DDR Version 1.04 20130517
In
DDR3
300MHz
Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Die Bus-Width=16 Size=1024MB
Memory OK
OUT
U-Boot 2014.01-g368bb5f (Feb 12 2015 - 17:14:19)
U-Boot code: 60200000 -> 602206D0 BSS: -> 60660F98
IRQ Stack: 0badc0de
FIQ Stack: 0badc0de
CPU: RKPX2
Board: RK30xx platform Board
monitor len: 00460F98
ramsize: 04000000
TLB table from 63ff0000 to 63ff4000
Top of RAM usable for U-Boot at: 63ff0000
Reserving 4000k for fb buffers at 63c08000
Reserving 4096k for rk global buffers at 63808000
Reserving 32768k for fastboot transfer buffer at 61808000
Reserving 2048k for fastboot log buffer at 61608000
Reserving 4483k for U-Boot at: 611a7000
Reserving 1025k for malloc() at: 610a6c00
Reserving 32 Bytes for Board Info at: 610a6be0
Reserving 184 Bytes for Global Data at: 610a6b28
Reserving 69632 Bytes for IRQ stack at: 61095b28
New Stack Pointer is: 61095b18
total reserving memory(except stack) is :48m
RAM Configuration:
Bank #0: 60000000 64 MiB
relocation Offset is: 00fa7000
monitor flash len: 00023F88
Now running in RAM - U-Boot at: 611a7000
arch_interrupt_init
DMAInit: OK
SdmmcInit=2 0
FwPartOffset=2000 , 0
storage init OK!
Using default environment
In: serial
Out: serial
Err: serial
board_late_init
unsigned!
SecureBootEn = 0 0
##################################################
uboot version: U-Boot 2014.01-g368bb5f (Feb 12 2015 - 17:14:19)
#Boot ver: 2015-02-12#0.02
##################################################
setup gpio int
GetParam
check parameter success
parameter base address is 0xbcfb
partition(uboot): offset=0x00002000, size=0x00002000
partition(misc): offset=0x00004000, size=0x00002000
partition(kernel): offset=0x00006000, size=0x00004000
partition(boot): offset=0x0000A000, size=0x00008000
partition(recovery): offset=0x00016000, size=0x00010000
partition(backup): offset=0x0002A000, size=0x00016000
partition(cache): offset=0x00040000, size=0x00040000
partition(userdata): offset=0x00080000, size=0x001FE000
partition(metadata): offset=0x0027E000, size=0x00002000
partition(kpanic): offset=0x00280000, size=0x00002000
partition(system): offset=0x00282000, size=0x00180000
partition(user): offset=0x00402000, size=0xFFFFFFFF
empty serial no.
checkKey
vbus = 1
lcd_ctrl_init [38]
i2c init OVER in board!
set_lcdc_dclk: lcdc_source_clk = 768, clk = 71, div = 11
rk30_load_screen for lcdc ok!
lcd_enable [55]
In charging!
SecureBootCheckOK:0
booti: do_bootm_linux...
Starting kernel ...
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.0.36+ (yxj@rk-mid) (gcc version 4.6.x-google 20120106 (prerelease) (GCC) ) #5 SMP PREEMPT Fri Mar 14 09:30:52 CST 2014
[ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d
[ 0.000000] CPU: VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: RKPX2board
[ 0.000000] Ignoring unrecognised tag 0x00000000
[ 0.000000] memory reserve: Memory(base:0x9b000000 size:80M) reserved for <ion>
[ 0.000000] memory reserve: Memory(base:0x9a500000 size:11M) reserved for <fb0 buf>
[ 0.000000] memory reserve: Memory(base:0x99900000 size:12M) reserved for <camera_ipp_mem>
[ 0.000000] memory reserve: Total reserved 103M
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] bootconsole [earlycon0] enabled
[ 0.000000] CPU SRAM: copied sram code from c0beb000 to fef00010 - fef01b90
[ 0.000000] CPU SRAM: copied sram data from c0becb80 to fef01b90 - fef022f0
[ 0.000000] sram_log: c m ^ 9= b d r <+ Z + ( E ve3
[ 0.000000] can't get a available nume and deno
[ 0.000000] clk_frac_div can't get rate=49500000,uart0_frac_div
[ 0.000000] rk30_dvfs_init
[ 0.000000] L310 cache controller enabled
[ 0.000000] l2x0: 16 ways, CACHE_ID 0x4100c0c8, AUX_CTRL 0x76050001, Cache size: 524288 B
[ 0.000000] DDR DEBUG: version 1.00 201300814
[ 0.000000] DDR DEBUG: DDR3 Device
[ 0.000000] DDR DEBUG: Bus Width=32 Col=10 Bank=8 Row=15 CS=1 Total Capability=1024MB
[ 0.000000] DDR DEBUG: init success!!! freq=396MHz
[ 0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=1 extra clock, DGPS=180
[ 0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=1 extra clock, DGPS=180
[ 0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=1 extra clock, DGPS=180
[ 0.000000] DDR DEBUG: DTONE=0x1, DTERR=0x0, DTIERR=0x0, DTPASS=0x4, DGSL=1 extra clock, DGPS=180
[ 0.000000] DDR DEBUG: ZERR=0, ZDONE=0, ZPD=0x0, ZPU=0x0, OPD=0x0, OPU=0x0
[ 0.000000] DDR DEBUG: DRV Pull-Up=0xb, DRV Pull-Dwn=0xb
[ 0.000000] DDR DEBUG: ODT Pull-Up=0x2, ODT Pull-Dwn=0x2
[ 0.000000] rk30_iomux_init
