2021-05-27

最新推荐文章于 2024-05-28 20:49:56 发布
最新推荐文章于 2024-05-28 20:49:56 发布
阅读量577 收藏
点赞数
文章标签： 经验分享
版权声明：本文为博主原创文章，遵循 CC 4.0 BY-SA 版权协议，转载请附上原文出处链接和本声明。
本文链接：https://blog.csdn.net/m0_56229717/article/details/117338594
版权

 

拓扑图

R1

Please press enter to start cmd line!

 

<r1>

May 26 2021 20:04:16-08:00 r1 %%01IFPDT/4/IF_STATE(l)[0]:Interface GigabitEthern

et0/0/1 has turned into UP state.

<r1>

May 26 2021 20:04:20-08:00 r1 %%01IFPDT/4/IF_STATE(l)[1]:Interface GigabitEthern

et0/0/0 has turned into UP state.

<r1>

May 26 2021 20:04:20-08:00 r1 %%01IFNET/4/LINK_STATE(l)[2]:The line protocol IP

on the interface GigabitEthernet0/0/0 has entered the UP state.

<r1>

May 26 2021 20:04:20-08:00 r1 %%01IFPDT/4/IF_STATE(l)[3]:Interface GigabitEthern

et0/0/2 has turned into UP state.

<r1>

May 26 2021 20:04:20-08:00 r1 %%01IFNET/4/LINK_STATE(l)[4]:The line protocol IP

on the interface Tunnel0/0/0 has entered the UP state.

<r1>sys

Enter system view, return user view with Ctrl+Z.

[r1]dhcp enab

[r1]dhcp enable

Info: The operation may take a few seconds. Please wait for a moment.done.

[r1]ip poo

[r1]ip pool q

Info: It's successful to create an IP address pool.

[r1-ip-pool-q]gat

[r1-ip-pool-q]gateway-list 192.168.1.1

[r1-ip-pool-q]natw

[r1-ip-pool-q]net

[r1-ip-pool-q]netw

[r1-ip-pool-q]network 192.168.1.0 ma

[r1-ip-pool-q]network 192.168.1.0 mask 24

[r1-ip-pool-q]dns

[r1-ip-pool-q]dns-list 8.8.8.8

[r1-ip-pool-q]q

[r1]interf

[r1]interface g

[r1]interface GigabitEthernet 0/0/1

[r1-GigabitEthernet0/0/1]ip add

[r1-GigabitEthernet0/0/1]ip address 192.168.1.1 24

May 26 2021 20:08:52-08:00 r1 %%01IFNET/4/LINK_STATE(l)[5]:The line protocol IP

on the interface GigabitEthernet0/0/1 has entered the UP state.

[r1-GigabitEthernet0/0/1]dhc

[r1-GigabitEthernet0/0/1]dhcp se

[r1-GigabitEthernet0/0/1]dhcp select g

[r1-GigabitEthernet0/0/1]dhcp select global

[r1-GigabitEthernet0/0/1]

 

  Please check whether system data has been changed, and save data in time

 

  Configuration console time out, please press any key to log on

 

<r1>

<r1>sys

Enter system view, return user view with Ctrl+Z.

[r1]ip rou

[r1]ip route-s

[r1]ip route-static 0.0.0.0 0 66.1.1.2

[r1]scl 2000

    ^

Error: Unrecognized command found at '^' position.

[r1]q

<r1>acl 2000

    ^

Error: Unrecognized command found at '^' position.

<r1>sys

Enter system view, return user view with Ctrl+Z.

[r1]ac

[r1]acl nu

[r1]acl number 2000

[r1-acl-basic-2000]ru

[r1-acl-basic-2000]rule 0 per

[r1-acl-basic-2000]rule 0 permit sou

[r1-acl-basic-2000]rule 0 permit source 192.168.1.0 0.0.0.255

[r1-acl-basic-2000]q

[r1]interf

[r1]interface g

[r1]interface GigabitEthernet 0/0/1

[r1-GigabitEthernet0/0/1]q

[r1]interf

[r1]interface 0/0/1

              ^

Error: Wrong parameter found at '^' position.

