在ENSP环境下的静态路由综合实验

最新推荐文章于 2024-01-20 21:50:15 发布
最新推荐文章于 2024-01-20 21:50:15 发布
阅读量504 收藏 4
点赞数 1
文章标签： 大数据
版权声明：本文为博主原创文章，遵循 CC 4.0 BY-SA 版权协议，转载请附上原文出处链接和本声明。
本文链接：https://blog.csdn.net/gyuguyfdsd/article/details/125701457
版权
这是一个关于配置华为路由器的实验，涉及IP地址分配、环回接口设置、静态路由及默认路由的配置，以实现网络连接和避免环路问题。实验中使用了5台3260路由器，并通过GigabitEthernet接口进行互连，确保了各节点间的通信。
摘要由CSDN通过智能技术生成

实验拓扑如下图

 实验器材：5台3260路由器

 将IP划分好之后，就是配置各个路由器了，配置代码如下：

AR1：


<Huawei>sys	
<Huawei>system-view 
Enter system view, return user view with Ctrl+Z.
[Huawei]int lo	
[Huawei]int LoopBack 0
[Huawei-LoopBack0]ip ad	
[Huawei-LoopBack0]ip address 192.168.1.33 28
[Huawei-LoopBack0]
[Huawei-LoopBack0]
[Huawei-LoopBack0]q
[Huawei]int lo	
[Huawei]int LoopBack 1
[Huawei-LoopBack1]ip ad	
[Huawei-LoopBack1]ip address 192.168.1.49 28
[Huawei-LoopBack1]q
[Huawei]int	
[Huawei]interface g0/0/0
[Huawei-GigabitEthernet0/0/0]ip ad	
[Huawei-GigabitEthernet0/0/0]ip address 192.168.1.1 30
[Huawei-GigabitEthernet0/0/0]q
[Huawei]int	
[Huawei]interface g0/0/1
[Huawei-GigabitEthernet0/0/1]ip ad	
[Huawei-GigabitEthernet0/0/1]ip address 192.168.1.5 30
[Huawei-GigabitEthernet0/0/1]q
[Huawei]dis	
[Huawei]display ip int	
[Huawei]display ip interface b	
[Huawei]display ip interface brief 
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 5
The number of interface that is DOWN in Physical is 1
The number of interface that is UP in Protocol is 5
The number of interface that is DOWN in Protocol is 1

Interface                         IP Address/Mask      Physical   Protocol  
GigabitEthernet0/0/0              192.168.1.1/30       up         up        
GigabitEthernet0/0/1              192.168.1.5/30       up         up        
GigabitEthernet0/0/2              unassigned           down       down      
LoopBack0                         192.168.1.33/28      up         up(s)     
LoopBack1                         192.168.1.49/28      up         up(s)     
NULL0                             unassigned           up         up(s)     
[Huawei]
//以上为配置各个端口以及环回地址
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]ip rot	
[Huawei]ip rou	
[Huawei]ip route-s	
[Huawei]ip route-static 0.0.0.0 0 192.168.1.2
[Huawei]ip route-static 0.0.0.0 0 192.168.1.6
//以上两条为缺省路由，为解决第二个问题
[Huawei]ip ro	
[Huawei]ip route-s	
[Huawei]ip route-static 192.168.1.64 27 192.168.1.2
[Huawei]ip route-static 192.168.1.8 30 192.168.1.2
[Huawei]ip route-static 192.168.1.128 27 192.168.1.2
[Huawei]ip route-static 192.168.1.128 27 192.168.1.6
[Huawei]ip route-static 192.168.1.16 30 192.168.1.2
[Huawei]
[Huawei]ip route-static 192.168.1.16 30 192.168.1.6
[Huawei]ip route-static 192.168.1.12 30 192.168.1.6
[Huawei]ip route-static 192.168.1.96 27 192.168.1.6
//以上为配置静态路由
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]ip ro	
[Huawei]ip route-s	
[Huawei]ip route-static 192.168.1.32 27 null 0
//以上为避免环路问题

