移植wpa_supplicant-2.6

最新推荐文章于 2022-11-17 09:09:04 发布

kuangzuxiaoN

最新推荐文章于 2022-11-17 09:09:04 发布

阅读量2.5k

点赞数 1

分类专栏： ARM + Linux 文章标签： wpa_supplicant-2.6 openssl-1.1.0f libnl-3.3.0

本文链接：https://blog.csdn.net/kuangzuxiaoN/article/details/75028643

版权

ARM + Linux 专栏收录该内容

13 篇文章 1 订阅

订阅专栏

开发环境： ubuntu 16.04LTS

目标环境： iTOP4412精英板

交叉编译器： arm-2014.05

到官网下载最新的版本wpa_supplicant-2.6

http://www.linuxfromscratch.org/blfs/view/svn/basicnet/wpa_supplicant.html

在官网可以看到wpa_supplicant-2.6的依赖程序

WPA Supplicant Dependencies

Recommended

libnl-3.3.0 and OpenSSL-1.1.0f

Optional

dbus-1.10.20, libxml2-2.9.4, and Qt-5.9.1

主要依赖于libnl-3.3.0和OpenSSL-1.1.0f，这里给出下载地址：

libnl-3.3.0: http://www.linuxfromscratch.org/blfs/view/svn/basicnet/libnl.html

OpenSSL-1.1.0f: http://www.linuxfromscratch.org/blfs/view/svn/postlfs/openssl.html

移植步骤：

（1）首先移植openssl-1.1.0f

1. 解压并进入到openssl-1.1.0f主目录

	tar -xvf openssl-1.1.0f
	cd openssl-1.1.0f

2. 执行

./Configure linux-armv4 --prefix=/usr/local/arm/openssl

配置目标环境，根据自己的板子具体修改，Exynos4412是armv7架构，并且给定路径参数，我要安装的绝对路径是/usr/local/arm/openssl

配置成功后，可以看到

Configuring for linux-armv4
CC            =gcc
CFLAG         =-Wall -O3 -pthread 
SHARED_CFLAG  =-fPIC -DOPENSSL_USE_NODELETE
DEFINES       =DSO_DLFCN HAVE_DLFCN_H NDEBUG OPENSSL_THREADS OPENSSL_NO_STATIC_ENGINE OPENSSL_PIC OPENSSL_BN_ASM_MONT OPENSSL_BN_ASM_GF2m SHA1_ASM SHA256_ASM SHA512_ASM AES_ASM BSAES_ASM GHASH_ASM ECP_NISTZ256_ASM POLY1305_ASM
LFLAG         =
PLIB_LFLAG    =
EX_LIBS       =-ldl 
APPS_OBJ      =
CPUID_OBJ     =armcap.o armv4cpuid.o
UPLINK_OBJ    =
BN_ASM        =bn_asm.o armv4-mont.o armv4-gf2m.o
EC_ASM        =ecp_nistz256.o ecp_nistz256-armv4.o
DES_ENC       =des_enc.o fcrypt_b.o
AES_ENC       =aes_cbc.o aes-armv4.o bsaes-armv7.o aesv8-armx.o
BF_ENC        =bf_enc.o
CAST_ENC      =c_enc.o
RC4_ENC       =rc4_enc.o rc4_skey.o
RC5_ENC       =rc5_enc.o
MD5_OBJ_ASM   =
SHA1_OBJ_ASM  =sha1-armv4-large.o sha256-armv4.o sha512-armv4.o
RMD160_OBJ_ASM=
CMLL_ENC      =camellia.o cmll_misc.o cmll_cbc.o
MODES_OBJ     =ghash-armv4.o ghashv8-armx.o
PADLOCK_OBJ   =
CHACHA_ENC    =chacha-armv4.o
POLY1305_OBJ  =poly1305-armv4.o
BLAKE2_OBJ    =
PROCESSOR     =
RANLIB        =ranlib
ARFLAGS       =
PERL          =/usr/bin/perl

THIRTY_TWO_BIT mode
BN_LLONG mode
RC4 uses unsigned char

Configured for linux-armv4.

