【014】基于51单片机的16x16点阵滚动显示牌Proteus仿真

一、压缩包资料内容（私信）

• （1）、基于51单片机的16x16点阵滚动显示牌proteus仿真设计一份；
• （2）、基于51单片机的16x16点阵滚动显示牌proteus仿真设计keli源代码一份；
• （3）、基于51单片机的16x16点阵滚动显示牌proteus仿真设计报告一份；
• （4）、基于51单片机的16x16点阵滚动显示牌proteus仿真设计视频讲解一份；

二、设计要求

• （1）、本次电子实训课程要求以51系列单片机作为主控制芯片，设计一款16x16点阵滚动显示牌系统；
• （2）、系统要求采用数点阵模块构建广告牌；
• （3）、系统采用流动显示的方式显示指定内容；

三、相关资料截图

图1. 系统proteus仿真界面截图

图2. Keil编程界面源代码截图

图3. 系统设计报告截图 

图4.原理图

 

四、视频讲解

部分代码：

#include<reg51.h>
#include<intrins.h>
#define uchar unsigned char
#define uint unsigned int
#define data1 P0
#define data2 P2
sbit s1=P3^6;
sbit s2=P3^7;
bit fangxiang;
uint alt=0,net=0,sl=160;
bit mode;
uchar code tab[]={
//
//0x20,0x08,0x24,0x10,0x22,0x60,0x21,0x80,0x26,0x41,0x39,0x32,0x02,0x04,0x0C,0x18,
//0xF0,0x60,0x13,0x80,0x10,0x60,0x10,0x18,0x14,0x04,0x18,0x02,0x00,0x01,0x00,0x00,/*"欢",2*/

//0x02,0x00,0x02,0x02,0x42,0x04,0x33,0xF8,0x00,0x04,0x00,0x02,0x3F,0xF2,0x20,0x22,
//0x40,0x42,0x00,0x02,0x3F,0xFE,0x20,0x42,0x20,0x22,0x3F,0xC2,0x00,0x02,0x00,0x00,/*"迎",3*/

//0x00,0x80,0x01,0x00,0x06,0x00,0x1F,0xFF,0xE0,0x00,0x02,0x08,0x04,0x30,0x18,0xC0,
//0xF0,0x02,0x10,0x01,0x13,0xFE,0x10,0x00,0x10,0x80,0x14,0x60,0x18,0x18,0x00,0x00,/*"你",4*/

//0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*" ",5*/

//0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,/*" ",6*/
	

	
0x00,0x10,0x00,0x20,0x00,0xC0,0x07,0x00,0x00,0x00,0x00,0x02,0x00,0x01,0xFF,0xFE,
0x00,0x00,0x00,0x00,0x00,0x00,0x04,0x00,0x02,0x00,0x01,0x80,0x00,0x70,0x00,0x00,/*"小",0*/

0x00,0x04,0x48,0x08,0x44,0x10,0x42,0x60,0x41,0x80,0x46,0x60,0x78,0x18,0x00,0x00,
0x00,0x00,0x7F,0xFF,0x40,0x10,0x44,0x08,0x5B,0x10,0x60,0xE0,0x00,0x00,0x00,0x00,/*"邓",1*/

0x01,0x00,0x41,0x00,0x41,0x00,0x41,0x00,0x41,0x00,0x41,0x02,0x41,0x01,0x47,0xFE,
0x45,0x00,0x49,0x00,0x51,0x00,0x61,0x00,0x41,0x00,0x01,0x00,0x01,0x00,0x00,0x00,/*"子",2*/

0x01,0x00,0x02,0x01,0x04,0x02,0x09,0x04,0x11,0x18,0x61,0xE0,0x01,0x00,0x01,0x02,
0x01,0x01,0xC1,0x02,0x31,0xFC,0x08,0x00,0x04,0x00,0x02,0x00,0x01,0x00,0x00,0x00,/*"分",3*/

0x00,0x10,0x20,0x10,0x20,0x10,0x2E,0x90,0x2A,0x90,0x2A,0x92,0xAA,0x91,0x6A,0xBE,
0x2A,0xB0,0x2A,0xD0,0x2A,0x90,0x2E,0x10,0x20,0x10,0x20,0x10,0x00,0x10,0x00,0x00,/*"享",4*/

0x08,0x00,0x30,0x00,0x20,0x00,0x27,0xFF,0x24,0x92,0x24,0x92,0xA4,0x92,0x64,0x92,
0x24,0x92,0x24,0x92,0x24,0x92,0x27,0x92,0x20,0x1F,0x28,0x00,0x30,0x00,0x00,0x00,/*"官",5*/
	

};

void delay(uint z)	   //延时子函数
{
   uchar x;
   for(;z>0;z--)
   for(x=110;x>0;x--);
}

void xianshi()			//显示
{ 
	uchar aa,i;
	for(i=0;i<16;i++)
	{
		P1=i; //列扫描