 0x71, 0x09, 0x05, 0x03,// 7
    0x00, 0x36, 0x49, 0x49, 0x49, 0x36,// 8
    0x00, 0x06, 0x49, 0x49, 0x29, 0x1E,// 9
    0x00, 0x00, 0x36, 0x36, 0x00, 0x00,// :
    0x00, 0x00, 0x56, 0x36, 0x00, 0x00,// ;
    0x00, 0x08, 0x14, 0x22, 0x41, 0x00,// <
    0x00, 0x14, 0x14, 0x14, 0x14, 0x14,// =
    0x00, 0x00, 0x41, 0x22, 0x14, 0x08,// >
    0x00, 0x02, 0x01, 0x51, 0x09, 0x06,// ?
    0x00, 0x32, 0x49, 0x59, 0x51, 0x3E,// @
    0x00, 0x7C, 0x12, 0x11, 0x12, 0x7C,// A
    0x00, 0x7F, 0x49, 0x49, 0x49, 0x36,// B
    0x00, 0x3E, 0x41, 0x41, 0x41, 0x22,// C
    0x00, 0x7F, 0x41, 0x41, 0x22, 0x1C,// D
    0x00, 0x7F, 0x49, 0x49, 0x49, 0x41,// E
    0x00, 0x7F, 0x09, 0x09, 0x09, 0x01,// F
    0x00, 0x3E, 0x41, 0x49, 0x49, 0x7A,// G
    0x00, 0x7F, 0x08, 0x08, 0x08, 0x7F,// H
    0x00, 0x00, 0x41, 0x7F, 0x41, 0x00,// I
    0x00, 0x20, 0x40, 0x41, 0x3F, 0x01,// J
    0x00, 0x7F, 0x08, 0x14, 0x22, 0x41,// K
    0x00, 0x7F, 0x40, 0x40, 0x40, 0x40,// L
    0x00, 0x7F, 0x02, 0x0C, 0x02, 0x7F,// M
    0x00, 0x7F, 0x04, 0x08, 0x10, 0x7F,// N
    0x00, 0x3E, 0x41, 0x41, 0x41, 0x3E,// O
    0x00, 0x7F, 0x09, 0x09, 0x09, 0x06,// P
    0x00, 0x3E, 0x41, 0x51, 0x21, 0x5E,// Q
    0x00, 0x7F, 0x09, 0x19, 0x29, 0x46,// R
    0x00, 0x46, 0x49, 0x49, 0x49, 0x31,// S
    0x00, 0x01, 0x01, 0x7F, 0x01, 0x01,// T
    0x00, 0x3F, 0x40, 0x40, 0x40, 0x3F,// U
    0x00, 0x1F, 0x20, 0x40, 0x20, 0x1F,// V
    0x00, 0x3F, 0x40, 0x38, 0x40, 0x3F,// W
    0x00, 0x63, 0x14, 0x08, 0x14, 0x63,// X
    0x00, 0x07, 0x08, 0x70, 0x08, 0x07,// Y
    0x00, 0x61, 0x51, 0x49, 0x45, 0x43,// Z
    0x00, 0x00, 0x7F, 0x41, 0x41, 0x00,// [
    0x00, 0x55, 0x2A, 0x55, 0x2A, 0x55,// 55
    0x00, 0x00, 0x41, 0x41, 0x7F, 0x00,// ]
    0x00, 0x04, 0x02, 0x01, 0x02, 0x04,// ^
    0x00, 0x40, 0x40, 0x40, 0x40, 0x40,// _
    0x00, 0x00, 0x01, 0x02, 0x04, 0x00,// '
    0x00, 0x20, 0x54, 0x54, 0x54, 0x78,// a
    0x00, 0x7F, 0x48, 0x44, 0x44, 0x38,// b
    0x00, 0x38, 0x44, 0x44, 0x44, 0x20,// c
    0x00, 0x38, 0x44, 0x44, 0x48, 0x7F,// d
    0x00, 0x38, 0x54, 0x54, 0x54, 0x18,// e
    0x00, 0x08, 0x7E, 0x09, 0x01, 0x02,// f
    0x00, 0x18, 0xA4, 0xA4, 0xA4, 0x7C,// g
    0x00, 0x7F, 0x08, 0x04, 0x04, 0x78,// h
    0x00, 0x00, 0x44, 0x7D, 0x40, 0x00,// i
    0x00, 0x40, 0x80, 0x84, 0x7D, 0x00,// j
    0x00, 0x7F, 0x10, 0x28, 0x44, 0x00,// k
    0x00, 0x00, 0x41, 0x7F, 0x40, 0x00,// l
    0x00, 0x7C, 0x04, 0x18, 0x04, 0x78,// m
    0x00, 0x7C, 0x08, 0x04, 0x04, 0x78,// n
    0x00, 0x38, 0x44, 0x44, 0x44, 0x38,// o
    0x00, 0xFC, 0x24, 0x24, 0x24, 0x18,// p
    0x00, 0x18, 0x24, 0x24, 0x18, 0xFC,// q
    0x00, 0x7C, 0x08, 0x04, 0x04, 0x08,// r
    0x00, 0x48, 0x54, 0x54, 0x54, 0x20,// s
    0x00, 0x04, 0x3F, 0x44, 0x40, 0x20,// t
    0x00, 0x3C, 0x40, 0x40, 0x20, 0x7C,// u
    0x00, 0x1C, 0x20, 0x40, 0x20, 0x1C,// v
    0x00, 0x3C, 0x40, 0x30, 0x40, 0x3C,// w
    0x00, 0x44, 0x28, 0x10, 0x28, 0x44,// x
    0x00, 0x1C, 0xA0, 0xA0, 0xA0, 0x7C,// y
    0x00, 0x44, 0x64, 0x54, 0x4C, 0x44,// z
    0x14, 0x14, 0x14, 0x14, 0x14, 0x14,// horiz lines
};
/****************************************8*16的点阵************************************/
const unsigned char F8X16[]=      
{
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,// 0
  0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x33,0x30,0x00,0x00,0x00,//! 1
  0x00,0x10,0x0C,0x06,0x10,0x0C,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//" 2
  0x40,0xC0,0x78,0x40,0xC0,0x78,0x40,0x00,0x04,0x3F,0x04,0x04,0x3F,0x04,0x04,0x00,//# 3
  0x00,0x70,0x88,0xFC,0x08,0x30,0x00,0x00,0x00,0x18,0x20,0xFF,0x21,0x1E,0x00,0x00,//$ 4
  0xF0,0x08,0xF0,0x00,0xE0,0x18,0x00,0x00,0x00,0x21,0x1C,0x03,0x1E,0x21,0x1E,0x00,//% 5
  0x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00,0x1E,0x21,0x23,0x24,0x19,0x27,0x21,0x10,//& 6