[ 0.000000] PERCPU: Embedded 7 pages/cpu @c1ea9000 s7424 r8192 d13056 u32768
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 233728
[ 0.000000] Kernel command line: console=ttyFIQ0 androidboot.console=ttyFIQ0 init=/init initrd=0x62000000,0x00150000 mtdparts=rk29xxnand:0x00002000@0x00002000(uboot),0x00002000@0x00004000(misc),0x00004000@0x00006000(kernel),0x00008000@0x0000a000(boot),0x00010000@0x00016000(recovery),0x00016000@0x0002a000(backup),0x00040000@0x00040000(cache),0x001FE000@0x00080000(userdata),0x00002000@0x0027E000(metadata),0x00002000@0x00280000(kpanic),0x00180000@0x00282000(system),-@0x00402000(user) androidboot.bootloader=fastboot fb.addr=0x63c08000 androidboot.serialno=0123456789
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] allocated 4194304 bytes of page_cgroup
[ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[ 0.000000] Memory: 921MB = 921MB total
[ 0.000000] Memory: 909900k/909900k available, 138676k reserved, 443392K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] DMA : 0xff600000 - 0xffe00000 ( 8 MB)
[ 0.000000] vmalloc : 0xdf000000 - 0xfe800000 ( 504 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xde800000 ( 488 MB)
[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
[ 0.000000] .init : 0xc0408000 - 0xc0436000 ( 184 kB)
[ 0.000000] .text : 0xc0436000 - 0xc0b78330 (7433 kB)
[ 0.000000] .data : 0xc0b7a000 - 0xc0bea548 ( 450 kB)
[ 0.000000] .bss : 0xc0bee024 - 0xc169f8c8 (10951 kB)
[ 0.000000] SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] NR_IRQS:448
[ 0.000000] rk30_gpio_init: 176 gpio irqs in 6 banks
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000033] Calibrating delay loop (skipped) preset value.. 1631.46 BogoMIPS (lpj=8157341)
[ 0.008832] pid_max: default: 32768 minimum: 301
[ 0.013892] Security Framework initialized
[ 0.018273] SELinux: Initializing.
[ 0.022118] Mount-cache hash table entries: 512
[ 0.027500] Initializing cgroup subsys debug
[ 0.032063] Initializing cgroup subsys cpuacct
[ 0.036872] Initializing cgroup subsys memory
[ 0.041564] Initializing cgroup subsys freezer
[ 0.046358] CPU: Testing write buffer coherency: ok
[ 0.051773] hw perfevents: enabled with ARMv7 Cortex-A9 PMU driver, 7 counters available
[ 0.152272] CPU1: Booted secondary processor
[ 0.152318] Brought up 2 CPUs
[ 0.160086] SMP: Total of 2 processors activated (3262.93 BogoMIPS).
[ 0.167182] devtmpfs: initialized
[ 0.178054] NET: Registered protocol family 16
[ 0.182904] last_log: 0xde100000 map to 0xdf004000 and copy to 0xc0bf22e8 (version 2.1)
[ 0.203263] DVFS MSG: AVS Value(index=0): 167 164 165 165 164 165 165 165 164 166
[ 0.222607] lcdc0 is used as primary display device contoller!
[ 0.229104] lcdc1 is used as external display device controller!
[ 0.336080] rk29sdk_wifi_bt_gpio_control_init: init finished
[ 0.342444] hw-breakpoint: found 6 breakpoint and 1 watchpoint registers.
[ 0.349993] hw-breakpoint: 1 breakpoint(s) reserved for watchpoint single-step.
[ 0.358140] hw-breakpoint: maximum watchpoint size is 4 bytes.
<hit enter to activate fiq debugger>
0.365955] console [ttyFIQ0] enabled, bootconsole disabled
[ 0.365955] console [ttyFIQ0] enabled, bootconsole disabled
[ 0.375027] Registered FIQ tty driver de098c00
[ 0.375624] Loaded driver for PL330 DMAC-1 rk29-pl330
[ 0.375661] DBUFF-32x8bytes Num_Chans-6 Num_Peri-12 Num_Events-12
[ 0.375826] Loaded driver for PL330 DMAC-2 rk29-pl330
[ 0.375861] DBUFF-64x8bytes Num_Chans-7 Num_Peri-20 Num_Events-14
[ 0.407696] bio: create slab <bio-0> at 0
[ 0.412101] SCSI subsystem initialized
[ 0.412300] usbcore: registered new interface driver usbfs
[ 0.412412] usbcore: registered new interface driver hub
[ 0.426670] usbcore: registered new device driver usb
[ 0.427054] rk30_i2c rk30_i2c.0: i2c-0: RK30 I2C adapter
[ 0.427240] rk30_i2c rk30_i2c.1: i2c-1: RK30 I2C adapter
[ 0.427464] rk30_i2c rk30_i2c.2: i2c-2: RK30 I2C adapter
[ 0.427592] rk30_i2c rk30_i2c.3: i2c-3: RK30 I2C adapter
[ 0.427775] rk30_i2c rk30_i2c.4: i2c-4: RK30 I2C adapter
[ 0.458247] rk30-adc rk30-adc: rk30 adc: driver initialized
[ 0.458538] timed_gpio_probe
[ 0.458637] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.459047] Bluetooth: Core ver 2.16
[ 0.459114] NET: Registered protocol family 31
[ 0.459145] Bluetooth: HCI device and connection manager initialized
[ 0.459188] Bluetooth: HCI socket layer initialized
[ 0.459220] Bluetooth: L2CAP socket layer initialized
[ 0.459268] Bluetooth: SCO socket layer initialized
[ 0.460334] rk fb probe ok!
