基于STM32的智能衣柜设计2（超级详细代码）

1.OLED

oled.c

#include "stm32f10x.h"
#include "oled.h"
#include "stdlib.h"
#include "oledfont.h"  	 
#include "delay.h"

u8 OLED_GRAM[144][4];

//·´ÏÔº¯Êý
void OLED_ColorTurn(u8 i)
{
	if(i==0)
		{
			OLED_WR_Byte(0xA6,OLED_CMD);//Õý³£ÏÔʾ
		}
	if(i==1)
		{
			OLED_WR_Byte(0xA7,OLED_CMD);//·´É«ÏÔʾ
		}
}

//ÆÁÄ»Ðýת180¶È
void OLED_DisplayTurn(u8 i)
{
	if(i==0)
		{
			OLED_WR_Byte(0xC8,OLED_CMD);//Õý³£ÏÔʾ
			OLED_WR_Byte(0xA1,OLED_CMD);
		}
	if(i==1)
		{
			OLED_WR_Byte(0xC0,OLED_CMD);//·´×ªÏÔʾ
			OLED_WR_Byte(0xA0,OLED_CMD);
		}
}

//ÑÓʱ
void IIC_delay(void)
{
	u8 t=3;
	while(t--);
}

//ÆðʼÐźÅ
void I2C_Start(void)
{
	OLED_SDA_Set();
	OLED_SCL_Set();
	IIC_delay();
	OLED_SDA_Clr();
	IIC_delay();
	OLED_SCL_Clr();
	IIC_delay();
}

//½áÊøÐźÅ
void I2C_Stop(void)
{
	OLED_SDA_Clr();
	OLED_SCL_Set();
	IIC_delay();
	OLED_SDA_Set();
}

//µÈ´ýÐźÅÏìÓ¦
void I2C_WaitAck(void) //²âÊý¾ÝÐźŵĵçƽ
{
	OLED_SDA_Set();
	IIC_delay();
	OLED_SCL_Set();
	IIC_delay();
	OLED_SCL_Clr();
	IIC_delay();
}

//дÈëÒ»¸ö×Ö½Ú
void Send_Byte(u8 dat)
{
	u8 i;
	for(i=0;i<8;i++)
	{
		if(dat&0x80)//½«datµÄ8λ´Ó×î¸ßλÒÀ´ÎдÈë
		{
			OLED_SDA_Set();
    }
		else
		{
			OLED_SDA_Clr();
    }
		IIC_delay();
		OLED_SCL_Set();
		IIC_delay();
		OLED_SCL_Clr();//½«Ê±ÖÓÐźÅÉèÖÃΪµÍµçƽ
		dat<<=1;
  }
}

//·¢ËÍÒ»¸ö×Ö½Ú
//mode:Êý¾Ý/ÃüÁî±êÖ¾ 0,±íʾÃüÁî;1,±íʾÊý¾Ý;
void OLED_WR_Byte(u8 dat,u8 mode)
{
	I2C_Start();
	Send_Byte(0x78);
	I2C_WaitAck();
	if(mode){Send_Byte(0x40);}
  else{Send_Byte(0x00);}
	I2C_WaitAck();
	Send_Byte(dat);
	I2C_WaitAck();
	I2C_Stop();
}

//¿ªÆôOLEDÏÔʾ 
void OLED_DisPlay_On(void)
{
	OLED_WR_Byte(0x8D,OLED_CMD);//µçºÉ±ÃʹÄÜ
	OLED_WR_Byte(0x14,OLED_CMD);//¿ªÆôµçºÉ±Ã
	OLED_WR_Byte(0xAF,OLED_CMD);//µãÁÁÆÁÄ»
}

//¹Ø±ÕOLEDÏÔʾ 
void OLED_DisPlay_Off(void)
{
	OLED_WR_Byte(0x8D,OLED_CMD);//µçºÉ±ÃʹÄÜ
	OLED_WR_Byte(0x10,OLED_CMD);//¹Ø±ÕµçºÉ±Ã
	OLED_WR_Byte(0xAE,OLED_CMD);//¹Ø±ÕÆÁÄ»
}