  0x10,0x16,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//' 7
  0x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00,0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00,//( 8
  0x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00,0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00,//) 9
  0x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00,0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00,//* 10
  0x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x1F,0x01,0x01,0x01,0x00,//+ 11
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0xB0,0x70,0x00,0x00,0x00,0x00,0x00,//, 12
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,//- 13
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,//. 14
  0x00,0x00,0x00,0x00,0x80,0x60,0x18,0x04,0x00,0x60,0x18,0x06,0x01,0x00,0x00,0x00,/// 15
  0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00,//0 16
  0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//1 17
  0x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00,//2 18
  0x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00,//3 19
  0x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00,//4 20
  0x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00,//5 21
  0x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00,//6 22
  0x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,//7 23
  0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00,//8 24
  0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00,//9 25
  0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,//: 26
  0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x60,0x00,0x00,0x00,0x00,//; 27
  0x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00,0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00,//< 28
  0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x00,//= 29
  0x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00,0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00,//> 30
  0x00,0x70,0x48,0x08,0x08,0x08,0xF0,0x00,0x00,0x00,0x00,0x30,0x36,0x01,0x00,0x00,//? 31
  0xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00,0x07,0x18,0x27,0x24,0x23,0x14,0x0B,0x00,//@ 32
  0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20,//A 33
  0x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00,//B 34
  0xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00,//C 35
  0x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00,//D 36
  0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00,//E 37
  0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00,//F 38
  0xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00,0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00,//G 39
  0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20,//H 40
  0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//I 41
  0x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00,//J 42
  0x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00,0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00,//K 43
  0x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00,0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00,//L 44
  0x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00,0x20,0x3F,0x00,0x3F,0x00,0x3F,0x20,0x00,//M 45
  0x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08,0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00,//N 46
  0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00,//O 47
  0x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00,0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00,//P 48
  0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,0x0F,0x18,0x24,0x24,0x38,0x50,0x4F,0x00,//Q 49
  0x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20,//R 50