AR2：

<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]int ;o	
[Huawei]int lo	
[Huawei]int LoopBack 0
[Huawei-LoopBack0]ip ad	
[Huawei-LoopBack0]ip address 192.168.1.65 28
[Huawei-LoopBack0]q
[Huawei]int lo	
[Huawei]int LoopBack 1
[Huawei-LoopBack1]ip ad	
[Huawei-LoopBack1]ip address 192.168.1.81 28
[Huawei-LoopBack1]q
[Huawei]int	
[Huawei]interface g0/0/0
[Huawei-GigabitEthernet0/0/0]ip ad	
[Huawei-GigabitEthernet0/0/0]ip address 192.168.1.2 30
Jul 10 2022 01:11:29-08:00 Huawei %%01IFNET/4/LINK_STATE(l)[0]:The line protocol
 IP on the interface GigabitEthernet0/0/0 has entered the UP state. 
[Huawei-GigabitEthernet0/0/0]q
[Huawei]int	
[Huawei]interface g0/0/1
[Huawei-GigabitEthernet0/0/1]ip ad	
[Huawei-GigabitEthernet0/0/1]ip address 192.168.1.9 30
Jul 10 2022 01:11:55-08:00 Huawei %%01IFNET/4/LINK_STATE(l)[1]:The line protocol
 IP on the interface GigabitEthernet0/0/1 has entered the UP state. 
[Huawei-GigabitEthernet0/0/1]q
[Huawei]dis	
[Huawei]display ip int	
[Huawei]display ip interface b	
[Huawei]display ip interface brief 
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 5
The number of interface that is DOWN in Physical is 1
The number of interface that is UP in Protocol is 5
The number of interface that is DOWN in Protocol is 1

Interface                         IP Address/Mask      Physical   Protocol  
GigabitEthernet0/0/0              192.168.1.2/30       up         up        
GigabitEthernet0/0/1              192.168.1.9/30       up         up        
GigabitEthernet0/0/2              unassigned           down       down      
LoopBack0                         192.168.1.65/28      up         up(s)     
LoopBack1                         192.168.1.81/28      up         up(s)     
NULL0                             unassigned           up         up(s)     
[Huawei]
//配置各个端口及环回
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]
[Huawei]ip ro	
[Huawei]ip route-s	
[Huawei]ip route-static 0.0.0.0 0 192.168.1.10
//缺省路由
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]ip ro	
[Huawei]ip route-s	
[Huawei]ip route-static 192.168.1.32 27 192.168.1.5
[Huawei]ip route-static 192.168.1.0 30 192.168.1.5
[Huawei]ip route-static 192.168.1.64 27 192.168.1.5
[Huawei]ip route-static 192.168.1.64 27 192.168.1.14
[Huawei]ip route-static 192.168.1.16 30 192.168.1.10
[Huawei]ip route-static 192.168.1.128 27 192.168.1.10
[Huawei]ip route-static 192.168.1.12 30 192.168.1.10
[Huawei]ip route-static 192.168.1.96 27 192.168.1.10
[Huawei]ip route-static 192.168.1.96 27 192.168.1.1
[Huawei]ip route-static 192.168.1.4 30 192.168.1.1
[Huawei]ip route-static 192.168.1.32 27 192.168.1.1
[Huawei]

 //静态路由
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]ip route-static 192.168.1.32 27 null 0
[Huawei]
[Huawei]undo ip route-static 192.168.1.32 27 null 0
[Huawei]ip ro	
[Huawei]ip route-s	
[Huawei]ip route-static 192.168.1.64 27 null 0