[r1]interface g

[r1]interface GigabitEthernet 0/0/1

[r1-GigabitEthernet0/0/1]ip add

[r1-GigabitEthernet0/0/1]ip address 192.168.1.1 24

Error: The address already exists.

[r1-GigabitEthernet0/0/1]ip address 192.168.1.1 255.255.255.252

[r1-GigabitEthernet0/0/1]nat out

[r1-GigabitEthernet0/0/1]nat outbound 2000

[r1-GigabitEthernet0/0/1]q

[r1]interf

[r1]interface t

[r1]interface Tunnel 0/0/1

[r1-Tunnel0/0/1]

[r1-Tunnel0/0/1]ip add

[r1-Tunnel0/0/1]ip address 100.1.1.1 255.255.255.0

[r1-Tunnel0/0/1]t

[r1-Tunnel0/0/1]tun

[r1-Tunnel0/0/1]tunnel-protocol gr

[r1-Tunnel0/0/1]tunnel-protocol gre p

[r1-Tunnel0/0/1]tunnel-protocol gre p2mp

[r1-Tunnel0/0/1]ospf

[r1-Tunnel0/0/1]ospf net

[r1-Tunnel0/0/1]ospf network-type b

[r1-Tunnel0/0/1]ospf network-type broadcast

[r1-Tunnel0/0/1]ospf dr

[r1-Tunnel0/0/1]ospf dr-priority 225

[r1-Tunnel0/0/1]nh

[r1-Tunnel0/0/1]nhrp en

[r1-Tunnel0/0/1]nhrp entry m

[r1-Tunnel0/0/1]nhrp entry multicast d

[r1-Tunnel0/0/1]nhrp entry multicast dynamic

[r1-Tunnel0/0/1]nh

[r1-Tunnel0/0/1]nhrp n

[r1-Tunnel0/0/1]nhrp network-id 200

[r1-Tunnel0/0/1]nh

[r1-Tunnel0/0/1]nhrp en

[r1-Tunnel0/0/1]nhrp entry 100.1.1.2 46.1.1.1 re

[r1-Tunnel0/0/1]nhrp entry 100.1.1.2 46.1.1.1 register

[r1-Tunnel0/0/1]q

[r1]ospf

[r1-ospf-1]ar

[r1-ospf-1]area 0

[r1-ospf-1-area-0.0.0.0]netw

[r1-ospf-1-area-0.0.0.0]network 10.1.1.0 0.0.0.255

[r1-ospf-1-area-0r2.0.0.0]netw

[r1-ospf-1-area-0.0.0.0]network 100.1.1.0 0.0.0.255

[r1-ospf-1-area-0.0.0.0]

 

  Please check whether system data has been changed, and save data in time

 

  Configuration console time out, please press any key to log on

 

R2

Please press enter to start cmd line!

################################################################################

################################################

<Huawei>

May 26 2021 18:04:13-08:00 Huawei %%01IFPDT/4/IF_STATE(l)[0]:Interface GigabitEt

hernet0/0/0 has turned into UP state.

<Huawei>SYS

Enter system view, return user view with Ctrl+Z.

[Huawei]sysname r2

[r2]ip add

[r2]ip ad

[r2]interf

[r2]interface g

[r2]interface GigabitEthernet 0/0/0

[r2-GigabitEthernet0/0/0]ip add

[r2-GigabitEthernet0/0/0]ip address 26.1.1.1 24

[r2-GigabitEthernet0/0/0]

May 26 2021 18:07:16-08:00 r2 %%01IFNET/4/LINK_STATE(l)[1]:The line protocol IP

on the interface GigabitEthernet0/0/0 has entered the UP state.

[r2-GigabitEthernet0/0/0]q

[r2]interf

[r2]interface l

[r2]interface LoopBack 0

[r2-LoopBack0]ip add

[r2-LoopBack0]ip address 2.2.2.2 24

[r2-LoopBack0]

 

  Please check whether system data has been changed, and save data in time

 

  Configuration console time out, please press any key to log on

 

<r2>

<r2>sys

Enter system view, return user view with Ctrl+Z.