[ 0.487651] tps65910_pre_init,line=38
[ 0.490244] TPS65910 Set default voltage.
[ 0.492313] tps65910_pre_init,line=248
[ 0.516232] cfg80211: Calling CRDA to update world regulatory domain
[ 0.516330] tps65910_post_init,line=256
[ 0.516358] tps65910_post_init:g_pmic_type=2
[ 0.532478] tps65910_post_init set vio vcc_io=3300000mV end
[ 0.533515] tps65910_post_init set vpll vdd11=2500000mV end
[ 0.534537] tps65910_post_init set vdig2 vdd11=1100000mV end
[ 0.535557] tps65910_post_init set vaux33 vcc_tp=3300000mV end
[ 0.537930] tps65910_post_init set vdd1 vdd_cpu=1200000mV end
[ 0.540301] tps65910_post_init set vdd2 vcc_ddr=1200000mV end
[ 0.541322] tps65910_post_init set vdig1 vcc18_cif=1800000mV end
[ 0.542346] tps65910_post_init set vaux1 vcc25_hdmi=2500000mV end
[ 0.543368] tps65910_post_init set vaux2 vcca33=3300000mV end
[ 0.544386] tps65910_post_init set vdac vccio_wl=2800000mV end
[ 0.545406] tps65910_post_init set vmmc vcc28_cif=2800000mV end
[ 0.545545] tps65910_post_init,line=343 END
[ 0.545575] tps65910_i2c_probe:irq=356,irq_base=384,gpio_base=384
[ 0.555200] tps65910-rtc tps65910-rtc: rtc core: registered tps65910 as rtc0
[ 0.557929] tps65910_rtc_probe:ok
[ 0.558005] Switching to clocksource timer1
[ 0.561772] Switched to NOHz mode on CPU #0
[ 0.562307] Switched to NOHz mode on CPU #1
[ 0.567464] lcdc0:reg_phy_base = 0x1010c000,reg_vir_base:0xdf0ac000
[ 0.567542] fb0:win1
[ 0.567547] fb1:win0
[ 0.567552] fb2:win2
[ 0.567634] rk30 lcdc0 clk enable...
[ 0.588677] fb0:phy:9a500000>>vir:e0000000>>len:0xb00000
[ 0.588932] rk_fb_register>>>>>fb0
[ 0.654154] rk_fb_register>>>>>fb1
[ 0.654338] rk_fb_register>>>>>fb2
[ 0.654366] rk30 lcdc0 clk enable...
[ 0.654452] lcdc0: dclk:74250000>>fps:60 rk30_load_screen for lcdc0 ok!
[ 0.654496] lcdc0 wakeup from standby!
[ 0.654523] lcdc0 win1 open,atv layer:1
[ 0.658310] rk30 lcdc0 probe ok!
[ 0.658373] lcdc1:reg_phy_base = 0x1010e000,reg_vir_base:0xdf0b8000
[ 0.658440] fb0:win1
[ 0.658445] fb1:win0
[ 0.658450] fb2:win2
[ 0.658520] rk30 lcdc1 clk enable...
[ 0.658554] fb3:phy:9a500000>>vir:e0000000>>len:0xb00000
[ 0.658754] rk_fb_register>>>>>fb3
[ 0.659018] rk_fb_register>>>>>fb4
[ 0.659211] rk_fb_register>>>>>fb5
[ 0.659238] rk30 lcdc1 probe ok!
[ 0.659353] pwm_regulator_probe:n_voltages=19
[ 0.659524] pwm_regulator.0: driver initialized
[ 0.670698] NET: Registered protocol family 2
[ 0.670843] IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.671162] TCP established hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.672140] TCP bind hash table entries: 65536 (order: 7, 786432 bytes)
[ 0.673234] TCP: Hash tables configured (established 65536 bind 65536)
[ 0.673276] TCP reno registered
[ 0.673305] UDP hash table entries: 256 (order: 1, 8192 bytes)
[ 0.673356] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
[ 0.673665] NET: Registered protocol family 1
[ 0.673850] RK29 Backlight Driver Initialized.
[ 0.674103] Unpacking initramfs...
[ 0.741929] Freeing initrd memory: 1344K
[ 0.742117] rk30-tsadc rk30-tsadc: initialized
[ 0.742221] PMU: registered new PMU device of type 0
[ 0.743115] DVFS WARNING: vd_cpu : selector=86,but volt <=0
[ 0.743884] VPU_SERVICE: failed on clk_get aclk_ddr_vepu
[ 0.743929] VPU_SERVICE: failed on clk_get hclk_cpu_vcodec
[ 0.743965] vpu: power on
[ 0.744024] VPU_SERVICE: checking hw id 4831
[ 0.744483] vpu: power off...done
[ 0.744533] VPU_SERVICE: init success
[ 0.744816] audit: initializing netlink socket (disabled)
[ 0.744876] type=2000 audit(0.730:1): initialized
[ 0.745569] highmem bounce pool size: 64 pages
[ 0.745730] ashmem: initialized
[ 0.750677] fuse init (API version 7.16)
[ 0.752589] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.752640] io scheduler noop registered
[ 0.752668] io scheduler deadline registered
[ 0.752745] io scheduler cfq registered (default)
[ 0.759022] rga: Driver loaded succesfully
[ 0.760114] i2c i2c-2: No ack, Maybe slave(addr: 0x50) not exist or abnormal power-on, retry 2...