//避免环路
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]int ;o	
[Huawei]int lo	
[Huawei]int LoopBack 0
[Huawei-LoopBack0]ip ad	
[Huawei-LoopBack0]ip address 192.168.1.65 28
[Huawei-LoopBack0]q
[Huawei]int lo	
[Huawei]int LoopBack 1
[Huawei-LoopBack1]ip ad	
[Huawei-LoopBack1]ip address 192.168.1.81 28
[Huawei-LoopBack1]q
[Huawei]int	
[Huawei]interface g0/0/0
[Huawei-GigabitEthernet0/0/0]ip ad	
[Huawei-GigabitEthernet0/0/0]ip address 192.168.1.2 30
Jul 10 2022 01:11:29-08:00 Huawei %%01IFNET/4/LINK_STATE(l)[0]:The line protocol
 IP on the interface GigabitEthernet0/0/0 has entered the UP state. 
[Huawei-GigabitEthernet0/0/0]q
[Huawei]int	
[Huawei]interface g0/0/1
[Huawei-GigabitEthernet0/0/1]ip ad	
[Huawei-GigabitEthernet0/0/1]ip address 192.168.1.9 30
Jul 10 2022 01:11:55-08:00 Huawei %%01IFNET/4/LINK_STATE(l)[1]:The line protocol
 IP on the interface GigabitEthernet0/0/1 has entered the UP state. 
[Huawei-GigabitEthernet0/0/1]q
[Huawei]dis	
[Huawei]display ip int	
[Huawei]display ip interface b	
[Huawei]display ip interface brief 
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 5
The number of interface that is DOWN in Physical is 1
The number of interface that is UP in Protocol is 5
The number of interface that is DOWN in Protocol is 1

Interface                         IP Address/Mask      Physical   Protocol  
GigabitEthernet0/0/0              192.168.1.2/30       up         up        
GigabitEthernet0/0/1              192.168.1.9/30       up         up        
GigabitEthernet0/0/2              unassigned           down       down      
LoopBack0                         192.168.1.65/28      up         up(s)     
LoopBack1                         192.168.1.81/28      up         up(s)     
NULL0                             unassigned           up         up(s)     
[Huawei]


<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]
[Huawei]ip ro	
[Huawei]ip route-s	
[Huawei]ip route-static 0.0.0.0 0 192.168.1.10
//缺省路由
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]ip ro	
[Huawei]ip route-s	
[Huawei]ip route-static 192.168.1.32 27 192.168.1.5
[Huawei]ip route-static 192.168.1.0 30 192.168.1.5
[Huawei]ip route-static 192.168.1.64 27 192.168.1.5
[Huawei]ip route-static 192.168.1.64 27 192.168.1.14
[Huawei]ip route-static 192.168.1.16 30 192.168.1.10
[Huawei]ip route-static 192.168.1.128 27 192.168.1.10
[Huawei]ip route-static 192.168.1.12 30 192.168.1.10
[Huawei]ip route-static 192.168.1.96 27 192.168.1.10
[Huawei]ip route-static 192.168.1.96 27 192.168.1.1
[Huawei]ip route-static 192.168.1.4 30 192.168.1.1
[Huawei]ip route-static 192.168.1.32 27 192.168.1.1
//静态路由
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]ip route-static 192.168.1.32 27 null 0
[Huawei]
[Huawei]undo ip route-static 192.168.1.32 27 null 0
[Huawei]ip ro	
[Huawei]ip route-s	
[Huawei]ip route-static 192.168.1.64 27 null 0
//以上避免环路问题

AR3：

<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]int lo	
[Huawei]int LoopBack 0
[Huawei-LoopBack0]ip ad
                        ^
Error:Incomplete command found at '^' position.
[Huawei-LoopBack0]ip ad	
[Huawei-LoopBack0]ip address 192.168.1.97 28
[Huawei-LoopBack0]q
[Huawei]int lo	
[Huawei]int LoopBack 1
[Huawei-LoopBack1]ip ad	
[Huawei-LoopBack1]ip address 192.168.1.113 28
[Huawei-LoopBack1]q
[Huawei]int 	
[Huawei]interface g0/0/0
[Huawei-GigabitEthernet0/0/0]ip ad	
[Huawei-GigabitEthernet0/0/0]ip address 192.168.1.6 30
Jul 10 2022 01:13:57-08:00 Huawei %%01IFNET/4/LINK_STATE(l)[0]:The line protocol
 IP on the interface GigabitEthernet0/0/0 has entered the UP state. 
[Huawei-GigabitEthernet0/0/0]q
[Huawei]int	
[Huawei]interface g0/0/1
[Huawei-GigabitEthernet0/0/1]ip ad	
[Huawei-GigabitEthernet0/0/1]ip address 192.168.1.13 30
[Huawei-GigabitEthernet0/0/1]
Jul 10 2022 01:14:22-08:00 Huawei %%01IFNET/4/LINK_STATE(l)[1]:The line protocol
 IP on the interface GigabitEthernet0/0/1 has entered the UP state. 
[Huawei-GigabitEthernet0/0/1]q
[Huawei]dis	
[Huawei]display ip int	
[Huawei]display ip interface b	
[Huawei]display ip interface brief 
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 5
The number of interface that is DOWN in Physical is 1
The number of interface that is UP in Protocol is 5
The number of interface that is DOWN in Protocol is 1