[r2]tun

[r2]tunnel 0/0/0

           ^

Error: Unrecognized command found at '^' position.

[r2]interf

[r2]interface tu

[r2]interface Tunnel 0/0/0

[r2-Tunnel0/0/0]ip add

[r2-Tunnel0/0/0]ip address 10.1.1.2

                                    ^

Error:Incomplete command found at '^' position.

[r2-Tunnel0/0/0]ip address 10.1.1.2 24

[r2-Tunnel0/0/0]nh

[r2-Tunnel0/0/0]sour

[r2-Tunnel0/0/0]so

[r2-Tunnel0/0/0]?

Tunnel0/0/0 interface view commands:

  arp-ping           ARP-ping

  backup             Backup  information

  bandwidth          Specify mib-referenced bandwidth of the interface

  clear              <Group> clear command group

  ddns               DDNS

  description        Specify interface description

  dialer             Dialer

  discard            Discard packets

  display            Display information

  enable             Enable function

  hotstandby-switch  Hot-Standby LSP manual switch

  icmp               Specify ICMP configuration information

  igmp               Specify parameters for IGMP

  ip                 <Group> ip command group

  ipv6               IPv6 configuration commands

  isis               Configure interface parameters for ISIS

  mirror             Specify Mirror feature

  mpls               Multiprotocol Label Switching(MPLS) status and             

                     configuration information

  mtrace             Trace route to multicast source

  mtu                Specify Maximum Transmission Unit(MTU) of the interface

  multicast          Multicast information

  nat                Specify NAT(Network Address Translation) configuration     

                     information

 

[r2-Tunnel0/0/0]ys

                ^

Error: Unrecognized command found at '^' position.

[r2-Tunnel0/0/0]tun

[r2-Tunnel0/0/0]tunnel-protocol gre mp

[r2-Tunnel0/0/0]tunnel-protocol gre m

[r2-Tunnel0/0/0]tunnel-protocol gre m2

[r2-Tunnel0/0/0]tunnel-protocol gre p2

[r2-Tunnel0/0/0]tunnel-protocol gre p2mp

[r2-Tunnel0/0/0]sou

[r2-Tunnel0/0/0]source g

[r2-Tunnel0/0/0]source GigabitEthernet 0/0/0

May 26 2021 18:22:41-08:00 r2 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP

on the interface Tunnel0/0/0 has entered the UP state.

[r2-Tunnel0/0/0]

[r2-Tunnel0/0/0]hn

[r2-Tunnel0/0/0]nr

[r2-Tunnel0/0/0]nh

[r2-Tunnel0/0/0]nhrp en

[r2-Tunnel0/0/0]nhrp entry 10.1.1.1 16.1.1.1

[r2-Tunnel0/0/0]q

[r2]ip rou

[r2]ip route-s

[r2]ip route-static 0.0.0.0 0 26.1.1.2

[r2]ospf

[r2-ospf-1]are

               ^

Error:Incomplete command found at '^' position.

[r2-ospf-1]are

[r2-ospf-1]area 0

[r2-ospf-1-area-0.0.0.0]netw

[r2-ospf-1-area-0.0.0.0]network 26.0.0.0 0.255.255.255

[r2-ospf-1-area-0.0.0.0]nerw

[r2-ospf-1-area-0.0.0.0]netw

[r2-ospf-1-area-0.0.0.0]network 10.0.0.0 0.255.255.255

[r2-ospf-1-area-0.0.0.0]

May 26 2021 18:35:12-08:00 r2 %%01OSPF/4/NBR_CHANGE_E(l)[1]:Neighbor changes eve

nt: neighbor status changed. (ProcessId=256, NeighborAddress=2.1.1.26, NeighborE

vent=HelloReceived, NeighborPreviousState=Down, NeighborCurrentState=Init)

[r2-ospf-1-area-0.0.0.0]

May 26 2021 18:35:14-08:00 r2 %%01OSPF/4/NBR_CHANGE_E(l)[2]:Neighbor changes eve

nt: neighbor status changed. (ProcessId=256, NeighborAddress=2.1.1.26, NeighborE

vent=2WayReceived, NeighborPreviousState=Init, NeighborCurrentState=ExStart)