[ 0.761058] i2c i2c-2: No ack, Maybe slave(addr: 0x50) not exist or abnormal power-on, retry 1...
[ 0.761999] i2c i2c-2: No ack, Maybe slave(addr: 0x50) not exist or abnormal power-on, retry 0...
[ 0.762058] vga_i2c 2-0050: unable to read EDID block.
[ 0.762096] switch lcd device
[ 0.762117] VGA probe successful
[ 0.762320] rk_serial.c v1.6 2013-12-23
[ 0.762423] rk_serial.0: ttyS0 at MMIO 0x10124000 (irq = 66) is a rk29_serial.0
[ 0.762610] rk_serial rk_serial.0: membase 0xdf0c8000
[ 0.762915] Rockchip ion module(version: 1.0) is successfully loaded
[ 0.765537] loop: module loaded
[ 0.765594] Android kernel panic handler initialized (bind=kpanic)
[ 0.766402] random_ether_addr***********:6A:62:50:52:98:FC
[ 0.766754] rk29 vmac rk29 vmac.0: ARC VMAC at 0x10204000 irq 51 6a:62:50:52:98:fc
[ 0.766886] PPP generic driver version 2.4.2
[ 0.767062] PPP Deflate Compression module registered
[ 0.767097] PPP BSD Compression module registered
[ 0.767753] PPP MPPE Compression module registered
[ 0.767790] NET: Registered protocol family 24
[ 0.767822] tun: Universal TUN/TAP device driver, 1.6
[ 0.767855] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.768119] usbcore: registered new interface driver asix
[ 0.768193] usbcore: registered new interface driver cdc_ether
[ 0.768262] usbcore: registered new interface driver dm9620
[ 0.768330] usbcore: registered new interface driver SR9700_android
[ 0.768425] usbcore: registered new interface driver CoreChips
[ 0.768497] usbcore: registered new interface driver net1080
[ 0.768567] usbcore: registered new interface driver cdc_subset
[ 0.768634] usbcore: registered new interface driver zaurus
[ 0.768680] cdc_ncm: 04-Aug-2011
[ 0.768737] usbcore: registered new interface driver cdc_ncm
[ 0.768774] Rockchip WiFi SYS interface (V1.00) ...
[ 0.768837] Initializing USB Mass Storage driver...
[ 0.768912] usbcore: registered new interface driver usb-storage
[ 0.768951] USB Mass Storage support registered.
[ 0.769087] usbcore: registered new interface driver usbserial
[ 0.769155] USB Serial support registered for generic
[ 0.769228] usbcore: registered new interface driver usbserial_generic
[ 0.769270] usbserial: USB Serial Driver core
[ 0.769325] USB Serial support registered for GSM modem (1-port)
[ 0.769402] usbcore: registered new interface driver option
[ 0.769440] option: v0.7.2:USB Driver for GSM modems
[ 0.981898] DWC_OTG: ^^^^^^^^^^^^^^^^^Device Mode
[ 0.981933] usb20_otg usb20_otg: DWC OTG Controller
[ 0.982024] usb20_otg usb20_otg: new USB bus registered, assigned bus number 1
[ 0.982087] usb20_otg usb20_otg: irq 48, io mem 0x00000000
[ 0.982117] DWC_OTG: dwc_otg_hcd_start controller in device mode,everest
[ 0.982183] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.982220] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.982256] usb usb1: Product: DWC OTG Controller
[ 0.982281] usb usb1: Manufacturer: Linux 3.0.36+ dwc_otg_hcd
[ 0.982310] usb usb1: SerialNumber: usb20_otg
[ 0.982591] hub 1-0:1.0: USB hub found
[ 0.982619] hub 1-0:1.0: 1 port detected
[ 0.985163] DWC_OTG: host20_driver_probe host2.0 reg addr: 0x101c0000 remap:0xdf180000
[ 1.195437] DWC_OTG: ^^^^^^^^^^^^^^^^^^Host Mode
[ 1.195478] usb20_host usb20_host: DWC OTG Controller
[ 1.195529] usb20_host usb20_host: new USB bus registered, assigned bus number 2
[ 1.195581] usb20_host usb20_host: irq 49, io mem 0x00000000
[ 1.195641] DWC_OTG: Init: Port Power? op_state=1
[ 1.195667] DWC_OTG: Init: Power Port (0)
[ 1.195713] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 1.195749] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.195785] usb usb2: Product: DWC OTG Controller
[ 1.195809] usb usb2: Manufacturer: Linux 3.0.36+ host20_hcd
[ 1.195838] usb usb2: SerialNumber: usb20_host
[ 1.196099] hub 2-0:1.0: USB hub found
[ 1.196125] hub 2-0:1.0: 1 port detected
[ 1.197207] android_usb gadget: Mass Storage Function, version: 2009/09/11
[ 1.197245] android_usb gadget: Number of LUNs=2
[ 1.197271] lun0: LUN: removable file: (no medium)
[ 1.197297] lun1: LUN: removable file: (no medium)
[ 1.197456] android_usb gadget: android_usb ready
[ 1.197620] input: rk29-keypad as /devices/platform/rk29-keypad/input/input0
[ 1.197823] usbcore: registered new interface driver xpad
[ 1.197880] usbcore: registered new interface driver usb_acecad
[ 1.197909] acecad: v3.2:USB Acecad Flair tablet driver
[ 1.197958] usbcore: registered new interface driver aiptek
[ 1.197986] aiptek: v2.3 (May 2, 2007):Aiptek HyperPen USB Tablet Driver (Linux 2.6.x)
[ 1.198024] aiptek: Bryan W. Headley/Chris Atenasio/Cedric Brun/Rene van Paassen
[ 1.198110] usbcore: registered new interface driver gtco
[ 1.198138] GTCO usb driver version: 2.00.0006
[ 1.198182] usbcore: registered new interface driver hanwang
[ 1.198233] usbcore: registered new interface driver kbtab
[ 1.198260] kbtab: v0.0.2:USB KB Gear JamStudio Tablet driver
[ 1.198312] usbcore: registered new interface driver wacom
[ 1.198340] wacom: v1.52:USB Wacom tablet driver
[ 1.198478] sensor_register_slave:mma8452,id=17
[ 1.198506] sensor_register_slave:akm8963,id=23
[ 1.198530] sensor_register_slave:l3g4200d,id=37
[ 1.198658] remotectl probe j=0x0
[ 1.198678] remotectl probe j=0x1
[ 1.198782] input: rkxx-remotectl as /devices/platform/rkxx-remotectl/input/input1
[ 1.199050] using rtc device, tps65910, for alarms
[ 1.199246] lirc_dev: IR Remote Control driver registered, major 250
[ 1.199280] IR NEC protocol handler initialized
[ 1.199303] IR RC5(x) protocol handler initialized
[ 1.199327] IR RC6 protocol handler initialized
[ 1.199350] IR JVC protocol handler initialized
[ 1.199373] IR Sony protocol handler initialized
[ 1.199396] IR RC5 (streamzap) protocol handler initialized
[ 1.199424] IR LIRC bridge handler initialized
[ 1.199446] Linux video capture interface: v2.00
[ 1.199484]
[ 1.199486] adv7180_init..adv7180..