//¸üÐÂÏÔ´æµ½OLED	
void OLED_Refresh(void)
{
	u8 i,n;
	for(i=0;i<4;i++)
	{
		OLED_WR_Byte(0xb0+i,OLED_CMD); //ÉèÖÃÐÐÆðʼµØÖ·
		OLED_WR_Byte(0x00,OLED_CMD);   //ÉèÖõÍÁÐÆðʼµØÖ·
		OLED_WR_Byte(0x10,OLED_CMD);   //ÉèÖøßÁÐÆðʼµØÖ·
		I2C_Start();
		Send_Byte(0x78);
		I2C_WaitAck();
		Send_Byte(0x40);
		I2C_WaitAck();
		for(n=0;n<128;n++)
		{
			Send_Byte(OLED_GRAM[n][i]);
			I2C_WaitAck();
		}
		I2C_Stop();
  }
}
//ÇåÆÁº¯Êý
void OLED_Clear(void)
{
	u8 i,n;
	for(i=0;i<4;i++)
	{
	   for(n=0;n<128;n++)
			{
			 OLED_GRAM[n][i]=0;//Çå³ýËùÓÐÊý¾Ý
			}
  }
	OLED_Refresh();//¸üÐÂÏÔʾ
}

//»­µã 
//x:0~127
//y:0~63
//t:1 Ìî³ä 0,Çå¿Õ	
void OLED_DrawPoint(u8 x,u8 y,u8 t)
{
	u8 i,m,n;
	i=y/8;
	m=y%8;
	n=1<<m;
	if(t){OLED_GRAM[x][i]|=n;}
	else
	{
		OLED_GRAM[x][i]=~OLED_GRAM[x][i];
		OLED_GRAM[x][i]|=n;
		OLED_GRAM[x][i]=~OLED_GRAM[x][i];
	}
}

//»­Ïß
//x1,y1:Æðµã×ø±ê
//x2,y2:½áÊø×ø±ê
void OLED_DrawLine(u8 x1,u8 y1,u8 x2,u8 y2,u8 mode)
{
	u16 t; 
	int xerr=0,yerr=0,delta_x,delta_y,distance;
	int incx,incy,uRow,uCol;
	delta_x=x2-x1; //¼ÆËã×ø±êÔöÁ¿ 
	delta_y=y2-y1;
	uRow=x1;//»­ÏßÆðµã×ø±ê
	uCol=y1;
	if(delta_x>0)incx=1; //ÉèÖõ¥²½·½Ïò 
	else if (delta_x==0)incx=0;//´¹Ö±Ïß 
	else {incx=-1;delta_x=-delta_x;}
	if(delta_y>0)incy=1;
	else if (delta_y==0)incy=0;//ˮƽÏß 
	else {incy=-1;delta_y=-delta_x;}
	if(delta_x>delta_y)distance=delta_x; //Ñ¡È¡»ù±¾ÔöÁ¿×ø±êÖá 
	else distance=delta_y;
	for(t=0;t<distance+1;t++)
	{
		OLED_DrawPoint(uRow,uCol,mode);//»­µã
		xerr+=delta_x;
		yerr+=delta_y;
		if(xerr>distance)
		{
			xerr-=distance;
			uRow+=incx;
		}
		if(yerr>distance)
		{
			yerr-=distance;
			uCol+=incy;
		}
	}
}
//x,y:Ô²ÐÄ×ø±ê
//r:Ô²µÄ°ë¾¶
void OLED_DrawCircle(u8 x,u8 y,u8 r)
{
	int a, b,num;
    a = 0;
    b = r;
    while(2 * b * b >= r * r)      
    {
        OLED_DrawPoint(x + a, y - b,1);
        OLED_DrawPoint(x - a, y - b,1);
        OLED_DrawPoint(x - a, y + b,1);
        OLED_DrawPoint(x + a, y + b,1);
 