[r2-ospf-1-area-0.0.0.0]

May 26 2021 18:35:14-08:00 r2 %%01OSPF/4/NBR_CHANGE_E(l)[3]:Neighbor changes eve

nt: neighbor status changed. (ProcessId=256, NeighborAddress=2.1.1.26, NeighborE

vent=NegotiationDone, NeighborPreviousState=ExStart, NeighborCurrentState=Exchan

ge)

[r2-ospf-1-area-0.0.0.0]

May 26 2021 18:35:14-08:00 r2 %%01OSPF/4/NBR_CHANGE_E(l)[4]:Neighbor changes eve

nt: neighbor status changed. (ProcessId=256, NeighborAddress=2.1.1.26, NeighborE

vent=ExchangeDone, NeighborPreviousState=Exchange, NeighborCurrentState=Loading)

 

[r2-ospf-1-area-0.0.0.0]

May 26 2021 18:35:14-08:00 r2 %%01OSPF/4/NBR_CHANGE_E(l)[5]:Neighbor changes eve

nt: neighbor status changed. (ProcessId=256, NeighborAddress=2.1.1.26, NeighborE

vent=LoadingDone, NeighborPreviousState=Loading, NeighborCurrentState=Full)

[r2-ospf-1-area-0.0.0.0]q

[r2-ospf-1]q

[r2]q

<r2>sa

<r2>save

  The current configuration will be written to the device.

  Are you sure to continue? (y/n)[n]:y

  It will take several minutes to save configuration file, please wait........

  Configuration file had been saved successfully

  Note: The configuration file will take effect after being activated

<r2>

 

  Please check whether system data has been changed, and save data in time

 

  Configuration console time out, please press any key to log on

 

<r2>

<r2>sys

Enter system view, return user view with Ctrl+Z.

[r2]dhcp

         ^

Error:Incomplete command found at '^' position.

[r2]se

[r2]set

        ^

Error:Incomplete command found at '^' position.

[r2]

[r2]dhcp en

[r2]dhcp enable

Info: The operation may take a few seconds. Please wait for a moment.done.

[r2]ip ppol

[r2]ip pool a

Info: It's successful to create an IP address pool.

[r2-ip-pool-a]gat

[r2-ip-pool-a]gateway-list 192.168.2.1

[r2-ip-pool-a]netw

[r2-ip-pool-a]network 192.168.2.0 ma

[r2-ip-pool-a]network 192.168.2.0 mask 24

[r2-ip-pool-a]dns

[r2-ip-pool-a]dns-list 8.8.8.8

[r2-ip-pool-a]q

[r2]interf

[r2]interface g

[r2]interface GigabitEthernet 0/0/1

[r2-GigabitEthernet0/0/1]ip add

[r2-GigabitEthernet0/0/1]ip address 192.168.2.1 24

May 26 2021 19:29:22-08:00 r2 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP

on the interface GigabitEthernet0/0/1 has entered the UP state.

[r2-GigabitEthernet0/0/1]dh

[r2-GigabitEthernet0/0/1]dhcp se

[r2-GigabitEthernet0/0/1]dhcp select g

[r2-GigabitEthernet0/0/1]dhcp select global

[r2-GigabitEthernet0/0/1]

 

  Please check whether system data has been changed, and save data in time

 

  Configuration console time out, please press any key to log on

 

<r2>

<r2>sys

Enter system view, return user view with Ctrl+Z.

[r2]acl n

[r2]acl nu

[r2]acl number 2000

[r2-acl-basic-2000]ru

[r2-acl-basic-2000]rule per

[r2-acl-basic-2000]rule permit sou

[r2-acl-basic-2000]rule permit source 192.168.2.0 0.0.0.255\

                                                  ^

Error: Wrong parameter found at '^' position.