  0x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00,0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00,//S 51
  0x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//T 52
  0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//U 53
  0x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00,//V 54
  0xF8,0x08,0x00,0xF8,0x00,0x08,0xF8,0x00,0x03,0x3C,0x07,0x00,0x07,0x3C,0x03,0x00,//W 55
  0x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08,0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20,//X 56
  0x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00,0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//Y 57
  0x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00,0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00,//Z 58
  0x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00,0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00,//[ 59
  0x00,0x0C,0x30,0xC0,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00,//\ 60
  0x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00,//] 61
  0x00,0x00,0x04,0x02,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//^ 62
  0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,//_ 63
  0x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//` 64
  0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20,//a 65
  0x08,0xF8,0x00,0x80,0x80,0x00,0x00,0x00,0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00,//b 66
  0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00,//c 67
  0x00,0x00,0x00,0x80,0x80,0x88,0xF8,0x00,0x00,0x0E,0x11,0x20,0x20,0x10,0x3F,0x20,//d 68
  0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00,//e 69
  0x00,0x80,0x80,0xF0,0x88,0x88,0x88,0x18,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//f 70
  0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00,//g 71
  0x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//h 72
  0x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//i 73
  0x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00,0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,//j 74
  0x08,0xF8,0x00,0x00,0x80,0x80,0x80,0x00,0x20,0x3F,0x24,0x02,0x2D,0x30,0x20,0x00,//k 75
  0x00,0x08,0x08,0xF8,0x00,0x00,0x00,0x00,0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//l 76
  0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F,//m 77
  0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//n 78
  0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//o 79
  0x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00,0x80,0xFF,0xA1,0x20,0x20,0x11,0x0E,0x00,//p 80
  0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,0x0E,0x11,0x20,0x20,0xA0,0xFF,0x80,//q 81
  0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00,//r 82
  0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00,//s 83
  0x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00,//t 84
  0x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00,0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20,//u 85
  0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x00,0x01,0x0E,0x30,0x08,0x06,0x01,0x00,//v 86
  0x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80,0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00,//w 87
  0x00,0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,0x20,0x31,0x2E,0x0E,0x31,0x20,0x00,//x 88
  0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,0x80,0x81,0x8E,0x70,0x18,0x06,0x01,0x00,//y 89
  0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00,//z 90
  0x00,0x00,0x00,0x00,0x80,0x7C,0x02,0x02,0x00,0x00,0x00,0x00,0x00,0x3F,0x40,0x40,//{ 91
  0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,//| 92
  0x00,0x02,0x02,0x7C,0x80,0x00,0x00,0x00,0x00,0x40,0x40,0x3F,0x00,0x00,0x00,0x00,//} 93
  0x00,0x06,0x01,0x01,0x02,0x02,0x04,0x04,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//~ 94
};