        OLED_DrawPoint(x + b, y + a,1);
        OLED_DrawPoint(x + b, y - a,1);
        OLED_DrawPoint(x - b, y - a,1);
        OLED_DrawPoint(x - b, y + a,1);
        
        a++;
        num = (a * a + b * b) - r*r;//¼ÆËã»­µÄµãÀëÔ²ÐĵľàÀë
        if(num > 0)
        {
            b--;
            a--;
        }
    }
}



//ÔÚÖ¸¶¨Î»ÖÃÏÔʾһ¸ö×Ö·û,°üÀ¨²¿·Ö×Ö·û
//x:0~127
//y:0~63
//size1:Ñ¡Ôñ×ÖÌå 6x8/6x12/8x16/12x24
//mode:0,·´É«ÏÔʾ;1,Õý³£ÏÔʾ
void OLED_ShowChar(u8 x,u8 y,u8 chr,u8 size1,u8 mode)
{
	u8 i,m,temp,size2,chr1;
	u8 x0=x,y0=y;
	if(size1==8)size2=6;
	else size2=(size1/8+((size1%8)?1:0))*(size1/2);  //µÃµ½×ÖÌåÒ»¸ö×Ö·û¶ÔÓ¦µãÕó¼¯ËùÕ¼µÄ×Ö½ÚÊý
	chr1=chr-' ';  //¼ÆËãÆ«ÒƺóµÄÖµ
	for(i=0;i<size2;i++)
	{
		if(size1==8)
			  {temp=asc2_0806[chr1][i];} //µ÷ÓÃ0806×ÖÌå
		else if(size1==12)
        {temp=asc2_1206[chr1][i];} //µ÷ÓÃ1206×ÖÌå
		else if(size1==16)
        {temp=asc2_1608[chr1][i];} //µ÷ÓÃ1608×ÖÌå
		else if(size1==24)
        {temp=asc2_2412[chr1][i];} //µ÷ÓÃ2412×ÖÌå
		else return;
		for(m=0;m<8;m++)
		{
			if(temp&0x01)OLED_DrawPoint(x,y,mode);
			else OLED_DrawPoint(x,y,!mode);
			temp>>=1;
			y++;
		}
		x++;
		if((size1!=8)&&((x-x0)==size1/2))
		{x=x0;y0=y0+8;}
		y=y0;
  }
}


//ÏÔʾ×Ö·û´®
//x,y:Æðµã×ø±ê  
//size1:×ÖÌå´óС 
//*chr:×Ö·û´®ÆðʼµØÖ· 
//mode:0,·´É«ÏÔʾ;1,Õý³£ÏÔʾ
void OLED_ShowString(u8 x,u8 y,u8 *chr,u8 size1,u8 mode)
{
	while((*chr>=' ')&&(*chr<='~'))//ÅжÏÊDz»ÊÇ·Ç·¨×Ö·û!
	{
		OLED_ShowChar(x,y,*chr,size1,mode);
		if(size1==8)x+=6;
		else x+=size1/2;
		chr++;
  }
}

//m^n
u32 OLED_Pow(u8 m,u8 n)
{
	u32 result=1;
	while(n--)
	{
	  result*=m;
	}
	return result;
}

//ÏÔʾÊý×Ö
//x,y :Æðµã×ø±ê	 
//len :Êý×ÖµÄλÊý
//size:×ÖÌå´óС
//mode:0,·´É«ÏÔʾ;1,Õý³£ÏÔʾ
void OLED_ShowNum(u8 x,u8 y,u32 num,u8 len,u8 size1,u8 mode)
{
	u8 t,temp,m=0;
	if(size1==8)m=2;
	for(t=0;t<len;t++)
	{
		temp=(num/OLED_Pow(10,len-t-1))%10;
			if(temp==0)
			{
				OLED_ShowChar(x+(size1/2+m)*t,y,'0',size1,mode);
      }
			else 
			{
			  OLED_ShowChar(x+(size1/2+m)*t,y,temp+'0',size1,mode);
			}
  }
}