[r2-acl-basic-2000]rule permit source 192.168.2.0 0.0.0.255

[r2-acl-basic-2000]q

[r2]interf

[r2]interface g

[r2]interface GigabitEthernet 0/0/1

[r2-GigabitEthernet0/0/1]nat out

[r2-GigabitEthernet0/0/1]nat outbound 2000

[r2-GigabitEthernet0/0/1]q

[r2]ospf

[r2-ospf-1]are

[r2-ospf-1]area 0

[r2-ospf-1-area-0.0.0.0]net

[r2-ospf-1-area-0.0.0.0]network

 

  Please check whether system data has been changed, and save data in time

 

  Configuration console time out, please press any key to log on

 

R5

Please press enter to start cmd line!

################################################################################

##############################################

<Huawei>

May 26 2021 18:04:14-08:00 Huawei %%01IFPDT/4/IF_STATE(l)[0]:Interface GigabitEt

hernet0/0/0 has turned into UP state.

<Huawei>sys

Enter system view, return user view with Ctrl+Z.

[Huawei]sysname r4

[r4]interf

[r4]interface g

[r4]interface GigabitEthernet 0/0/0

[r4-GigabitEthernet0/0/0]ip add

[r4-GigabitEthernet0/0/0]ip address 46.1.1.1 24

May 26 2021 18:09:19-08:00 r4 %%01IFNET/4/LINK_STATE(l)[1]:The line protocol IP

on the interface GigabitEthernet0/0/0 has entered the UP state.

[r4-GigabitEthernet0/0/0]q

[r4]interf

[r4]interface l

[r4]interface LoopBack 0

[r4-LoopBack0]ip add

[r4-LoopBack0]ip address 4.4.4.4 24

[r4-LoopBack0]

 

  Please check whether system data has been changed, and save data in time

 

  Configuration console time out, please press any key to log on

 

<r4>sys

Enter system view, return user view with Ctrl+Z.

[r4]ip rou

[r4]ip route-s

[r4]ip route-static 0.0.0.0 0 46.1.1.2

[r4]

 

  Please check whether system data has been changed, and save data in time

 

  Configuration console time out, please press any key to log on

 

<r4>

<r4>sa

<r4>save

  The current configuration will be written to the device.

  Are you sure to continue? (y/n)[n]:y

  It will take several minutes to save configuration file, please wait.......

  Configuration file had been saved successfully

  Note: The configuration file will take effect after being activated

<r4>

 

  Please check whether system data has been changed, and save data in time

 

  Configuration console time out, please press any key to log on

 

<r4>

<r4>sys

Enter system view, return user view with Ctrl+Z.

[r4]dhcp

[r4]dhcp en

[r4]dhcp enable

Info: The operation may take a few seconds. Please wait for a moment.done.

[r4]ip po

[r4]ip poo

[r4]ip pool a

Info: It's successful to create an IP address pool.

[r4-ip-pool-a]gatw

[r4-ip-pool-a]gate

[r4-ip-pool-a]gateway-list 192.168.4.1

[r4-ip-pool-a]nwtw

[r4-ip-pool-a]netw

[r4-ip-pool-a]network 192.168.4.0 ma

[r4-ip-pool-a]network 192.168.4.0 mask 24

[r4-ip-pool-a]dns

[r4-ip-pool-a]dns-list 8.8.8.8

[r4-ip-pool-a]q

[r4]interf

[r4]interface g

[r4]interface GigabitEthernet 0/0/1

[r4-GigabitEthernet0/0/1]ip add

[r4-GigabitEthernet0/0/1]ip address 192.168.4.1 24

May 26 2021 19:33:49-08:00 r4 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP

on the interface GigabitEthernet0/0/1 has entered the UP state.

[r4-GigabitEthernet0/0/1]dhcp

[r4-GigabitEthernet0/0/1]dhcp se

[r4-GigabitEthernet0/0/1]dhcp select g

[r4-GigabitEthernet0/0/1]dhcp select global

[r4-GigabitEthernet0/0/1]

 

  Please check whether system data has been changed, and save data in time

 

  Configuration console time out, please press any key to log on

 

<r4>sys

Enter system view, return user view with Ctrl+Z.