Interface                         IP Address/Mask      Physical   Protocol  
GigabitEthernet0/0/0              192.168.1.6/30       up         up        
GigabitEthernet0/0/1              192.168.1.13/30      up         up        
GigabitEthernet0/0/2              unassigned           down       down      
LoopBack0                         192.168.1.97/28      up         up(s)     
LoopBack1                         192.168.1.113/28     up         up(s)     
NULL0                             unassigned           up         up(s)     
[Huawei]
//端口配置
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]ip ro	
[Huawei]ip route-s	
[Huawei]ip route-static 0.0.0.0 0 192.168.1.14
//缺省路由
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]ip ro	
[Huawei]ip route-s	
[Huawei]ip route-static 192.168.1.32 27 192.168.1.5
[Huawei]ip route-static 192.168.1.0 30 192.168.1.5
[Huawei]ip route-static 192.168.1.64 27 192.168.1.5
[Huawei]ip route-static 192.168.1.64 27 192.168.1.14
[Huawei]ip route-static 192.168.1.8 30 192.168.1.14
[Huawei]ip route-static 192.168.1.128 27 192.168.1.14
[Huawei]ip route-static 192.168.1.16 30 192.168.1.14
 //静态路由
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]ip ro	
[Huawei]ip route-s	
[Huawei]ip rou	
[Huawei]ip route-s	
[Huawei]ip route-static 192.168.1.96 27 null 0
//避免环路

AR4：

<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]int lo	
[Huawei]int LoopBack 0
[Huawei-LoopBack0]ip ad	
[Huawei-LoopBack0]ip address 192.168.1.129 28
[Huawei-LoopBack0]q
[Huawei]int lo	
[Huawei]int LoopBack 1
[Huawei-LoopBack1]ip ad	
[Huawei-LoopBack1]ip address 192.168.1.145 28
[Huawei-LoopBack1]q
[Huawei]int	
[Huawei]interface g0/0/0
[Huawei-GigabitEthernet0/0/0]ip ad	
[Huawei-GigabitEthernet0/0/0]ip address 192.168.1.14 30
Jul 10 2022 01:17:14-08:00 Huawei %%01IFNET/4/LINK_STATE(l)[0]:The line protocol
 IP on the interface GigabitEthernet0/0/0 has entered the UP state. 
[Huawei-GigabitEthernet0/0/0]q
[Huawei]int	
[Huawei]interface g0/0/1
[Huawei-GigabitEthernet0/0/1]ip ad	
[Huawei-GigabitEthernet0/0/1]ip address 192.168.1.10 30
[Huawei-GigabitEthernet0/0/1]
Jul 10 2022 01:17:58-08:00 Huawei %%01IFNET/4/LINK_STATE(l)[1]:The line protocol
 IP on the interface GigabitEthernet0/0/1 has entered the UP state. 
[Huawei-GigabitEthernet0/0/1]q
[Huawei]int	
[Huawei]interface g0/0/2
[Huawei-GigabitEthernet0/0/2]ip ad	
[Huawei-GigabitEthernet0/0/2]ip address 192.168.1.21 30
[Huawei-GigabitEthernet0/0/2]
Jul 10 2022 01:18:35-08:00 Huawei %%01IFNET/4/LINK_STATE(l)[2]:The line protocol
 IP on the interface GigabitEthernet0/0/2 has entered the UP state. 
[Huawei-GigabitEthernet0/0/2]q
[Huawei]int	
[Huawei]interface g4/0/0
[Huawei-GigabitEthernet4/0/0]ip ad	
[Huawei-GigabitEthernet4/0/0]ip address 192.168.1.17 30
[Huawei-GigabitEthernet4/0/0]
Jul 10 2022 01:19:10-08:00 Huawei %%01IFNET/4/LINK_STATE(l)[3]:The line protocol
 IP on the interface GigabitEthernet4/0/0 has entered the UP state. 
[Huawei-GigabitEthernet4/0/0]q
[Huawei]dis	
[Huawei]display ip int	
[Huawei]display ip interface b	
[Huawei]display ip interface brief 
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 7
The number of interface that is DOWN in Physical is 0
The number of interface that is UP in Protocol is 7
The number of interface that is DOWN in Protocol is 0