//ÏÔʾºº×Ö
//x,y:Æðµã×ø±ê
//num:ºº×Ö¶ÔÓ¦µÄÐòºÅ
//mode:0,·´É«ÏÔʾ;1,Õý³£ÏÔʾ
void OLED_ShowChinese(u8 x,u8 y,u8 num,u8 size1,u8 mode)
{
	u8 m,temp;
	u8 x0=x,y0=y;
	u16 i,size3=(size1/8+((size1%8)?1:0))*size1;  //µÃµ½×ÖÌåÒ»¸ö×Ö·û¶ÔÓ¦µãÕó¼¯ËùÕ¼µÄ×Ö½ÚÊý
	for(i=0;i<size3;i++)
	{
		if(size1==16)
				{temp=Hzk1[num][i];}//µ÷ÓÃ16*16×ÖÌå
		else if(size1==24)
				{temp=Hzk2[num][i];}//µ÷ÓÃ24*24×ÖÌå
		else if(size1==32)       
				{temp=Hzk3[num][i];}//µ÷ÓÃ32*32×ÖÌå
		else if(size1==64)
				{temp=Hzk4[num][i];}//µ÷ÓÃ64*64×ÖÌå
		else return;
		for(m=0;m<8;m++)
		{
			if(temp&0x01)OLED_DrawPoint(x,y,mode);
			else OLED_DrawPoint(x,y,!mode);
			temp>>=1;
			y++;
		}
		x++;
		if((x-x0)==size1)
		{x=x0;y0=y0+8;}
		y=y0;
	}
}

//num ÏÔʾºº×ֵĸöÊý
//space ÿһ±éÏÔʾµÄ¼ä¸ô
//mode:0,·´É«ÏÔʾ;1,Õý³£ÏÔʾ
void OLED_ScrollDisplay(u8 num,u8 space,u8 mode)
{
	u8 i,n,t=0,m=0,r;
	while(1)
	{
		if(m==0)
		{
	    OLED_ShowChinese(128,8,t,16,mode); //дÈëÒ»¸öºº×Ö±£´æÔÚOLED_GRAM[][]Êý×éÖÐ
			t++;
		}
		if(t==num)
			{
				for(r=0;r<16*space;r++)      //ÏÔʾ¼ä¸ô
				 {
					for(i=1;i<144;i++)
						{
							for(n=0;n<4;n++)
							{
								OLED_GRAM[i-1][n]=OLED_GRAM[i][n];
							}
						}
           OLED_Refresh();
				 }
        t=0;
      }
		m++;
		if(m==16){m=0;}
		for(i=1;i<144;i++)   //ʵÏÖ×óÒÆ
		{
			for(n=0;n<4;n++)
			{
				OLED_GRAM[i-1][n]=OLED_GRAM[i][n];
			}
		}
		OLED_Refresh();
	}
}

//x,y£ºÆðµã×ø±ê
//sizex,sizey,ͼƬ³¤¿í
//BMP[]£ºÒªÐ´ÈëµÄͼƬÊý×é
//mode:0,·´É«ÏÔʾ;1,Õý³£ÏÔʾ
void OLED_ShowPicture(u8 x,u8 y,u8 sizex,u8 sizey,u8 BMP[],u8 mode)
{
	u16 j=0;
	u8 i,n,temp,m;
	u8 x0=x,y0=y;
	sizey=sizey/8+((sizey%8)?1:0);
	for(n=0;n<sizey;n++)
	{
		 for(i=0;i<sizex;i++)
		 {
				temp=BMP[j];
				j++;
				for(m=0;m<8;m++)
				{
					if(temp&0x01)OLED_DrawPoint(x,y,mode);
					else OLED_DrawPoint(x,y,!mode);
					temp>>=1;
					y++;
				}
				x++;
				if((x-x0)==sizex)
				{
					x=x0;
					y0=y0+8;
				}
				y=y0;
     }
	 }
}


//OLEDµÄ³õʼ»¯
void OLED_Init(void)
{
	GPIO_InitTypeDef  GPIO_InitStructure;
 	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOG|RCC_APB2Periph_GPIOD, ENABLE);	 //ʹÄÜA¶Ë¿ÚʱÖÓ
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_12;	 
 	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_OD; 		 //ÍÆÍìÊä³ö
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;//ËÙ¶È50MHz
 	GPIO_Init(GPIOG, &GPIO_InitStructure);	  //³õʼ»¯GPIOG12
 	GPIO_SetBits(GPIOG,GPIO_Pin_12);
	