3. 这里就需要修改交叉编译器，修改Makefile

添加交叉编译器：

CROSS_COMPILE=/usr/local/arm/arm-2014.05/bin/arm-none-linux-gnueabi-

配置参数中已经指定了路径，因此在Makefile不用修改，可以看到：

51: INSTALLTOP=/usr/local/arm/openssl
52: OPENSSLDIR=/usr/local/arm/openssl/ssl
53: LIBDIR=lib
54: ENGINESDIR=/usr/local/arm/openssl/lib/engines-1.1

4. 执行make，完成编译

5. 执行sudo make install，完成安装

6. 可以看到openssl被编译成静态库，放在指定目录/usr/local/arm/openssl下

yang@yang:/usr/local/arm/openssl$ ls
bin  include  lib  share  ssl
yang@yang:/usr/local/arm/openssl/lib$ ls
engines-1.1  libcrypto.so      libssl.a   libssl.so.1.1
libcrypto.a  libcrypto.so.1.1  libssl.so  pkgconfig
yang@yang:/usr/local/arm/openssl/lib$

7. 将lib中的libcrypto.a、libcrypto.so.1.1、libssl.so.1.1和libssl.a文件拷贝到开发板文件系统的/lib目录下，bin中的openssl文件拷贝到开发板的/bin中

可能出现错误（源自网络资源）：

installing man1/smime.1
　　smime.pod around line 272： Expected text after =item， not a number
　　smime.pod around line 276： Expected text after =item， not a number
　　smime.pod around line 280： Expected text after =item， not a number
　　smime.pod around line 285： Expected text after =item， not a number
　　smime.pod around line 289： Expected text after =item， not a number
　　POD document had syntax errors at /usr/bin/pod2man line 71.
　　make： *** ［install_docs］ 错误 255
　　原因分析：这是由于OpenSSL 1.0.1e 与 perl5.18 不兼容。
　　解决方法：
　　1、有人验证 安装perl 5.16 可以兼容，安排低版本perl 5.16可以解决问题。
　　2、删除 pod2man文件：
　　sudo rm /usr/bin/pod2man

（2）移植libnl-3.3.0

1.解压并进入到主目录

cd libnl-3.3.0

2.配置交叉编译选项

sudo ./configure --host=arm-linux --prefix=/usr/local/arm/libnl --enable-static --enable-shared CC=/usr/local/arm/arm-2014.05/bin/arm-none-linux-gnueabi-gcc

在这里交叉编译器用的是绝对路径。

可能会出现如下错误：

configure: WARNING: bison not found. Please install before continuing.
configure: WARNING: flex not found. Please install before continuing.
configure: error: Required packages are missing. Please install them and rerun ./configure

根据提示，安装bison和flex

sudo apt-get install bison
sudo apt-get install flex

再次使用配置编译选项命令，最终看到如下输出

-------------------------------------------------------------------------------
                                  NOTE

 There have been some changes starting with 3.2 regarding where and how libnl
 is being installed on the system in order to allow multiple libnl versions
 to be installed in parallel:

    - Headers will be installed in ${prefix}/include/libnl3, therefore
      you will need to add "-I/usr/include/libnl3" to CFLAGS

    - The library basename was renamed to libnl-3, i.e. the SO names become
      libnl-3.so., libnl-route-3.so, etc.

    - libtool versioning was assumed, to ease detection of compatible library
      versions.

 If you are using pkg-config for detecting and linking against the library 
 things will continue magically as if nothing every happened. If you are 
 linking manually you need to adapt your Makefiles or switch to using 
 pkg-config files.