[ 1.199632] def_ref_volt: 2500mV, curr_ref_volt: 2500mV
[ 1.200042] device-mapper: uevent: version 1.0.3
[ 1.200251] device-mapper: ioctl: 4.20.0-ioctl (2011-02-02) initialised: dm-devel@redhat.com
[ 1.200426] Bluetooth: HCI UART driver ver 2.2
[ 1.200453] Bluetooth: HCI H4 protocol initialized
[ 1.200477] Bluetooth: HCILL protocol initialized
[ 1.200531] cpuidle: using governor ladder
[ 1.200554] cpuidle: using governor menu
[ 1.246002]
[ 1.246005] drivers/mmc/core/core.c...2015.. ===== mmc_rescan Begin....[mmc0]
[ 1.246049]
[ 1.246051] =================
[ 1.246055] sdmmc_rescan..2022.. ====find no SDMMC host. [mmc0]
[ 1.246117] .Line3985..The End of SDMMC-probe Ver.6.07 The last modify date is 2013-12-20. [sd_mmc]
[ 1.246281]
[ 1.246284] drivers/mmc/core/core.c...2015.. ===== mmc_rescan Begin....[mmc1]
[ 1.246334] .Line3985..The End of SDMMC-probe Ver.6.07 The last modify date is 2013-12-20. [sdio]
[ 1.247488] usbcore: registered new interface driver usbhid
[ 1.247518] usbhid: USB HID core driver
[ 1.247798] logger: created 256K log 'log_main'
[ 1.247882] logger: created 256K log 'log_events'
[ 1.247958] logger: created 256K log 'log_radio'
[ 1.248032] logger: created 256K log 'log_system'
[ 1.248141] ipp irq 47
[ 1.248257] IPP init, version rkpx2-ipp 1.003
[ 1.248528] zram: Created 1 device(s) ...
[ 1.258099] rk29_sdmmc_change_clk_div..1702.. newDiv=42, newCLK=297Khz [sdio]
[ 1.262608] asoc: WM8960 HiFi <-> rk29_i2s.0 mapping ok
[ 1.262898] ALSA device list:
[ 1.262916] #0: RK29_WM8960
[ 1.263007] GACT probability NOT on
[ 1.263031] Mirror/redirect action on
[ 1.263051] u32 classifier
[ 1.263065] Actions configured
[ 1.263085] Netfilter messages via NETLINK v0.30.
[ 1.263141] nf_conntrack version 0.5.0 (14238 buckets, 56952 max)
[ 1.263412] ctnetlink v0.93: registering with nfnetlink.
[ 1.263468] NF_TPROXY: Transparent proxy support initialized, version 4.1.0
[ 1.263504] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd.
[ 1.263752] xt_time: kernel timezone is -0000
[ 1.263890] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.264023] arp_tables: (C) 2002 David S. Miller
[ 1.264078] TCP cubic registered
[ 1.264096] Initializing XFRM netlink socket
[ 1.264436] NET: Registered protocol family 10
[ 1.264995] Mobile IPv6
[ 1.265029] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 1.265141] IPv6 over IPv4 tunneling driver
[ 1.265659] NET: Registered protocol family 17
[ 1.265700] NET: Registered protocol family 15
[ 1.265894] Bluetooth: RFCOMM TTY layer initialized
[ 1.265927] Bluetooth: RFCOMM socket layer initialized
[ 1.265954] Bluetooth: RFCOMM ver 1.11
[ 1.265975] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 1.266003] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 1.266111] NET: Registered protocol family 35
[ 1.266252] [BT_RFKILL]: Enter rfkill_rk_init
[ 1.266354] [BT_RFKILL]: Request irq for bt wakeup host
[ 1.266397] [BT_RFKILL]: ** disable irq
[ 1.288141] [BT_RFKILL]: bt shut off power
[ 1.318064] [BT_RFKILL]: ap6330 device registered.
