一:IP地址规划
Pc地址
设备 | 地址 | 网关 |
PC1 | 192.168.1.2/24 | 192.168.1.1/24 |
PC2 | 192.168.2.2/24 | 192.168.2.1/24 |
PC3 | 192.168.3.2/24 | 192.168.3.1/24 |
设备地址:
设备 | 接口 | 地址 |
R1 | S4/0/0 | 14.1.1.1/24 |
R2 | S4/0/0 | 34.1.1.1/24 |
R3 | S4/0/0 | 44.1.1.1/24 |
R4 | S4/0/0 | 14.1.1.2/24 |
S4/0/1 | 34.1.1.2/24 | |
S3/0/30 | 44.1.1.2/24 | |
Lookback0 | 5.5.5.5/24 |
二:配置IP地址
R1配置
[R1]int g0/0/0
[R1-GigabitEthernet0/0/0]ip add 192.168.1.1 24
[R1-GigabitEthernet0/0/0]int s 4/0/0
[R1-Serial4/0/0]ip add 14.1.1.1 24
R2配置(isp)
[R2]int s 4/0/0
[R2-Serial4/0/0]ip address 14.1.1.2 24
[R2-Serial4/0/0]int s 4/0/1
[R2-Serial4/0/1]ip address 34.1.1.2 24
[R2-Serial4/0/1]int s 3/0/0
[R2-Serial3/0/0]ip address 44.1.1.2 24
[R2-Serial3/0/0]q
[R2]int l 0
[R2-LoopBack0]ip address 5.5.5.5 24
R3配置
[R3]int g0/0/0
[R3-GigabitEthernet 0/0/0]ip add 192.168.2.1 24
[R3-GigabitEthernet 0/0/0]int s 4/0/0
[R3-Serial4/0/0]ip add 34.1.1.1 24
R4配置
[R4]int g0/0/0
[R4-GigabitEthernet 0/0/0]ip add 192.168.3.1 24
[R4-GigabitEthernet 0/0/0]int s 4/0/0
[R4-Serial4/0/0]ip add 44.1.1.1 24
三:配置缺省路由
[R1]ip route-static 0.0.0.0 0 14.1.1.2
[R3]ip route-static 0.0.0.0 0 34.1.1.2
[R4]ip route-static 0.0.0.0 0 44.1.1.2
四:NAT
[R1]acl 2000
[R1-acl-basic-2000]rule 1 permit source any
[R1-acl-basic-2000]q
[R1]int s 4/0/0
[R1-Serial4/0/0]nat outbound 2000
[R3]acl 2000
[R3-acl-basic-2000]rule 1 permit source any
[R3-acl-basic-2000]q
[R3]int s 4/0/0
[R3-Serial4/0/0]nat outbound 2000
[R4]acl 2000
[R4-acl-basic-2000]rule 1 permit source any
[R4-acl-basic-2000]q
[R4]int s 4/0/0
[R4-Serial4/0/0]nat outbound 2000
五:HDLC封装
[R1]int s 4/0/0
[R1-Serial4/0/0]link-protocol hdlc
[R2]int s 4/0/0
[R2-Serial4/0/0]link-protocol hdlc
六:PAP认证
主认证方配置
[R2]aaa
[R2-aaa]local-user huawei password cipher huawei
[R2-aaa]local-user huawei service-type ppp
[R2]int s 4/0/1
[R2-Serial4/0/1]ppp authentication-mode pap
被认证方配置
[R3]int s 4/0/0
[R3-Serial4/0/0]ppp pap local-user huawei
七:chap认证
主认证方配置
[R2]aaa
[R2-aaa]local-user huawei password cipher huawei
[R2-aaa]local-user huawei service-type ppp
[R2]int s 3/0/0
[R2-Serial3/0/0]ppp authentication-mode chap
被认证方配置
[R4]int s 4/0/0
[R4-Serial4/0/0]ppp chap user huawei
[R4-Serial4/0/0]ppp chap password cipher huawei
八:R1,R2,R3搭建MGRE环境
R1配置
[R1]int Tunnel 0/0/0
[R1-Tunnel0/0/0]ip add 10.1.1.1 24
[R1-Tunnel0/0/0]tunnel-protocol gre p2mp
[R1-Tunnel0/0/0]source 14.1.1.1
[R1-Tunnel0/0/0]nhrp network-id 100
R3配置
[R3]int Tunnel 0/0/0
[R3-Tunnel0/0/0]ip add 10.1.1.3 24
[R3-Tunnel0/0/0]tunnel-protocol gre p2mp
[R3-Tunnel0/0/0]source s 4/0/0
[R3-Tunnel0/0/0]nhrp network-id 100
[R3-Tunnel0/0/0]nhrp entry 10.1.1.1 14.1.1.1 register
R4配置
[R4]int Tunnel 0/0/0
[R4-Tunnel0/0/0]ip add 10.1.1.4 24
[R4-Tunnel0/0/0]tunnel-protocol gre p2mp
[R4-Tunnel0/0/0]source s 4/0/0
[R4-Tunnel0/0/0]nhrp network-id 100
[R4-Tunnel0/0/0]nhrp entry 10.1.1.1 14.1.1.1 register
九:书写RIP路由
R1配置
[R1]rip 1
[R1-rip-1]version 2
[R1-rip-1]network 192.168.1.0
[R1-rip-1]network 10.0.0.0
[R1-rip-1]q
[R1]int Tunnel 0/0/0
[R1-Tunnel0/0/0]nhrp entry multicast dynamic
[R1-Tunnel0/0/0]undo rip split-horizon
R3配置
[R3]rip 1
[R3-rip-1]version
[R3-rip-1]network 192.168.2.0
[R3-rip-1]network 10.0.0.0
R4配置
[R4]rip 1
[R4-rip-1]version 2
[R4-rip-1]network 192.168.3.0
[R4-rip-1]network 10.0.0.0
十测试