-------------------------------------------------------------------------------

配置成功。

3. 开始编译，执行make命令

4. 安装，执行make install命令

在/usr/local/arm/libnl目录下有以下文件

yang@yang:/usr/local/arm/libnl$ ls
bin  etc  include  lib  share
yang@yang:/usr/local/arm/libnl$ ls lib/
libnl                    libnl-genl-3.so            libnl-route-3.a
libnl-3.a                libnl-genl-3.so.200        libnl-route-3.la
libnl-3.la               libnl-genl-3.so.200.25.0   libnl-route-3.so
libnl-3.so               libnl-idiag-3.a            libnl-route-3.so.200
libnl-3.so.200           libnl-idiag-3.la           libnl-route-3.so.200.25.0
libnl-3.so.200.25.0      libnl-idiag-3.so           libnl-xfrm-3.a
libnl-cli-3.a            libnl-idiag-3.so.200       libnl-xfrm-3.la
libnl-cli-3.la           libnl-idiag-3.so.200.25.0  libnl-xfrm-3.so
libnl-cli-3.so           libnl-nf-3.a               libnl-xfrm-3.so.200
libnl-cli-3.so.200       libnl-nf-3.la              libnl-xfrm-3.so.200.25.0
libnl-cli-3.so.200.25.0  libnl-nf-3.so              pkgconfig
libnl-genl-3.a           libnl-nf-3.so.200
libnl-genl-3.la          libnl-nf-3.so.200.25.0

5. 安装成功，将libnl-3.so.200.25.0、libnl-genl-3.so.200.25.0放到开发板的/lib目录，并创建软链接

ln -s libnl-3.so.200.25.0 libnl-3.so
ln -s libnl-3.so.200.25.0 libnl-3.so.200
ln -s libnl-genl-3.so.200.25.0 libnl-genl-3.so
ln -s libnl-genl-3.so.200.25.0 libnl-genl-3.so.200

（3）移植wpa_supplicant-2.6

1. 解压并进入到wpa_supplicant-2.6主目录，并生成.config文件

cd wpa_supplicant-2.6
cp defconfig .config

2. 修改.config文件

CC=/usr/local/arm/arm-2014.05/bin/arm-none-linux-gnueabi-gcc -L/usr/local/arm/openssl/lib
CFLAGS += -I/usr/local/arm/openssl/include
LIBS += -L/usr/local/arm/openssl/lib
 
CONFIG_DRIVER_NL80211=y

CONFIG_LIBNL32=y
CFLAGS += -I/usr/local/arm/libnl/include
LIBS += -L/usr/local/arm/libnl/lib

这里只给出主要的修改部分，其他使用默认设置就好。注意，这里一定要添加libnl的配置，否则会出现错误：

../src/drivers/driver_nl80211.c:17:31: fatal error: netlink/genl/genl.h: No such file or directory
 #include <netlink/genl/genl.h>
                               ^
compilation terminated.
Makefile:1776: recipe for target '../src/drivers/driver_nl80211.o' failed
make: *** [../src/drivers/driver_nl80211.o] Error 1

3. 编译，执行make
4. 将生成的wpa_cli、wpa_passphrase、 wpa_supplicant等工具添加到开发板文件系统/bin目录下，并且拷贝配置文件到开发板文件系统/etc目录下。

cp examples/wpa-psk-tkip.conf rootfs/etc/wpa_supplicant.conf

5. 修改wpa_supplicant.conf

# WPA-PSK/TKIP

ctrl_interface=/var/run/wpa_supplicant

network={
        ssid="yang"		#无线网络名称
        key_mgmt=WPA-PSK
        proto=WPA
        pairwise=TKIP
        group=TKIP
        psk="57b559b778"	#无线网络密码
}

（4）测试wpa_supplicant

1. 在开发板的/var/run/下创建文件wpa_supplicant

mkdir -p wpa_supplicant

2. 使用命令：

wpa_passphrase yang 57b559b778 >> wpa_supplicant.conf

创建连接暗文密码(PSK密码)，通过明码转换，修改wpa_supplicant.conf，用PSK密码替换明文密码

# WPA-PSK/TKIP

ctrl_interface=/var/run/wpa_supplicant

network={
        ssid="yang"
        key_mgmt=WPA-PSK
        proto=WPA
        pairwise=TKIP
        group=TKIP
        psk=725e926081647954f9af00e46904fd6382b2cbc91b8ab7b5655a8d8db146c5dc
}

3. 在开发板的终端命令行使用命令wpa_supplicant，出现如下信息，说明wpa_supplicant移植成功

Successfully initialized wpa_supplicant
wpa_supplicant v2.6
Copyright (c) 2003-2016, Jouni Malinen <j@w1.fi> and contributors

This software may be distributed under the terms of the BSD license.
See README for more details.