unsigned char BMP1[] =
{
    0x00,0x03,0x05,0x09,0x11,0xFF,0x11,0x89,0x05,0xC3,0x00,0xE0,0x00,0xF0,0x00,0xF8,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x44,0x28,0xFF,0x11,0xAA,0x44,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x83,0x01,0x38,0x44,0x82,0x92,
    0x92,0x74,0x01,0x83,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x7C,0x44,0xC7,0x01,0x7D,
    0x7D,0x7D,0x7D,0x01,0x7D,0x7D,0x7D,0x7D,0x01,0x7D,0x7D,0x7D,0x7D,0x01,0xFF,0x00,
    0x00,0x00,0x00,0x00,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,0x00,0x01,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x00,0x00,0x00,0x00,
    0x00,0x00,0x01,0x01,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x01,0x01,0x01,
    0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x01,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x40,0x40,0x40,0x40,0x40,0x00,0x00,
    0x6D,0x6D,0x6D,0x6D,0x6D,0x00,0x00,0x60,0x60,0x60,0x60,0x60,0x00,0x00,0x40,0x40,
    0x40,0x40,0x40,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xDB,0xDB,0xDB,0xDB,0xDB,0x00,0x00,
    0xDB,0xDB,0xDB,0xDB,0xDB,0x00,0x00,0xDB,0xDB,0xDB,0xDB,0xDB,0x00,0x00,0xDB,0xDB,
    0xDB,0xDB,0xDB,0x00,0x00,0xDA,0xDA,0xDA,0xDA,0xDA,0x00,0x00,0xD8,0xD8,0xD8,0xD8,
    0xD8,0x00,0x00,0xC0,0xC0,0xC0,0xC0,0xC0,0x00,0x00,0xC0,0xC0,0xC0,0xC0,0xC0,0x00,
    0x00,0xC0,0xC0,0xC0,0xC0,0xC0,0x00,0x00,0xC0,0xC0,0xC0,0xC0,0xC0,0x00,0x00,0x80,
    0x80,0x80,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x06,0x06,0x06,0x06,0x06,0x00,0x00,
    0x06,0x06,0x06,0x06,0x06,0x00,0x00,0x06,0x06,0x06,0x06,0x06,0x00,0x00,0x06,0x06,
    0x06,0x06,0x06,0x00,0x00,0x06,0x06,0x06,0xE6,0x66,0x20,0x00,0x06,0x06,0x86,0x06,
    0x06,0x00,0x00,0x06,0x06,0x06,0x06,0x86,0x00,0x00,0x06,0x06,0x06,0x06,0x06,0x00,
    0x00,0x86,0x86,0x86,0x86,0x86,0x80,0x80,0x86,0x86,0x06,0x86,0x86,0xC0,0xC0,0x86,
    0x86,0x86,0x06,0x06,0xD0,0x30,0x76,0x06,0x06,0x06,0x06,0x00,0x00,0x06,0x06,0x06,
    0x06,0x06,0x00,0x00,0x06,0x06,0x06,0x06,0x06,0x00,0x00,0x06,0x06,0x06,0x06,0x06,
    0x00,0x00,0x06,0x06,0x06,0x06,0x06,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x60,0x1C,0x00,0xFE,0x00,0x01,
    0x02,0x00,0xC4,0x18,0x20,0x02,0x9E,0x63,0xB2,0x0E,0x00,0xFF,0x81,0x81,0xFF,0x00,
    0x00,0x80,0x40,0x30,0x0F,0x00,0x00,0x00,0x00,0xFF,0x00,0x23,0xEA,0xAA,0xBF,0xAA,
    0xEA,0x03,0x3F,0x00,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x0E,0x0C,0x08,0x00,0x00,0x01,0x01,0x01,
    0x01,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,0x01,0x00,0x81,0x80,0x80,0x81,0x80,
    0x81,0x80,0x80,0x80,0x80,0x01,0x01,0x01,0x01,0x00,0x00,0x00,0x01,0x00,0x00,0x00,
    0x01,0x00,0x01,0x01,0x09,0x0C,0x0E,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,
    0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0xC0,0x00,
    0x00,0x1E,0x21,0x40,0x40,0x50,0x21,0x5E,0x00,0x1E,0x21,0x40,0x40,0x50,0x21,0x5E,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0xC1,0xC1,0xFF,
    0xFF,0xC1,0xC1,0xFF,0xFF,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0xFF,0xFF,0x80,0xFC,0xF3,0xEF,0xF3,0xFC,
    0x80,0xFF,0x80,0xEE,0xEE,0xEE,0xF5,0xFB,0xFF,0x9C,0xBE,0xB6,0xB6,0x88,0xFF,0x00,/*"D:\DreamSpark\OLED\MP3_UI.bmp",0*/
};