Interface                         IP Address/Mask      Physical   Protocol  
GigabitEthernet0/0/0              192.168.1.14/30      up         up        
GigabitEthernet0/0/1              192.168.1.10/30      up         up        
GigabitEthernet0/0/2              192.168.1.21/30      up         up        
GigabitEthernet4/0/0              192.168.1.17/30      up         up        
LoopBack0                         192.168.1.129/28     up         up(s)     
LoopBack1                         192.168.1.145/28     up         up(s)     
NULL0                             unassigned           up         up(s)     
[Huawei]
//端口配置
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]ip ro	
[Huawei]ip route-s	
[Huawei]ip route-static 0.0.0.0 0 192.168.1.18
[Huawei]
//缺省路由
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]ip	
[Huawei]ip ro	
[Huawei]ip route-static 192.168.1.96 27 192.168.1.13
[Huawei]ip route-static 192.168.1.4 30 192.168.1.13
[Huawei]ip route-static 192.168.1.32 27 192.168.1.13
[Huawei]ip route-static 192.168.1.32 27 192.168.1.9
[Huawei]ip route-static 192.168.1.0 30 192.168.1.9
[Huawei]ip route-static 192.168.1.64 27 192.168.1.9
[Huawei]

 //静态路由
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]ip rou	
[Huawei]ip route-s	
[Huawei]ip route-static 0.0.0.0 0 192.168.1.128 27 null 0

  //避免环路
[Huawei]ip route-static 0.0.0.0 0 192.168.1.22 preference 61
//AR4配置缺省路由优先级
[Huawei]interface GigabitEtherent 4/0/0
[Huawei-GigabitEtherent 4/0/0]shutdown
//断掉4/0/0接口

 AR5：

[Huawei]display ip interface brief 
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 4
The number of interface that is DOWN in Physical is 1
The number of interface that is UP in Protocol is 4
The number of interface that is DOWN in Protocol is 1

Interface                         IP Address/Mask      Physical   Protocol  
GigabitEthernet0/0/0              192.168.1.22/30      up         up        
GigabitEthernet0/0/1              192.168.1.18/30      up         up        
GigabitEthernet0/0/2              unassigned           down       down      
LoopBack0                         5.5.5.5/24           up         up(s)     
NULL0                             unassigned           up         up(s)     


//端口
[Huawei]ip route-static 192.168.1.4 255.255.255.255 192.168.1.21 preference 61
[Huawei]ip route-static 192.168.1.8 255.255.255.255 192.168.1.21 preference 61
[Huawei]ip route-static 192.168.1.12 255.255.255.255 192.168.1.21 preference 61
[Huawei]ip route-static 192.168.1.32 255.255.255.255 192.168.1.21 preference 61
[Huawei]ip route-static 192.168.1.64 255.255.255.255 192.168.1.21 preference 61
[Huawei]ip route-static 192.168.1.96 255.255.255.255 192.168.1.21 preference 61
[Huawei]ip route-static 192.168.1.128 255.255.255.255 192.168.1.21 preference 61
//AR5向AR4的通信备份

 然后开始测试：

 

 成功，则此次试验结束

 

 