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5;
 	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_OD; 		 //ÍÆÍìÊä³ö
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;//ËÙ¶È50MHz
 	GPIO_Init(GPIOD, &GPIO_InitStructure);	  //³õʼ»¯GPIOD1,5,15
 	GPIO_SetBits(GPIOD,GPIO_Pin_5);
	
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_4;
 	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP; 		 //ÍÆÍìÊä³ö
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;//ËÙ¶È50MHz
 	GPIO_Init(GPIOD, &GPIO_InitStructure);	  //³õʼ»¯GPIOD1,5,15
 	GPIO_SetBits(GPIOD,GPIO_Pin_4);
	
	OLED_RES_Clr();
	delay_ms(200);
	OLED_RES_Set();
	
	OLED_WR_Byte(0xAE,OLED_CMD); /*display off*/
	OLED_WR_Byte(0x00,OLED_CMD); /*set lower column address*/ 
	OLED_WR_Byte(0x10,OLED_CMD); /*set higher column address*/
	OLED_WR_Byte(0x00,OLED_CMD); /*set display start line*/ 
	OLED_WR_Byte(0xB0,OLED_CMD); /*set page address*/ 
	OLED_WR_Byte(0x81,OLED_CMD); /*contract control*/ 
	OLED_WR_Byte(0xff,OLED_CMD); /*128*/ 
	OLED_WR_Byte(0xA1,OLED_CMD); /*set segment remap*/ 
	OLED_WR_Byte(0xA6,OLED_CMD); /*normal / reverse*/ 
	OLED_WR_Byte(0xA8,OLED_CMD); /*multiplex ratio*/ 
	OLED_WR_Byte(0x1F,OLED_CMD); /*duty = 1/32*/ 
	OLED_WR_Byte(0xC8,OLED_CMD); /*Com scan direction*/ 
	OLED_WR_Byte(0xD3,OLED_CMD); /*set display offset*/ 
	OLED_WR_Byte(0x00,OLED_CMD); 
	OLED_WR_Byte(0xD5,OLED_CMD); /*set osc division*/ 
	OLED_WR_Byte(0x80,OLED_CMD); 
	OLED_WR_Byte(0xD9,OLED_CMD); /*set pre-charge period*/ 
	OLED_WR_Byte(0x1f,OLED_CMD); 
	OLED_WR_Byte(0xDA,OLED_CMD); /*set COM pins*/ 
	OLED_WR_Byte(0x00,OLED_CMD); 
	OLED_WR_Byte(0xdb,OLED_CMD); /*set vcomh*/ 
	OLED_WR_Byte(0x40,OLED_CMD); 
	OLED_WR_Byte(0x8d,OLED_CMD); /*set charge pump enable*/ 
	OLED_WR_Byte(0x14,OLED_CMD);
	OLED_Clear();
	OLED_WR_Byte(0xAF,OLED_CMD); /*display ON*/
}

oled.h

#ifndef __OLED_H
#define __OLED_H 

#include "sys.h"
#include "stdlib.h"	

//-----------------OLED¶Ë¿Ú¶¨Òå---------------- 

#define OLED_SCL_Clr() GPIO_ResetBits(GPIOG,GPIO_Pin_12)//SCL
#define OLED_SCL_Set() GPIO_SetBits(GPIOG,GPIO_Pin_12)

#define OLED_SDA_Clr() GPIO_ResetBits(GPIOD,GPIO_Pin_5)//DIN
#define OLED_SDA_Set() GPIO_SetBits(GPIOD,GPIO_Pin_5)

#define OLED_RES_Clr() GPIO_ResetBits(GPIOD,GPIO_Pin_4)//RES
#define OLED_RES_Set() GPIO_SetBits(GPIOD,GPIO_Pin_4)