[ 1.318437] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 1.318492] Registering SWP/SWPB emulation handler
[ 1.319047] input: rk_headsetdet as /devices/platform/rk_headsetdet.0/input/input2
[ 1.319208] =======================================================
[ 1.319240] ==== Launching Wi-Fi driver! (Powered by Rockchip) ====
[ 1.319270] =======================================================
[ 1.319302] WiFi driver (Powered by Rockchip,Ver 4.72.WFD.OOB) init.
[ 1.319566] =========== WLAN placed in POWER ON ========
[ 1.319611] ANDROID-ERROR) wifi_set_power = 1
[ 1.319637] rk29sdk_wifi_power: 1
[ 1.570032] wifi turn on power
[ 1.778074] ANDROID-ERROR) wifi_set_carddetect = 1
[ 1.778104] rk29sdk_wifi_set_carddetect:1
[ 1.778127] mmc1: slot status change detected(0-1)
[ 1.778231] rk_cam_cif(3282):rk30-camera version: v0.3.21 Zoom by ippret: 0
[ 1.820345] ret: 0
[ 1.858342] adv7180_probe 696
[ 1.858362] adv7180_probe 701
[ 1.858387] adv7180 3-0021: chip found @ 0x42 (rk30_i2c)
[ 1.858412] adv7180_probe 705
[ 1.858428] adv7180_probe 711
[ 1.858446] request ADV7180_CVBS_IN_DET pin fail!
[ 1.858474] adv7180: probe of 3-0021 failed with error -1
[ 1.870248] ret: 0
[ 1.898136] camera 33-0-adv7180_back_3: Probe adv7180_back_3 failed
[ 1.978086]
[ 1.978089] drivers/mmc/core/core.c...2015.. ===== mmc_rescan Begin....[mmc1]
[ 2.022140]
[ 2.022152] mmc_attach_sdio..1112.. ===== Begin to identify card as SDIO-card. [mmc1]
[ 2.101250] rk29_sdmmc_change_clk_div..1702.. newDiv=0, newCLK=25000Khz [sdio]
[ 2.107078] mmc1: new high speed SDIO card at address 0001
[ 2.108015] bcmsdh_register: Linux Kernel SDIO/MMC Driver
[ 2.108411]
[ 2.108423] Dongle Host Driver, version 1.88.45.1 (r420671)
[ 2.108448] Compiled in drivers/net/wireless/bcmdhd on Mar 7 2014 at 15:56:37
[ 2.109851] FW_PATH = /system/etc/firmware/fw_RK903_ag.bin
[ 2.109880] NVRAM_PATH = /system/etc/firmware/nvram_AP6330.txt
[ 2.122015] F1 signature OK, socitype:0x1 chip:0x4330 rev:0x4 pkg:0x0
[ 2.123100] DHD: dongle ram size is set to 294912(orig 294912) at 0x0
[ 2.138228] wl_create_event_handler(): thread:wl_event_handler:40 started
[ 2.139767] p2p0: P2P Interface Registered
[ 2.139866] tsk Enter, tsk = 0xdd2e1398
[ 2.139924] dhd_attach(): thread:dhd_watchdog_thread:41 started
[ 2.140029] dhd_attach(): thread:dhd_dpc:42 started
[ 2.140143] dhd_attach(): thread:dhd_sysioc:43 started
[ 2.140327] ANDROID-ERROR) wifi_get_mac_addr
[ 2.140842] Broadcom Dongle Host Driver: register interface [wlan0] MAC: 00:90:4c:11:22:33
[ 2.140915] sdmmc_rescan_try_freq..1863.. ===== Initialize SDIO successfully. [mmc1]
[ 2.141030] ANDROID-ERROR) wifi_set_power = 0
[ 2.141065] rk29sdk_wifi_power: 0
[ 2.342008] wifi shut off power
[ 2.342028] =========== WLAN placed in RESET ========
[ 2.342088] i2c i2c-0: sensor_probe: gs_mma8452,0xde1b4a00
[ 2.342362] sensor_chip_init:gs_mma8452:devid=0x2a,ops=0xc0bcf3cc
[ 2.343916] input: gsensor as /devices/platform/rk30_i2c.0/i2c-0/0-001d/input/input3
[ 2.358340] sensor_irq_init:use irq=304
[ 2.358454] sensor_misc_device_register:miscdevice: mma8452_daemon
[ 2.358486] sensor_probe:initialized ok,sensor name:mma8452,type:2,id=17
[ 2.358493]
[ 2.358538] i2c i2c-0: sensor_probe: ak8963,0xde1b4c00
[ 2.358800] sensor_chip_init:ak8963:devid=0x48,ops=0xc0bcf428
[ 2.359401] input: compass as /devices/platform/rk30_i2c.0/i2c-0/0-000d/input/input4
[ 2.359569] sensor_irq_init:use irq=305
[ 2.359662] sensor_misc_device_register:miscdevice: compass
[ 2.359693] sensor_probe:initialized ok,sensor name:akm8963,type:3,id=23
[ 2.359701]
[ 2.359747] i2c i2c-0: sensor_probe: l3g4200d_gryo,0xde1b4e00
[ 2.360014] i2c i2c-0: No ack, Maybe slave(addr: 0x69) not exist or abnormal power-on, retry 2...
[ 2.360280] i2c i2c-0: No ack, Maybe slave(addr: 0x69) not exist or abnormal power-on, retry 1...
[ 2.360543] i2c i2c-0: No ack, Maybe slave(addr: 0x69) not exist or abnormal power-on, retry 0...
[ 2.360807] i2c i2c-0: No ack, Maybe slave(addr: 0x69) not exist or abnormal power-on, retry 2...
