Arduino文档阅读笔记-WeMos D1 ESP8266 WIFI开发板入门

WeMos D1开发板以ESP8266WIFI开发板为基础，使用Arduino开发板的设计，工作电压为3.3V设计出来的开发板，这个开发板仅仅是使用了Arduino uno的布局设计，并不是Arduino的开发板。

下面是关于这块开发板的说明书：

总结下：

此开发板芯片为ESP8266（32位），缓存比Arduino Uno大，并且包含11个数字IO引脚以及1个模拟输入引脚，使用Micro-B type USB线进行连接。

下面是引脚方面的说明！

所有的引脚都需要跑到3.3V上，并且除了D0口其他口都支持interrupt/PWM/I2C/one-wire。

下面是在Arduino IDE中部署其开发环境

软件需要如下3个：

CH340G USB to UART driver: https://www.wemos.cc/downloads

Python 2.7: https://www.python.org/downloads/release/python-2713/

Arduino 1.8.2: https://www.arduino.cc/en/Main/Software

在Github上下载其库文件：

将压缩包放到esp8266目录下，然后解压：

将里面的文件移到到esp8266中，再将Arduino-master与Arduino-master.zip删掉。

最后变成这个样子即可！

打开CMD然后执行如下命名：

python get.py

此命令将会下载开发板所需要的工具，一切正常，且安装好将会是这样的。

这样就完成了安装！！！
使用Arduino IDE时要选中正确的开发板，Toos>Board中选择"WeMos D1 R2 & Mini"即可：

下面是几个示例代码：

/*
 ESP8266 Blink by Simon Peter
 Blink the blue LED on the ESP-01 module
 This example code is in the public domain
 
 The blue LED on the ESP-01 module is connected to GPIO1 
 (which is also the TXD pin; so we cannot use Serial.print() at the same time)
 
 Note that this sketch uses LED_BUILTIN to find the pin with the internal LED
*/
 
void setup() {
  pinMode(LED_BUILTIN, OUTPUT);     // Initialize the LED_BUILTIN pin as an output
}
 
// the loop function runs over and over again forever
void loop() {
  digitalWrite(LED_BUILTIN, LOW);   // Turn the LED on (Note that LOW is the voltage level
                                    // but actually the LED is on; this is because 
                                    // it is active low on the ESP-01)
  delay(1000);                      // Wait for a second
  digitalWrite(LED_BUILTIN, HIGH);  // Turn the LED off by making the voltage HIGH
  delay(2000);                      // Wait for two seconds (to demonstrate the active low LED)
}

查看下芯片的ID，这里串口打印频率要选择115200

/*  Get Chip ID
 *  wemos.cc
 *  
 *  
 */
 
void setup() {
  Serial.begin(115200);
}
 
void loop() {
  Serial.println("");
  Serial.println("");
  Serial.println("Check ID in:");
  Serial.println("https://www.wemos.cc/verify_products");
  Serial.printf("Chip ID = %08Xn", ESP.getChipId());
  Serial.println("");
  Serial.println("");
  delay(5000);
}

运行一个简单的Web Server

#include <ESP8266WiFi.h>
#include <WiFiClient.h>
#include <ESP8266WebServer.h>
#include <ESP8266mDNS.h>
 
const char* ssid = "........";
const char* password = "........";
 
ESP8266WebServer server(80);
 
const int led = 13;
 
void handleRoot() {
  digitalWrite(led, 1);
  server.send(200, "text/plain", "Hello from esp8266!");
  digitalWrite(led, 0);
}
 
void handleNotFound(){
  digitalWrite(led, 1);
  String message = "File Not Foundnn";
  message += "URI: ";
  message += server.uri();
  message += "nMethod: ";
  message += (server.method() == HTTP_GET)?"GET":"POST";
  message += "nArguments: ";
  message += server.args();
  message += "n";
  for (uint8_t i=0; i<server.args(); i++){
    message += " " + server.argName(i) + ": " + server.arg(i) + "n";
  }
  server.send(404, "text/plain", message);
  digitalWrite(led, 0);
}
 
void setup(void){
  pinMode(led, OUTPUT);
  digitalWrite(led, 0);
  Serial.begin(115200);
  WiFi.begin(ssid, password);
  Serial.println("");
 
  // Wait for connection
  while (WiFi.status() != WL_CONNECTED) {
    delay(500);
    Serial.print(".");
  }
  Serial.println("");
  Serial.print("Connected to ");
  Serial.println(ssid);
  Serial.print("IP address: ");
  Serial.println(WiFi.localIP());
 
  if (MDNS.begin("esp8266")) {
    Serial.println("MDNS responder started");
  }
 
  server.on("/", handleRoot);
 
  server.on("/inline", [](){
    server.send(200, "text/plain", "this works as well");
  });
 
  server.onNotFound(handleNotFound);
 
  server.begin();
  Serial.println("HTTP server started");
}
 
void loop(void){
  server.handleClient();
}

ssid填写wifi名，password填写wifi密码