#define OLED_CMD  0	//дÃüÁî
#define OLED_DATA 1	//дÊý¾Ý

void OLED_ClearPoint(u8 x,u8 y);
void OLED_ColorTurn(u8 i);
void OLED_DisplayTurn(u8 i);
void I2C_Start(void);
void I2C_Stop(void);
void I2C_WaitAck(void);
void Send_Byte(u8 dat);
void OLED_WR_Byte(u8 dat,u8 mode);
void OLED_DisPlay_On(void);
void OLED_DisPlay_Off(void);
void OLED_Refresh(void);
void OLED_Clear(void);
void OLED_DrawPoint(u8 x,u8 y,u8 t);
void OLED_DrawLine(u8 x1,u8 y1,u8 x2,u8 y2,u8 mode);
void OLED_DrawCircle(u8 x,u8 y,u8 r);
void OLED_ShowChar(u8 x,u8 y,u8 chr,u8 size1,u8 mode);
void OLED_ShowChar6x8(u8 x,u8 y,u8 chr,u8 mode);
void OLED_ShowString(u8 x,u8 y,u8 *chr,u8 size1,u8 mode);
void OLED_ShowNum(u8 x,u8 y,u32 num,u8 len,u8 size1,u8 mode);
void OLED_ShowChinese(u8 x,u8 y,u8 num,u8 size1,u8 mode);
void OLED_ScrollDisplay(u8 num,u8 space,u8 mode);
void OLED_ShowPicture(u8 x,u8 y,u8 sizex,u8 sizey,u8 BMP[],u8 mode);
void OLED_Init(void);

#endif

2.EXIT

exit.c

#include "exti.h"
#include "led.h"
#include "key.h"
#include "delay.h"
#include "usart.h"
#include "beep.h"
#include "dht11.h"
#include "MOTOR.h"
#include "oled.h"

void EXTIX_Init(void)
{
 
 	EXTI_InitTypeDef EXTI_InitStructure;
 	NVIC_InitTypeDef NVIC_InitStructure;

    KEY_Init();	 //	°´¼ü¶Ë¿Ú³õʼ»¯

  	RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO,ENABLE);	//ʹÄܸ´Óù¦ÄÜʱÖÓ

    //GPIOE.2 ÖжÏÏßÒÔ¼°Öжϳõʼ»¯ÅäÖà   ϽµÑØ´¥·¢
  	GPIO_EXTILineConfig(GPIO_PortSourceGPIOE,GPIO_PinSource2);

  	EXTI_InitStructure.EXTI_Line=EXTI_Line2;	//KEY2
  	EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt;	
  	EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling;
  	EXTI_InitStructure.EXTI_LineCmd = ENABLE;
  	EXTI_Init(&EXTI_InitStructure);	 	//¸ù¾ÝEXTI_InitStructÖÐÖ¸¶¨µÄ²ÎÊý³õʼ»¯ÍâÉèEXTI¼Ä´æÆ÷

   //GPIOE.3	  ÖжÏÏßÒÔ¼°Öжϳõʼ»¯ÅäÖà ϽµÑØ´¥·¢ //KEY1
  	GPIO_EXTILineConfig(GPIO_PortSourceGPIOE,GPIO_PinSource3);
  	EXTI_InitStructure.EXTI_Line=EXTI_Line3;
  	EXTI_Init(&EXTI_InitStructure);	  	//¸ù¾ÝEXTI_InitStructÖÐÖ¸¶¨µÄ²ÎÊý³õʼ»¯ÍâÉèEXTI¼Ä´æÆ÷

   //GPIOE.4	  ÖжÏÏßÒÔ¼°Öжϳõʼ»¯ÅäÖà  Ï½µÑØ´¥·¢	//KEY0
  	GPIO_EXTILineConfig(GPIO_PortSourceGPIOE,GPIO_PinSource4);
  	EXTI_InitStructure.EXTI_Line=EXTI_Line4;
  	EXTI_Init(&EXTI_InitStructure);	  	//¸ù¾ÝEXTI_InitStructÖÐÖ¸¶¨µÄ²ÎÊý³õʼ»¯ÍâÉèEXTI¼Ä´æÆ÷