三秋鱼籽
关注
  • 1
    点赞
  • 踩
  • 4
    收藏
    觉得还不错? 一键收藏
  • 0
    评论
静态路由概述与实验（使用华为eNSP）：静态路由配置实验、负载分担实验、路由备份实验
weixin_44904418的博客
07-28 1826
主要内容为静态路由概述与实验。 做了三个实验，分别为静态路由配置实验、负载分担实验、路由备份实验。 其中路由备份实验有多种验证方式。
华为交换机ENSP实验静态路由.topo
04-28
ENSP静态路由实验，两台交换机不同网段间互通。适用于高速行业收费及监控网络。新手必回技能。配置简单，适用性强。
综合组网实验(eNSP)(vlan、vlan间通信、nat地址转换、acl、dhcp、ospf……)
01-09
综合组网实验 一、概述 本次实验模拟学校实验室的网络环境，通过虚拟环境进行组网，通过vlan、路由、访问控制等，实现不同实验室之间的通信，并且可以通过ACL控制某一个实验室的网络通信，进行简单的组网分析 二、应用的网络知识 Vlan Vlan间通信 静态路由 动态路由 链路聚合 链路备份 Nat地址转换 ACL访问控制 DHCP 三、实验拓扑 四、实验分析 五、实验详细配置 1. LSW1的配置 1.1 划分vlan 将G0/0/1接口划入vlan201，G0/0/2接口划入vlan202 sys Enter system view, return user view with Ctrl+Z
ensp静态路由综合实验
weixin_54494152的博客
07-12 975
实验要求： 1.除R5的换回地址固定以外，整个其他所有网段基于192.168.1.0/ 24进行合理的IP地址划分 2.R1~R4每个路由器存在两个换回接口，用于模拟链接PC网段；地址也在192.168.1.0/24这个网络范围内1. 3.R1~R4上不能直接编写到达5.5.5.0/24的静态路由，但依然可以访问 4.全网可达，尽量减少每台路由器，路由表条目的数量，避免环路出现 5.R4与R5间，正常1000M链路通信，故障时自动改为100M 实验分析： 1.数广播域，根据广播域进行子
eNSP静态路由综合实验
MorningStar_He的博客
12-12 3237
实验要求： 分析： 1.首先进行子网划分 2.创建环回接口，分配划分好的子网 3.用缺省路由完成要求三 4.用浮动静态路由完成要求五 实验步骤： 先来子网划分，如图所示
华为eNSP静态路由项配置实验报告（网络技术基础与计算思维实验教程）
11-17
**华为eNSP静态路由项配置实验报告** 本实验报告主要针对华为eNSP平台，旨在帮助软件工程专业学生理解并掌握网络技术基础，特别是静态路由配置和IP分组的逐跳转发过程。实验旨在通过实际操作提升对路由器静态路由...
ENSP构建静态路由综合实验-HCIP
07-21
### ENSP构建静态路由综合实验-HCIP #### 实验目的 本次实验旨在通过静态路由配置，实现私网与公网的互联互通。实验不仅要求完成基本的网络连接设置，还涉及了高级配置，如子网汇总、防环路、黑洞路由等，确保网络...
ENSP构建静态路由综合实验
最新发布
07-23
### ENSP构建静态路由综合实验知识点解析 #### 实验目的 本次实验旨在通过构建一个包含静态路由的网络环境，让参与者深入理解静态路由的工作原理及其配置方法。实验重点在于如何设计合理的网络拓扑结构、分配IP地址...
eNSP静态路由的综合实验
qq_34267076的博客
09-22 1565
要求： 1.R6为isp，接口IP地址为公有地址，该设备只能配置IP地址，之后不能再对其进行其他任何配置； 2.R1-R5为局域网，私有IP地址192.168.1.0/24，请合理分配; 3.R1，R2,R4,各有两个环回地址；R5，R6各有一个环回地址；所有路由器上环回均代表连接用户的接口； 4.R3下的两台PC通过DHCP自动获取IP地址； 5.选路最佳，路由表尽量小，避免环路； 6.R1-R5均可以访问R6的环回； 7.R6 telnet R5 的公有IP地址时，实际登录到R1上； 8.R4与R5正.
HCIA/HCIP使用eNSP模拟路由综合实验
skawngur111的博客
11-25 2471
使用eNSP模拟路由综合实验 路由综合 目录使用eNSP模拟路由综合实验拓扑预览一、配置RIP区域（粉色）1.配置R2 g0/0/0与回环口并宣告路由2.配置R1 g0/0/0 g0/0/1并宣告路由3.测试二、配置OSPF区域（黄色）1.配置R42.配置R53.配置R64.配置R75.路由宣告网段的计算 与 反掩码的计算6.测试三、配置静态区域（蓝色）1.配置静态路由2.在R4中发布缺省路由3.配置R3配置完成 开始测试 拓扑预览 拓扑配置如图所示 要求： 1.R1 R2 配置RIP 2.R4 R