This product includes software developed by the OpenSSL Project
for use in the OpenSSL Toolkit (http://www.openssl.org/)

usage:
  wpa_supplicant [-BddhKLqqtvW] [-P<pid file>] [-g<global ctrl>] \
        [-G<group>] \
        -i<ifname> -c<config file> [-C<ctrl>] [-D<driver>] [-p<driver_param>] \
        [-b<br_ifname>] [-e<entropy file>] \
        [-o<override driver>] [-O<override ctrl>] \
        [-N -i<ifname> -c<conf> [-C<ctrl>] [-D<driver>] \
        [-p<driver_param>] [-b<br_ifname>] [-I<config file>] ...]

drivers:
  nl80211 = Linux nl80211/cfg80211
  wext = Linux wireless extensions (generic)
  wired = Wired Ethernet driver
options:
  -b = optional bridge interface name
  -B = run daemon in the background
  -c = Configuration file
  -C = ctrl_interface parameter (only used if -c is not)
  -d = increase debugging verbosity (-dd even more)
  -D = driver name (can be multiple drivers: nl80211,wext)
  -e = entropy file
  -g = global ctrl_interface
  -G = global ctrl_interface group
  -h = show this help text
  -i = interface name
  -I = additional configuration file
  -K = include keys (passwords, etc.) in debug output
  -L = show license (BSD)
  -N = start describing new interface
  -o = override driver parameter for new interfaces
  -O = override ctrl_interface parameter for new interfaces
  -p = driver parameters
  -P = PID file
  -q = decrease debugging verbosity (-qq even less)
  -t = include timestamp in debug messages
  -v = show version
  -W = wait for a control interface monitor before starting
example:
  wpa_supplicant -Dnl80211 -iwlan0 -c/etc/wpa_supplicant.conf

4. 加载网卡驱动，并且配置IP地址

ifconfig wlan0 up
ifconfig wlan0 10.42.0.12 netmask 255.255.255.0

注意：此处设置的IP需要与你将要连接的局域网IP在同一网段，或者是直接移植DHCP

5. 用ifconfig命令查看无线网卡

eth0      Link encap:Ethernet  HWaddr 08:90:90:90:90:90  
          inet addr:192.168.1.230  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::a90:90ff:fe90:9090/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:19520 errors:0 dropped:123 overruns:0 frame:0
          TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:1323355 (1.2 MiB)  TX bytes:480 (480.0 B)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wlan0     Link encap:Ethernet  HWaddr 48:8A:D2:3A:9E:24  
          inet addr:10.42.0.12  Bcast:10.42.0.255  Mask:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

6. 加载网卡成功，连接无线局域网

这里根据wpa_supplicant命令的提示，使用提示命令

wpa_supplicant -Dnl80211 -iwlan0 -c/etc/wpa_supplicant.conf

会出现如下错误：

nl80211: deinit ifname=wlan0 disabled_11b_rates=0
wlan0: Failed to initialize driver interface

可见wlan0驱动不支持Linux nl80211/cfg80211，因此改用

wpa_supplicant -Dwext -iwlan0 -c/etc/wpa_supplicant.conf

注：关于nl80211和wext无线驱动接口的区别

nl80211 = Linux nl80211/cfg80211

wext = Linux wireless extensions (generic)

可参考： http://blog.csdn.net/dickjtk/article/details/11862815

7. 测试无线局域网，将要连接的无线网IP: 10.42.0.1

PING 10.42.0.1 (10.42.0.1): 56 data bytes
64 bytes from 10.42.0.1: seq=0 ttl=64 time=8.918 ms
64 bytes from 10.42.0.1: seq=1 ttl=64 time=1.402 ms
64 bytes from 10.42.0.1: seq=2 ttl=64 time=1.315 ms
64 bytes from 10.42.0.1: seq=3 ttl=64 time=3.993 ms
64 bytes from 10.42.0.1: seq=4 ttl=64 time=3.141 ms
64 bytes from 10.42.0.1: seq=5 ttl=64 time=2.574 ms
64 bytes from 10.42.0.1: seq=6 ttl=64 time=2.136 ms
64 bytes from 10.42.0.1: seq=7 ttl=64 time=1.561 ms
^C
--- 10.42.0.1 ping statistics ---
8 packets transmitted, 8 packets received, 0% packet loss
round-trip min/avg/max = 1.315/3.130/8.918 ms

网络连接成功。