   //GPIOA.0	  ÖжÏÏßÒÔ¼°Öжϳõʼ»¯ÅäÖà ÉÏÉýÑØ´¥·¢ PA0  WK_UP
 	 GPIO_EXTILineConfig(GPIO_PortSourceGPIOA,GPIO_PinSource0); 

  	EXTI_InitStructure.EXTI_Line=EXTI_Line0;
  	EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Rising;
  	EXTI_Init(&EXTI_InitStructure);		//¸ù¾ÝEXTI_InitStructÖÐÖ¸¶¨µÄ²ÎÊý³õʼ»¯ÍâÉèEXTI¼Ä´æÆ÷


  	NVIC_InitStructure.NVIC_IRQChannel = EXTI0_IRQn;			//ʹÄÜ°´¼üWK_UPËùÔÚµÄÍⲿÖжÏͨµÀ
  	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x02;	//ÇÀÕ¼ÓÅÏȼ¶2£¬ 
  	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x03;					//×ÓÓÅÏȼ¶3
  	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;								//ʹÄÜÍⲿÖжÏͨµÀ
  	NVIC_Init(&NVIC_InitStructure); 

    NVIC_InitStructure.NVIC_IRQChannel = EXTI2_IRQn;			//ʹÄÜ°´¼üKEY2ËùÔÚµÄÍⲿÖжÏͨµÀ
  	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x02;	//ÇÀÕ¼ÓÅÏȼ¶2£¬ 
  	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x02;					//×ÓÓÅÏȼ¶2
  	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;								//ʹÄÜÍⲿÖжÏͨµÀ
  	NVIC_Init(&NVIC_InitStructure);


  	NVIC_InitStructure.NVIC_IRQChannel = EXTI3_IRQn;			//ʹÄÜ°´¼üKEY1ËùÔÚµÄÍⲿÖжÏͨµÀ
  	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x02;	//ÇÀÕ¼ÓÅÏȼ¶2 
  	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x01;					//×ÓÓÅÏȼ¶1 
  	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;								//ʹÄÜÍⲿÖжÏͨµÀ
  	NVIC_Init(&NVIC_InitStructure);  	  //¸ù¾ÝNVIC_InitStructÖÐÖ¸¶¨µÄ²ÎÊý³õʼ»¯ÍâÉèNVIC¼Ä´æÆ÷

	NVIC_InitStructure.NVIC_IRQChannel = EXTI4_IRQn;			//ʹÄÜ°´¼üKEY0ËùÔÚµÄÍⲿÖжÏͨµÀ
  	NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0x02;	//ÇÀÕ¼ÓÅÏȼ¶2 
  	NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0x00;					//×ÓÓÅÏȼ¶0 
  	NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;								//ʹÄÜÍⲿÖжÏͨµÀ
  	NVIC_Init(&NVIC_InitStructure);  	  //¸ù¾ÝNVIC_InitStructÖÐÖ¸¶¨µÄ²ÎÊý³õʼ»¯ÍâÉèNVIC¼Ä´æÆ÷
 
}
u8 T_max = 30;
u8 h_max=80;
u8 T_num[12],H_num[12],temp_num[12],humi_num[12];
u8 temp,humi;
//ÍⲿÖжÏ0·þÎñ³ÌÐò 
void EXTI0_IRQHandler(void)
{
	delay_ms(10);//Ïû¶¶
	if(WK_UP==1)	 	 //WK_UP°´¼ü
	{				 
//		BEEP=!BEEP;	
		T_max=T_max+1;
	}
	EXTI_ClearITPendingBit(EXTI_Line0); //Çå³ýLINE0ÉϵÄÖжϱê־λ  
}
 