[ 2.361070] i2c i2c-0: No ack, Maybe slave(addr: 0x69) not exist or abnormal power-on, retry 1...
[ 2.361334] i2c i2c-0: No ack, Maybe slave(addr: 0x69) not exist or abnormal power-on, retry 0...
[ 2.361598] i2c i2c-0: No ack, Maybe slave(addr: 0x69) not exist or abnormal power-on, retry 2...
[ 2.361860] i2c i2c-0: No ack, Maybe slave(addr: 0x69) not exist or abnormal power-on, retry 1...
[ 2.362123] i2c i2c-0: No ack, Maybe slave(addr: 0x69) not exist or abnormal power-on, retry 0...
[ 2.362167] sensor_chip_init:fail to read l3g4200d_gryo devid:0xff
[ 2.362199] i2c i2c-0: sensor_probe failed -11
[ 2.362204]
[ 2.362235] sensors: probe of 0-0069 failed with error -11
[ 2.362291] sensor_init: Probe name sensors
[ 2.362327] sensor-dev.c v1.4 add angle calculation support between two gsensors 2013-09-01
[ 2.365442] tps65910-rtc tps65910-rtc: setting system clock to 2000-01-01 07:36:27 UTC (946712187)
[ 2.367897] asoc: rk-hdmi-i2s-hifi <-> rk29_i2s.0 mapping ok
[ 2.368151] rk_hdmi_spdif:Entered rk_spdif_init
[ 2.370473] asoc: dit-hifi <-> rk-spdif.0 mapping ok
[ 2.370679] rk_hdmi_spdif:rk_spdif_init ok
[ 2.370733] ct360_ts_init
[ 2.370837] ct360_hw_init
[ 2.673616] i2c i2c-2: No ack, Maybe slave(addr: 0x1) not exist or abnormal power-on, retry 2...
[ 2.674065] i2c i2c-2: No ack, Maybe slave(addr: 0x1) not exist or abnormal power-on, retry 1...
[ 2.674510] i2c i2c-2: No ack, Maybe slave(addr: 0x1) not exist or abnormal power-on, retry 0...
[ 2.674555] ct360_write_regs:i2c_transfer fail =-11
[ 2.674580]
[ 2.674582] --ct360_ts_probe--Set Register values error !!!
[ 2.674624] ct360_ts: probe of 2-0001 failed with error -11
[ 2.674779] Freeing init memory: 184K
[ 2.928105] headset->isMic = 1
[ 2.983856] type=1403 audit(946712188.110:2): policy loaded auid=4294967295 ses=4294967295
[ 2.984399] SELinux: Loaded policy from /sepolicy
[ 2.992568] type=1404 audit(946712188.120:3): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
[ 4.175117] init (1): /proc/1/oom_adj is deprecated, please use /proc/1/oom_score_adj instead.
[ 4.227829] init: /dev/hw_random not found
[ 4.227923] keychord: using input dev rk29-keypad for fevent
[ 4.227956] keychord: using input dev rkxx-remotectl for fevent
[ 4.323481] gp_rknand_info = : 0xdd830600
[ 4.323585] rk30_chip_set:0
[ 4.323651] FtlInit!
[ 4.323676] gBootMedia = 2 gSdmmcFwPartOffset =2000!
[ 4.323706] CardId = 2
[ 4.459659] rk29_dma_set_buffdone_fn
[ 4.459684] EmmcBus_khz = 50000
[ 4.459714] SDM_Init OK
[ 4.460731] SDC_SetHostBusWidth flag 1 , 2 bits
[ 4.460771] EmmcBus_khz = 3947 , need = 4000
[ 4.537920] EmmcBus_khz = 25000 , need = 36000
[ 4.538408] EmmcBus_khz = 75000 , need = 100000
[ 4.538434] SDC_SetHostBusWidth flag 3 , 8 bits
[ 4.538492] SdmmcInit BootCapSize: 0x400
[ 4.538865] SdmmcInit UserCapSize: 0xe90000
[ 4.538888] SdmmcInit ret = 0!
[ 4.538906] rknand_buffer.c version: 4.40 20130830!
[ 4.539046] 12 cmdlinepart partitions found on MTD device rk29xxnand
[ 4.539081] Creating 12 MTD partitions on "rk29xxnand":
[ 4.539112] 0x000000400000-0x000000800000 : "uboot"
[ 4.540444] 0x000000800000-0x000000c00000 : "misc"
[ 4.541172] 0x000000c00000-0x000001400000 : "kernel"
[ 4.541653] 0x000001400000-0x000002400000 : "boot"
[ 4.542121] 0x000002c00000-0x000004c00000 : "recovery"
[ 4.542600] 0x000005400000-0x000008000000 : "backup"
[ 4.543083] 0x000008000000-0x000010000000 : "cache"
[ 4.543615] 0x000010000000-0x00004fc00000 : "userdata"
[ 4.544706] 0x00004fc00000-0x000050000000 : "metadata"
[ 4.545152] 0x000050000000-0x000050400000 : "kpanic"
[ 4.546367] apanic: Bound to mtd partition 'kpanic'
[ 4.546394] apanic: No panic data available
[ 4.546424] 0x000050400000-0x000080400000 : "system"
[ 4.547354] 0x000080400000-0x0001d1c00000 : "user"
[ 4.563433] fs_mgr: parse_link_device : in
[ 4.563481] fs_mgr: parse_link_device : ---- part_num = 11, path = /devices/virtual/mtd/mtd11/mtdblock11, is_emmc = 0
[ 4.563557] fs_mgr: parse_link_device : path = NULL
[ 4.563601] fs_mgr: parse_link_device : path = NULL
[ 4.563673] fs_mgr: ---------------resize_fs blk_dev /dev/block/mtd/by-name/system, type ext4
[ 4.563720] fs_mgr: Running /sbin/resize2fs on /dev/block/mtd/by-name/system
[ 4.570097] resize2fs: resize2fs 1.41.14 (22-Dec-2010)
[ 4.575469] resize2fs: The filesystem is already 196608 blocks long. Nothing to do!