#endif

函数功能&理解

设置位置函数

/**
* @brief OLED_SetPos，设置光标
* @param x,光标x位置,即行位置,取值0~127
* y，光标y位置,即列位置,取值0~7;
* @retval 无
*/
void OLED_SetPos(unsigned char x, unsigned char y) //设置起始点坐标

写字符串函数

/**
* @brief OLED_ShowStr，显示codetab.h中的ASCII字符,有6*8和8*16可选择
* @param x,y : 起始点坐标(x:0~127, y:0~7);
* ch[] :- 要显示的字符串;
* TextSize : 字符大小(1:6*8 ; 2:8*16)
* @retval 无
*/
void OLED_ShowStr(unsigned char x, unsigned char y, unsigned char ch[], unsigned char TextSize)

例子: OLED_ShowStr(90,1,”–YUAN”,1);
在第一行,第90列显示引号内的字符串;

写汉字程序

首先用取模软件把汉字编码写好,存放到相应的数组中;
/**
* @brief OLED_ShowCN，显示codetab.h中的汉字,16*16点阵
* @param x,y: 起始点坐标(x:0~127, y:0~7);
* N:汉字在codetab.h中的索引
* @retval 无
*/
void OLED_ShowCN(unsigned char x, unsigned char y, unsigned char N)

例程: //显示汉字”电子负载”
for(i=0;i<4;i++)
{
OLED_ShowCN(10+i*16,0,i); //测试
}

写BMP图片

首先把BMP图片调整为黑白图像,像素128*64;图片导入到取字软件,自动生成代码;下面会讲~~

/**
* @brief OLED_DrawBMP，显示BMP位图
* @param x0,y0 :起始点坐标(x0:0~127, y0:0~7);
* x1,y1 : 起点对角线(结束点)的坐标(x1:1~128,y1:1~8)
* @retval 无
*/
void OLED_DrawBMP(unsigned char x0,unsigned char y0,unsigned char x1,unsigned char y1,unsigned char BMP[])

例程:OLED_DrawBMP(0,0,128,8,(unsigned char *)BMP2);