//ÍⲿÖжÏ2·þÎñ³ÌÐò
void EXTI2_IRQHandler(void)
{
	delay_ms(10);//Ïû¶¶
	if(KEY2==0)	  //°´¼üKEY2
	{
//		LED0=!LED0;
		T_max=T_max-1;
	}		 
	EXTI_ClearITPendingBit(EXTI_Line2);  //Çå³ýLINE2ÉϵÄÖжϱê־λ  
}
//ÍⲿÖжÏ3·þÎñ³ÌÐò
void EXTI3_IRQHandler(void)
{
	delay_ms(10);//Ïû¶¶
	if(KEY1==0)	 //°´¼üKEY1
	{				 
//		LED1=!LED1;
		h_max=h_max+1;
	}		 
	EXTI_ClearITPendingBit(EXTI_Line3);  //Çå³ýLINE3ÉϵÄÖжϱê־λ  
}

void EXTI4_IRQHandler(void)
{
	delay_ms(10);//Ïû¶¶
	if(KEY0==0)	 //°´¼üKEY0
	{
//		LED0=!LED0;
//		LED1=!LED1; 
		h_max=h_max-1;
	}		 
	EXTI_ClearITPendingBit(EXTI_Line4);  //Çå³ýLINE4ÉϵÄÖжϱê־λ  
}
void EXIT(void)
{
//	 u8 temp,humi;
  if(temp>=T_max)                    //ζÈãÐÖµ
			{

			BEEP=1;                   //¿ª·äÃùÆ÷
			Motor_ZHENG();
			TIM_SetCompare2(TIM3,90);
			}
	else 
	{
		BEEP=0; 
		Motor_OFF();
	}
	if(humi>=h_max)
	{
		LED1=0;
	}
	else
	{
		LED1=1;
	}
}

void config(void)
{
	 
	  sprintf((char*)T_num,"%d ",T_max);
		sprintf((char*)H_num,"%d ",h_max);
	  OLED_ShowString(60,16,"T:",16,1);
		OLED_ShowString(60,32,"H:",16,1);
	  OLED_ShowString(86,16,T_num,16,1);
		OLED_ShowString(86,32,H_num,16,1);
}
void dht(void)
{
	DHT11_Read_Data(&temp,&humi);
		sprintf((char*)temp_num,"%d ",temp);
		sprintf((char*)humi_num,"%d ",humi);
		delay_ms(50);
		OLED_Refresh();
		OLED_ShowString(0,16,"t:",16,1);
		OLED_ShowString(1,32,"h:",16,1);
    OLED_ShowString(32,16,temp_num,16,1);
		OLED_ShowString(32,32,humi_num,16,1);
}

exti.h

#ifndef __EXTI_H
#define __EXIT_H	 
#include "sys.h"
  	 
void EXTIX_Init(void);//ÍⲿÖжϳõʼ»¯		
void EXIT(void);
#endif

3.LED

led.c

#include "led.h"


void LED_Init(void)
{
 
 GPIO_InitTypeDef  GPIO_InitStructure;
 	
 RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB|RCC_APB2Periph_GPIOE, ENABLE);	 //ʹÄÜPB,PE¶Ë¿ÚʱÖÓ
	
 GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5;				 //LED0-->PB.5 ¶Ë¿ÚÅäÖÃ
 GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP; 		 //ÍÆÍìÊä³ö
 GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;		 //IO¿ÚËÙ¶ÈΪ50MHz
 GPIO_Init(GPIOB, &GPIO_InitStructure);					 //¸ù¾ÝÉ趨²ÎÊý³õʼ»¯GPIOB.5
 GPIO_SetBits(GPIOB,GPIO_Pin_5);						 //PB.5 Êä³ö¸ß

 GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5;	    		 //LED1-->PE.5 ¶Ë¿ÚÅäÖÃ, ÍÆÍìÊä³ö
 GPIO_Init(GPIOE, &GPIO_InitStructure);	  				 //ÍÆÍìÊä³ö £¬IO¿ÚËÙ¶ÈΪ50MHz
 GPIO_SetBits(GPIOE,GPIO_Pin_5); 						 //PE.5 Êä³ö¸ß 
}
 

led.h

#ifndef __LED_H
#define __LED_H	 
#include "sys.h"
 
#define LED0 PBout(5)// PB5
#define LED1 PEout(5)// PE5	

void LED_Init(void);//³õʼ»¯

		 				    
#endif