[ 4.575541] resize2fs:
[ 4.601702] EXT4-fs (mtdblock10): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard
[ 4.616030] EXT4-fs (mtdblock6): recovery complete
[ 4.616172] EXT4-fs (mtdblock6): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard
[ 4.618236] EXT4-fs (mtdblock8): warning: mounting unchecked fs, running e2fsck is recommended
[ 4.618442] EXT4-fs (mtdblock8): mounted filesystem without journal. Opts: noauto_da_alloc,discard
[ 4.821350] EXT4-fs (mtdblock7): recovery complete
[ 4.821520] EXT4-fs (mtdblock7): mounted filesystem with ordered data mode. Opts: noauto_da_alloc,discard
[ 4.846531] UMP: UMP device driver -v3.0.66-13396-ga93bf73 loaded
[ 4.879384] Mali: init_mali_clock --------------------------
[ 4.879590] Mali: init mali clock success ywj
[ 4.881121] Mali: Mali device driver loaded
[ 4.883967] rk30_mirroring: Unknown symbol video_data_to_mirroring (err 0)
[ 4.884041] rk30_mirroring: Unknown symbol audio_data_to_mirroring (err 0)
[ 4.897621] init: /dev/hw_random not found
[ 4.915280] init: cannot find '/system/vendor/bin/pvrsrvctl', disabling 'pvrsrvctl'
[ 4.918221] healthd: BatteryVoltagePath not found
[ 4.918256] healthd: BatteryTemperaturePath not found
[ 4.918310] binder: 94:94 transaction failed 29189, size 0-0
[ 4.924232] init: cannot find '/system/bin/rild3', disabling 'ril-daemon3'
[ 5.049175] init: cannot find '/system/etc/install-recovery.sh', disabling 'flash_recovery'
[ 5.064939] init: property 'ro.serialno' doesn't exist while expanding '${ro.serialno}'
[ 5.065049] init: cannot expand '${ro.serialno}' while writing to '/sys/class/android_usb/android0/iSerial'
[ 5.065639] init: using deprecated syntax for specifying property 'ro.product.usbfactory', use ${name} instead
[ 5.128343] init: property 'sys.powerctl' doesn't exist while expanding '${sys.powerctl}'
[ 5.128413] init: powerctl: cannot expand '${sys.powerctl}'
[ 5.128471] init: property 'sys.sysctl.extra_free_kbytes' doesn't exist while expanding '${sys.sysctl.extra_free_kbytes}'
[ 5.128542] init: cannot expand '${sys.sysctl.extra_free_kbytes}' while writing to '/proc/sys/vm/extra_free_kbytes'
[ 5.130931] android_usb: already disabled
[ 5.154792] RKNAND_GET_DRM_KEY
[ 5.154820] return ret = 0
[ 5.163195] adb_open
shell@rkpx2:/ $ [ 5.343278] fs_mgr: parse_link_device : in
[ 5.347741] fs_mgr: parse_link_device : ---- part_num = 11, path = /devices/virtual/mtd/mtd11/mtdblock11, is_emmc = 0
[ 5.347877] fs_mgr: parse_link_device : path = NULL
[ 5.347940] fs_mgr: parse_link_device : path = NULL
[ 5.348302] .200.. MMC0 receive the message sd-No-Media from VOLD.[sd_mmc]
[ 5.348351] .231.. MMC0 receive the message No-Media from VOLD. waitTimes=0 [sd_mmc]
[ 5.636685] rk fb use 3 buffers
[ 9.218171] DWC_OTG: dwc_otg_hcd_enable, disable host controller
[ 17.008108] DWC_OTG: ********vbus detect*********************************************
[ 17.232877] DWC_OTG: ********soft connect!!!*****************************************
[ 17.238879] DWC_OTG: USB SUSPEND
[ 17.243065] warning: `zygote' uses 32-bit capabilities (legacy support in use)
[ 17.357380] DWC_OTG: USB RESET
[ 17.485404] android_work: sent uevent USB_STATE=CONNECTED
[ 17.486653] android_usb gadget: high speed config #1: android
[ 17.487005] android_work: sent uevent USB_STATE=CONFIGURED
[ 21.292619] healthd: battery l=50 v=0 t=0.0 h=2 st=3 chg=a
[ 21.300545] request_suspend_state: wakeup (3->0) at 21292484213 (2000-01-01 07:36:46.432353585 UTC)
[ 21.672215] enter func vmac_open...
[ 21.778194] power on phy
[ 22.800730] vmac_mii_bus: probed
[ 22.801636] rk29 vmac rk29 vmac.0: PHY driver [Generic PHY] (mii_bus:phy_addr=0:00, irq=-1)
[ 22.805345] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 23.042677] acc_open
[ 23.042711] acc_release
[ 23.724083] init: no such service 'fuse_internal_sd'
[ 24.798549] PHY: 0:00 - Link is Down
[ 26.635044] vpu: power on
[ 27.370389] init: sys_prop: permission denied uid:1003 name:service.bootanim.exit
[ 30.638123] vpu: power off...done
04-08
2724
2724
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
