存储-配置多路径

                                           Multipath

多路径软件作用：

1）冗余.为了保证存储访问的可靠性,一般至少需要用2块光纤卡,通过2个FC switch,接在磁盘阵列的两个控制器上.当一条路径出现问题,还有另一条路径可以访问.

2）负载均衡.既然有2个path，那么如果某一个path只是备用就浪费了.所以MultiPathing的软件的另一个功能就是load balance（也称为Active/Active）.但这个功能不仅仅由MultiPathing软件实现，磁盘阵列本身也必需支持，否则，MultiPathing只能实现主备方式（Active/Passive）.

 

创建multipath.conf文档,添加如下内容：

# This is a basic configuration file with some examples, for device mapper
# multipath.
# For a complete list of the default configuration values, see
# /usr/share/doc/device-mapper-multipath-0.4.7/multipath.conf.defaults
# For a list of configuration options with descriptions, see
# /usr/share/doc/device-mapper-multipath-0.4.7/multipath.conf.annotated

# Blacklist all devices by default. Remove this to enable multipathing
# on the default devices.
blacklist {
#        devnode "*"          --要注释掉* 
}

## By default, devices with vendor = "IBM" and product = "S/390.*" are
## blacklisted. To enable mulitpathing on these devies, uncomment the
## following lines.
#blacklist_exceptions {
# device {
#  vendor "IBM"
#  product "S/390.*"
# }
#}

## Use user friendly names, instead of using WWIDs as names.
defaults {
 user_friendly_names yes
}
##
## Here is an example of how to configure some standard options.
##
#
#defaults {
# udev_dir  /dev
# polling_interval  10
# selector  "round-robin 0"
# path_grouping_policy multibus
# getuid_callout  "/sbin/scsi_id -g -u -s /block/%n"
# prio_callout  /bin/true
# path_checker  readsector0
# rr_min_io  100
# max_fds   8192
# rr_weight  priorities
# failback  immediate
# no_path_retry  fail
# user_friendly_names yes
#}
##
## The wwid line in the following blacklist section is shown as an example
## of how to blacklist devices by wwid.  The 2 devnode lines are the
## compiled in default blacklist. If you want to blacklist entire types
## of devices, such as all scsi devices, you should use a devnode line.
## However, if you want to blacklist specific devices, you should use
## a wwid line.  Since there is no guarantee that a specific device will
## not change names on reboot (from /dev/sda to /dev/sdb for example)
## devnode lines are not recommended for blacklisting specific devices.
##
#blacklist {
#       wwid 26353900f02796769
# devnode "^(ram|raw|loop|fd|md|dm-|sr|scd|st)[0-9]*"
# devnode "^hd[a-z]"
#}
#multipaths {
# multipath {
#  wwid   3600508b4000156d700012000000b0000
#  alias   yellow
#  path_grouping_policy multibus
#  path_checker  readsector0
#  path_selector  "round-robin 0"
#  failback  manual
#  rr_weight  priorities
#  no_path_retry  5
# }
# multipath {
#  wwid   1DEC_____321816758474
#  alias   red
# }
#}
#devices {
# device {
#  vendor   "COMPAQ  "
#  product   "HSV110 (C)COMPAQ"
#  path_grouping_policy multibus
#  getuid_callout          "/sbin/scsi_id -g -u -s /block/%n"
#  path_checker  readsector0
#  path_selector  "round-robin 0"
#  hardware_handler "0"
#  failback  15
#  rr_weight  priorities
#  no_path_retry  queue
# }
# device {
#  vendor   "COMPAQ  "
#  product   "MSA1000         "
#  path_grouping_policy multibus
# }
#}

将multipath.conf文件放到/etc目录下

 

安装gcc包：

rpm -ivh kernel-headers-2.6.18-274.el5.x86_64.rpm
rpm -ivh glibc-headers-2.5-65.x86_64.rpm
rpm -ivh glibc-devel-2.5-65.x86_64.rpm
rpm -ivh gcc-4.1.2-51.el5.x86_64.rpm
rpm -ivh kernel-uek-devel-2.6.32-200.13.1.el5uek.x86_64.rpm

 

安装HBA卡驱动：

tar -xvf brocade_driver_linux_rhel5_v3-0-0-0.tar(5.5.6.7)(oracle).gz

rpm -ivh kernel-uek-devel-2.6.32-200.13.1.el5uek.x86_64.rpm

安装HBA卡驱动 radhat linux

./brocade_install_rhel.sh

安装HBA卡驱动 Oraclelinux

./brocade_install.sh

启动多路径服务：

[root@yoon ~]# chkconfig multipathd on

[root@yoon ~]#service multipathd start