其它函数

填充屏幕&清屏

休眠&唤醒

取字软件的使用

  • 配置取字软件
  • 输入汉字或导入BMP图片,生成字模
  • 把字模导入相应的数组,调用即可显示

取字软件配置

BretLi
关注
专栏目录
0.96寸OLED显示屏用户资料
06-25
0.96寸OLED显示屏用户资料，包含程序和技术资料。
0.96寸OLED显示屏显示字符串、汉字（stm32标准库）
qq_50749196的博客
08-09 5341
OLED，即有机发光二极管OLED由于同时具备自发光，不需背光源、对比度高、厚度薄、视角广、反应速度快、可用于挠曲性面板、使用温度范围广、构造及制程较简单等优异之特性，被认为是下一代的平面显示器新兴应用技术。OLED显示其实说白了就是对于像素点的点亮和熄灭进行操作。本文采用的是4针的0.96寸OLED显示进行讲解，采用的是模拟IIC协议，屏幕整体分辨率为128*64驱动芯片为SSD1306，下面是引脚功能介绍。0.96寸OLED屏幕显示引脚介绍名称注释GND电源地VCC电源正（3.3～5V）
STM32外设-0.96寸OLED显示屏
最新发布
xuhc_zd的博客
09-17 1787
STM32外设-0.96寸OLED显示屏
0.96寸OLED液晶显示器
u011816009的博客
04-22 1万+
OLED被称为有机激光二极管，也被称为有机激光显示，OLED采用有机材料涂层和玻璃基板，当有电流通过时有机材料就会发光，所以OLED具有自发光特性，不需要背光源（只上电不会亮的，需要完整的程序驱动）下图所示是我们项目中常用的0.96寸的OLED液晶显示屏（图片来源于网络），其有4pin（IIC接口）和7pin（SPI接口）两种，它的显示区域是128X64的点阵，每个点都可以自己独立发光，所以不需要背光，可以显示汉字、ASIIC码、图案等，分别对其进行介绍。
0.96寸OLED（SSD1306）屏幕显示（一）——基础功能介绍
热门推荐
qq_35953617的博客
12-27 8万+
最近，我突发奇想去翻阅了一些我本科期间所做的一些小项目，发现都挺有意思的！当年做这些项目的时候可走了很多弯路，所以想着可以将它们上传到网络上，并通过我的讲解文章可以帮助你们少走一些弯路！今天，我要分享的是一个0.96寸OLED（SSD1306）屏幕显示的学习笔记，因为我想要讲的详细一点，所以打算做成一个系列，手把手地教你学习和认识屏幕显示。由于我知识有限，如果出现一些错误，希望大家可以帮助我指出来，我们一起学习进步！！！OLED，即有机发光二极管OLED由于同时具备。
0.96寸OLED显示屏介绍
weichen_78的博客
12-22 1万+
OLED，即有机发光二极管（Organic Light Emitting Diode）。OLED 由于同时具备自发光，不需背光源、对比度高、厚度薄、视角广、反应速度快、可用于挠曲性面板、使用温度范围广、构造及制程较简单等优异之特性，被认为是下一代的平面显示器新兴应用技术。
【mcuclub】0.96寸oled显示屏
weixin_61121477的博客
11-08 1万+
OLED显示屏
0.96寸OLED屏原理图
07-12
### 0.96寸OLED屏原理图详解 #### OLED技术概述 OLED（Organic Light Emitting Diodes）即有机发光二极管，是一种显示技术，它使用有机材料来制造显示屏幕上的像素。与传统的LCD技术不同，OLED不需要背光灯，每个...
0.96寸方屏OLED规格书
08-20
本文将对0.96寸方屏OLED规格书进行详细的解读，涵盖规格书的各个方面，包括显示规格、机械规格、活动区域/存储器映射和像素构造、机械图纸、引脚定义、绝对极值、光学和电气特性、功能规格、可靠性测试、出货控制和...
中景园电子0.96OLED显示屏资料
06-19
《中景园电子0.96寸OLED显示屏资料详解》 在电子设计领域，OLED（Organic Light-Emitting Diode）显示屏因其高对比度、快速响应速度和低功耗特性，被广泛应用于各类智能设备中。本文将详细探讨中景园电子0.96寸OLED...
关于七针0.96寸OLED使用IIC接口的说明.pdf
11-01
### 七针0.96寸OLED使用IIC接口详解 #### 一、引言 随着物联网技术的发展，小型显示设备的需求日益增加。OLED（有机发光二极管）显示器因其轻薄、高对比度及自发光特性而受到广泛青睐。本文主要介绍一种常见的小型...
0.96寸OLED屏中文数据手册
03-14
中文参考手册
中景园0.96寸oled资料.zip
07-20
