keithley-吉时利-C#-测试电流电压

前言：使用GPIB线对测试仪器的连接与控制。（NI，VISA, 488.5）

下载驱动： NI官网

一.测试电流

测试电流需要输入电压。
代码如下：

/// <summary>
        /// 测试电流
        /// </summary>
        public string inputUvOutPutIs(string testType, string Us_val)
        {
            try
            {
                // 判断是否为正，是否为负
                string judge = "";
                if (testType == "+")
                {
                    judge = "";
                }
                else if (testType == "-")
                {
                    judge = "-";
                }

                else
                {
                    judge = "";
                }
                #region >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>参数设置
                // 初始化参数
                string textToWrite1, textToWrite2, textToWrite3, textToWrite4, textToWrite5, textToWrite6, textToWrite7,
                    textToWrite8, textToWrite9, textToWrite10, textToWrite11, textToWrite12;
                // *****************吉时利
                textToWrite1 = Session.Instance.ReplaceCommonEscapeSequences("*RST");
                textToWrite2 = Session.Instance.ReplaceCommonEscapeSequences(":SOUR:FUNC VOLT"); // 输入源为电压
                textToWrite3 = Session.Instance.ReplaceCommonEscapeSequences(":SOUR:VOLT:MODE FIX");  // MODE
                //textToWrite4 = Session.Instance.ReplaceCommonEscapeSequences(":SOUR:CURR:RANG " + CurrentMaterialClass.is_min.ToString()
                //    + " " + CurrentMaterialClass.is_max.ToString()); // 选择输入量程
                textToWrite5 = Session.Instance.ReplaceCommonEscapeSequences(":SOUR:VOLT:LEV " + judge + Us_val); // Us输入大小
                textToWrite6 = Session.Instance.ReplaceCommonEscapeSequences(":SENS:FUNC 'CURR'"); // 测试项为 电压
                textToWrite7 = Session.Instance.ReplaceCommonEscapeSequences(":SENS:CURR:PROT " + CurrentMaterialClass.short_circuit.ToString() + "e-6"); // 保护电流，一般为最大值的1.5倍
                //textToWrite8 = Session.Instance.ReplaceCommonEscapeSequences(":SENS:VOLT:RANG 10e-3"); // 测试电压的量程
                //textToWrite9 = Session.Instance.ReplaceCommonEscapeSequences(":SENSe:CURR:NPLCycles " + Convert.ToInt32((Convert.ToInt32(CurrentMaterialClass.is_test_time) / 20)).ToString()); // nplc 0.1 1 2 12 通电速度
                textToWrite9 = Session.Instance.ReplaceCommonEscapeSequences(":SENSe:CURR:NPLCycles 1"); // nplc 0.1 1 2 12 通电速度
                textToWrite10 = Session.Instance.ReplaceCommonEscapeSequences(":OUTP ON"); // 输入源开启
                textToWrite11 = Session.Instance.ReplaceCommonEscapeSequences(":READ?"); // 返回数据
                textToWrite12 = Session.Instance.ReplaceCommonEscapeSequences(":OUTP OFF"); // 输入源开启
                #endregion
                if (StatusClass.seesionConnectIsSuccess)
                {
                    // 写入数据
                    Session.Instance.mbSession.RawIO.Write(textToWrite1);
                    Session.Instance.mbSession.RawIO.Write(textToWrite2);
                    Session.Instance.mbSession.RawIO.Write(textToWrite3);
                    //Session.Instance.mbSession.RawIO.Write(textToWrite4);
                    Session.Instance.mbSession.RawIO.Write(textToWrite5);
                    Session.Instance.mbSession.RawIO.Write(textToWrite6);
                    Session.Instance.mbSession.RawIO.Write(textToWrite7);
                    //Session.Instance.mbSession.RawIO.Write(textToWrite8);
                    Session.Instance.mbSession.RawIO.Write(textToWrite9);
                    Session.Instance.mbSession.RawIO.Write(textToWrite10);
                    // 延时测试
                    Thread.Sleep(Convert.ToInt32(CurrentMaterialClass.is_test_time));
                    Session.Instance.mbSession.RawIO.Write(textToWrite11);

                    // 获取输出数据
                    string rowStr = Session.Instance.InsertCommonEscapeSequences(Session.Instance.mbSession.RawIO.ReadString());
                    string[] resStrList = rowStr.Split(',');  // uA
                    string res_val = Math.Round(Session.Instance.ChangeDataToD(resStrList[1])*1000000, 3).ToString();
                    //b = rowStr.Replace("\\n", "");
                    //b = b.Substring(1, b.Length - 1); // 测量真实值字符串