静态路由综合实验
qq_45491497的博客
11-24 497
题目要求及拓扑搭建如下：###### 1.规划IP地址 借2位规划出四个网段分别是： 192.168.1.0/26，192.168.1.64/26， 192.168.1.128/26，192.168.1.192/26 <1>其中192.168.1.0/26——用于骨干链路（即AR1,AR2,AR3之间） 借4位划分出16个网段，我们取前三个： 192.168.1.0/30，192.16...
eNSP 静态路由综合实验
aihua002的博客
01-12 639
可划分为五个大网段，分别为r1-r4的4个回环网段和主干网段一个。每个大的回环网段又可划分为2个小的回环网段。一个大的主干网段又可划分为6个小的主干网段。
ensp之静态路由综合实验
AXDRXS的博客
08-03 851
192.168.1.0/27 1.0/30 1.4/30 1.8/30 1.12/30 1.16/30 1.20/30 1.24/30 1.28/30 划分主干道网段。IP地址配置、环回地址配置、合理进行子网汇总、缺省路由、空路由接口、浮动静态路由、ACL表规则撰写、动态NAT网络地址转换、端口映射、远程登陆。写静态路由时，两个环回直接汇总为一条，减少路由条目，合理利用空路由接口，避免环路。每一台路由器上通过缺省对外网进行流量访问，再补充静态路由实现内网全网可达。
eNSP—综合实验
m0_46237205的博客
10-28 5942
实验拓扑图如下： LSW2的配置： <Huawei>sys [Huawei]undo info-center enable [Huawei]sysname LSW1 [LSW2]vlan batch 10 20 [LSW2]int g0/0/1 [LSW2-GigabitEthernet0/0/1]port link-type access [LSW2-GigabitEthernet0/0/1]port default vlan 10 [LSW2-GigabitEthernet0/0/1
静态路由ensp实验
my963510803的博客
06-09 2158
实验： 1.除R5的环回地址已固定外，整个其他所有的网段基于192.168.1.0/24 进行合理的IP地址划分 2.R1-R4每个路由器存在两个环回接口，用于模拟连接PC的网段，地址也在192.168.1.0/24这个网络范围 3.R1-R4上不能直接编写到达5.5.5.0/24的静态路由，但依然可以访问 4.全网可达，尽量减少每台路由器，路由表条目的数量，避免环路出现 5.R4与R5间，正常1000M链路通信，故障时自动改为100M R4右键设置关机后添加端口 1.IP地址规划.
eNSP静态综合试验（作业）
xzqyydds的博客
07-10 1979
eNSP静态综合试验（作业）
HCIA（终）eNSP网络基础综合实验：静态路由、OSPF动态路由、Telnet连接、NAT地址转换、ACL规则配置
Superstacks超全栈
01-20 2393
eNSP(Enterprise Network Simulation Platform)是一款由华为提供的、可扩展的、图形化操作的网络仿真工具平台，主要对企业网络路由器、交换机进行软件仿真，完美呈现真实设备实景，支持大型网络模拟，让广大用户有机会在没有真实设备的情况下能够模拟演练，学习网络技术。高度仿真 可模拟华为AR路由器、x7系列交换机的大部分特性。 可模拟PC终端、Hub、云、帧中继交换机等。 仿真设备配置功能，快速学习华为命令行。 可模拟大规模设备组网。 可通过真实网卡实现与真实网络设备的对接。
使用华为ensp模拟器实现静态路由综合实验
weixin_75192377的博客
08-03 307
【代码】使用华为ensp模拟器实现静态路由综合实验。
评论
添加红包

请填写红包祝福语或标题

个

红包个数最小为10个

元

红包金额最低5元

当前余额3.43元 前往充值 >
需支付：10.00元
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付元
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明：

1.余额是钱包充值的虚拟货币，按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载，可以购买VIP、付费专栏及课程。

余额充值