描述:
Ethtool是用于查询及设置网卡参数的命令。
概要:
ethtool ethX //查询ethX网口基本设置
ethtool –h //显示ethtool的命令帮助(help)
ethtool –i ethX //查询ethX网口的相关信息
ethtool –d ethX //查询ethX网口注册性信息
ethtool –r ethX //重置ethX网口到自适应模式
ethtool –S ethX //查询ethX网口收发包统计
ethtool –s ethX [speed 10|100|1000]/ //设置网口速率10/100/1000M
[duplex half|full]/ //设置网口半/全双工
[autoneg on|off]/ //设置网口是否自协商
[port tp|aui|bnc|mii]/ //设置网口类型
[phyad N]/
[xcvr internal|exteral]/
[wol p|u|m|b|a|g|s|d...]/
[sopass xx:yy:zz:aa:bb:cc]/
[msglvl N]
举例:
1)[root@linux /]# ethtool eth1
Settings for eth1:
Supported ports: [ TP ]
Supported link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Supports auto-negotiation: Yes
Advertised link modes: 10baseT/Half 10baseT/Full
100baseT/Half 100baseT/Full
1000baseT/Full
Advertised auto-negotiation: Yes
Speed: 1000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: on
Supports Wake-on: umbg
Wake-on: d
Link detected: yes
2)[root@linux /]# ethtool -i eth1
driver: e1000
version: 5.0.43-k1
firmware-version: N/A
bus-info: 06:08.1
3)[root@linux /]# ethtool -S eth1
NIC statistics:
rx_packets: 58068300
tx_packets: 87124083
rx_bytes: 1589713008
tx_bytes: 2165825901
rx_errors: 0
tx_errors: 0
rx_dropped: 0
tx_dropped: 0
multicast: 0
collisions: 0
rx_length_errors: 0
rx_over_errors: 0
rx_crc_errors: 0
rx_frame_errors: 0
rx_fifo_errors: 0
rx_missed_errors: 0
tx_aborted_errors: 0
tx_carrier_errors: 0
tx_fifo_errors: 0
tx_heartbeat_errors: 0
tx_window_errors: 0
4)[root@linux /]# ethtool -s eth1 autoneg off speed 100 duplex full
相关:
1)[root@linux /]# which ethtool
/sbin/ethtool
2)[root@linux /]# rpm -qf /sbin/ethtool
ethtool-1.6-5
3)怎样使ethtool设置永久保存在网络设备中?
解决方法一:
ethtool设置可通过/etc/sysconfig/network-scripts/ifcfg-ethX文件保存,从而在设备下次启动时激活选项。
例如:ethtool -s eth0 speed 100 duplex full autoneg off
此指令将eth0设备设置为全双工自适应,速度为100Mbs。若要eth0启动时设置这些参数, 修改文件/etc/sysconfig/network-scripts/ifcfg-eth0 ,添加如下一行:
ETHTOOL_OPTS="speed 100 duplex full autoneg off"
解决方法二:
将ethtool设置写入/etc/rc.d/rc.local之中。