例如，使用SSD1306或SH1106驱动芯片的OLED屏，需要理解它们的命令集和数据格式。 对于STM32微控制器，其强大的处理能力和丰富的外设接口使其能高效地驱动OLED。开发者可以使用HAL库或LL库来操作I2C或SPI接口，然后...
基于stm32f103与IIC的0.96OLED屏幕显示字符与平滑滚动显示
被无情调岗的痛苦狗头
12-26 8723
基于stm32f103与IIC的0.96OLED屏幕驱动一、0.96OLED屏幕简介1、类型区分及接线2、IIC通信原理二、正常显示与平滑滚动显示1、显示字符2、显示传感器数据3、平滑滚动显示4、效果演示 一、0.96OLED屏幕简介 1、类型区分及接线 模块有7针和4针两种，下面的是7针模块，主要引脚与4针相同 2、IIC通信原理 关于IIC在之前的文章AHT20与stm32中介绍过，这里只做主要的时序介绍。 IIC总线 开始信号：处理器让SCL时钟保持高电平，然后让SDA数据信号由高变低就表
0.96寸OLED显示屏显示字符串、汉字（stm32HAL库）
qq_50749196的博客
06-03 1万+
OLED，即有机发光二极管OLED由于同时具备自发光，不需背光源、对比度高、厚度薄、视角广、反应速度快、可用于挠曲性面板、使用温度范围广、构造及制程较简单等优异之特性，被认为是下一代的平面显示器新兴应用技术。OLED显示其实说白了就是对于像素点的点亮和熄灭进行操作。本文采用的是4针的0.96寸OLED显示进行讲解，采用的是IIC协议，屏幕整体分辨率为128*64驱动芯片为SSD1306，下面是引脚功能介绍。0.96寸OLED屏幕显示引脚介绍名称注释GND电源地VCC电源正（3.3～5V）
0.96寸OLED贪吃蛇算法思路分享—代码开源—简单易懂超详细
qq_28145393的博客
06-25 2629
一个星期前，我把单片机带回了寝室，然后。。。就诞生了个小小的贪吃蛇小游戏程序 先提前说好，在这个函数中涉及到几个函数需要替换的清手动替换 OLED_Clear(); //oled清屏函数 OLED_Rect(); //oled画空心矩形函数 OLED_ShowString(); //oled显示字符串函数 OLED_DrawDot(); //oled描点函数 OLED_ShowNum(); //oled显示变量值函数 delay_ms();
基于STM32的0.96寸OLED显示屏显示数据
cleveryoga的博客
11-21 3681
文章目录一、SPI1.简介2.SPI 的物理层和协议层2.1物理层2.2协议层3.通讯引脚二、使用0.96寸OLED显示屏显示数据1.显示屏介绍2.题目要求三、显示学号和姓名1.工程建立2.编译测试3.电路连接4.结果 一、SPI 1.简介 SPI 协议是由摩托罗拉公司提出的通讯协议(Serial Peripheral Interface)，即串行外围设备接口，是一种高速全双工的通信总线。它被广泛地使用在 ADC、LCD 等设备与 MCU 间，要求通讯速率较高的场合。 2.SPI 的物理层和协议层 2.1物
0.96寸OLED12864屏幕控制（原理+代码）
RY_01的博客
04-09 1万+
对stm32f103芯片，控制0.96寸OLED12864屏幕，spi7针，驱动芯片为SSD1306，的详细操作原理讲解教程（含代码）及keil工程文件，可移植至51
一文教你点亮0.96寸OLED--SSD1315芯片（IIC方式）
qq_64690561的博客
11-13 6783
此部分属于设备与OLED沟通的“桥梁”，无论是数据还是指令，都需要这部分来支持。事实上，这部分也属于IIC协议的范畴。如果使用硬件IIC，则把写数据的方式改成硬件IIC的函数即可。这部分是对IO口的初始化（如果是硬件IIC，则不需要前面4句），作用是设置显示的方向，亮度，扫描方式，等等。此部分属于IIC协议的内容，（如果使用IO模拟IIC）只有IIC起始位，停止位，等待应答等；优点：可以任意画图，如一个点，矩形 ，圆形等。范围：x取（0,128），y取（0，63）顾名思义，方向翻转，颜色反转，息屏亮屏。
评论 33
添加红包

请填写红包祝福语或标题

个

红包个数最小为10个

元

红包金额最低5元

当前余额3.43元 前往充值 >
需支付：10.00元
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付元
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明：

1.余额是钱包充值的虚拟货币，按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载，可以购买VIP、付费专栏及课程。

余额充值