                    // 关闭输入源
                    Session.Instance.mbSession.RawIO.Write(textToWrite12);

                    return res_val;
                }
                return "0";
            }
            catch (Exception ex)
            {
                MyDataSaveClass.Instance.SaveLogData("inputUvOutPutIs-ERROR:" + ex.Message);
                return "0";
                

            }
        }

二.测试电压

测试电压需要输入电流。

注意，吉时利仪器最大输入电压为1000V，不然会仪器报错。

代码如下：

/// <summary>
        /// 测试电压
        /// </summary>
        public string inputIsOutPutUv(string testType)
        {
            try
            {
                // 判断是否为正，是否为负
                string judge = "";
                if (testType == "+")
                {
                    judge = "";
                }
                else if (testType == "-")
                {
                    judge = "-";
                }
                else
                {
                    judge = "";
                }

                #region >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>参数设置
                // 初始化参数
                string textToWrite1, textToWrite2, textToWrite3, textToWrite4, textToWrite5, textToWrite6, textToWrite7,
                    textToWrite8, textToWrite9, textToWrite10, textToWrite11, textToWrite12;
                // *****************吉时利
                textToWrite1 = Session.Instance.ReplaceCommonEscapeSequences("*RST");
                textToWrite2 = Session.Instance.ReplaceCommonEscapeSequences(":SOUR:FUNC CURR"); // 输入源为电流
                textToWrite3 = Session.Instance.ReplaceCommonEscapeSequences(":SOUR:CURR:MODE FIX");  // MODE
                //textToWrite4 = Session.Instance.ReplaceCommonEscapeSequences(":SOUR:CURR:RANG " + CurrentMaterialClass.is_min.ToString()
                //    + " " + CurrentMaterialClass.is_max.ToString()); // 选择输入量程
                textToWrite5 = Session.Instance.ReplaceCommonEscapeSequences(":SOUR:CURR:LEV " + judge + (CurrentMaterialClass.is_input/1000).ToString()); // Iv输入大小
                textToWrite6 = Session.Instance.ReplaceCommonEscapeSequences(":SENS:FUNC 'VOLT'"); // 测试项为 电压
                textToWrite7 = Session.Instance.ReplaceCommonEscapeSequences(":SENS:VOLT:PROT " + CurrentMaterialClass.poor_contact.ToString()); // 保护电压 为接触不良电压，一般为最大值的1.5倍
                //textToWrite8 = Session.Instance.ReplaceCommonEscapeSequences(":SENS:VOLT:RANG 10e-3"); // 测试电压的量程
                textToWrite9 = Session.Instance.ReplaceCommonEscapeSequences(":SENSe:VOLT:NPLCycles 1"); // nplc 0.1 1 2 12 通电速度
                textToWrite10 = Session.Instance.ReplaceCommonEscapeSequences(":OUTP ON"); // 输入源开启
                textToWrite11 = Session.Instance.ReplaceCommonEscapeSequences(":READ?"); // 返回数据
                textToWrite12 = Session.Instance.ReplaceCommonEscapeSequences(":OUTP OFF"); // 输入源开启
                #endregion
                if (StatusClass.seesionConnectIsSuccess)
                {
                    // 写入数据
                    Session.Instance.mbSession.RawIO.Write(textToWrite1);
                    Session.Instance.mbSession.RawIO.Write(textToWrite2);
                    Session.Instance.mbSession.RawIO.Write(textToWrite3);
                    //Session.Instance.mbSession.RawIO.Write(textToWrite4);
                    Session.Instance.mbSession.RawIO.Write(textToWrite5);
                    Session.Instance.mbSession.RawIO.Write(textToWrite6);
                    Session.Instance.mbSession.RawIO.Write(textToWrite7);
                    //Session.Instance.mbSession.RawIO.Write(textToWrite8);
                    Session.Instance.mbSession.RawIO.Write(textToWrite9);
                    Session.Instance.mbSession.RawIO.Write(textToWrite10);
                    // 延时测试
                    Thread.Sleep(Convert.ToInt32( CurrentMaterialClass.uv_test_time));
                    Session.Instance.mbSession.RawIO.Write(textToWrite11);

                    // 获取输出数据
                    string rowStr = Session.Instance.InsertCommonEscapeSequences(Session.Instance.mbSession.RawIO.ReadString());
                    string[] resStrList = rowStr.Split(',');
                    string res_val =  Math.Round(Session.Instance.ChangeDataToD(resStrList[0]), 3).ToString();

                    // 关闭输入源
                    Session.Instance.mbSession.RawIO.Write(textToWrite12);

                    return res_val;


                }

               
                return "0";

            }
            catch (Exception ex)
            {

                MyDataSaveClass.Instance.SaveLogData("inputIsOutPutUv-ERROR:" + ex.Message);
                return "0";
            }
        }