[r4]acl nu

[r4]acl number 2000

[r4-acl-basic-2000]ru

[r4-acl-basic-2000]rule per

[r4-acl-basic-2000]rule  0 per

[r4-acl-basic-2000]rule  0 permit sou

[r4-acl-basic-2000]rule  0 permit source 192.168.4.0

                                                     ^

Error:Incomplete command found at '^' position.

[r4-acl-basic-2000]rule 0 permit source 192.168.4.0 0.0.0.255

[r4-acl-basic-2000]q

[r4]interf

[r4]interface g

[r4]interface GigabitEthernet 0/0/0

[r4-GigabitEthernet0/0/0]nat

[r4-GigabitEthernet0/0/0]nat ou

[r4-GigabitEthernet0/0/0]nat outbound 200

                                      ^

Error: Wrong parameter found at '^' position.

[r4-GigabitEthernet0/0/0]nat outbound 2000

[r4-GigabitEthernet0/0/0]q\

                         ^

Error: Unrecognized command found at '^' position.

[r4-GigabitEthernet0/0/0]q

[r4]interf

[r4]interface t

[r4]interface Tunnel 0/0/1

[r4-Tunnel0/0/1]ip add

[r4-Tunnel0/0/1]ip address 100.1.1.2 255.255.255.0

[r4-Tunnel0/0/1]t

[r4-Tunnel0/0/1]tu

[r4-Tunnel0/0/1]tunnel-protocol gr

[r4-Tunnel0/0/1]tunnel-protocol gre p

[r4-Tunnel0/0/1]tunnel-protocol gre p2mp

[r4-Tunnel0/0/1]osp

[r4-Tunnel0/0/1]ospf ne

[r4-Tunnel0/0/1]ospf network-type b

[r4-Tunnel0/0/1]ospf network-type broadcast

[r4-Tunnel0/0/1]nh

[r4-Tunnel0/0/1]nhrp th

[r4-Tunnel0/0/1]nhrpen

[r4-Tunnel0/0/1]nhrp en

[r4-Tunnel0/0/1]nhrp entry m

[r4-Tunnel0/0/1]nhrp entry multicast d

[r4-Tunnel0/0/1]nhrp entry multicast dynamic

[r4-Tunnel0/0/1]nh

[r4-Tunnel0/0/1]nhrp net

[r4-Tunnel0/0/1]nhrp network-id 2000

[r4-Tunnel0/0/1]nhrp network-id 200

[r4-Tunnel0/0/1]q

[r4]sopf

[r4]sopf

    ^

Error: Unrecognized command found at '^' position.

[r4]ar

[r4]are

[r4]are0

    ^

Error: Unrecognized command found at '^' position.

[r4]are

[r4]osp

[r4]ospf

[r4-ospf-1]are

[r4-ospf-1]area 0

[r4-ospf-1-area-0.0.0.0]netw

[r4-ospf-1-area-0.0.0.0]network 100.1.1.0 0.0.0.255

[r4-ospf-1-area-0.0.0.0]

 

  Please check whether system data has been changed, and save data in time

 

  Confir6guration console time out, please press any key to log on

R6

 

Please press enter to start cmd line!

################################################################################

############

<r6>

May 26 2021 20:04:19-08:00 r6 %%01DEV/4/ENTUP(l)[0]:1GEC board[3] register succe

ss.

<r6>

May 26 2021 20:04:19-08:00 r6 %%01IFNET/4/BOARD_ENABLE(l)[1]:Board 3 has been av

ailable.

<r6>

May 26 2021 20:04:19-08:00 r6 %%01IFNET/4/IF_ENABLE(l)[2]:Interface GigabitEther

net3/0/0 has been available.

<r6>

May 26 2021 20:04:20-08:00 r6 %%01DEV/4/ENTUP(l)[3]:1GEC board[4] register succe

ss.

<r6>

May 26 2021 20:04:20-08:00 r6 %%01IFNET/4/BOARD_ENABLE(l)[4]:Board 4 has been av

ailable.

<r6>

May 26 2021 20:04:20-08:00 r6 %%01IFNET/4/IF_ENABLE(l)[5]:Interface GigabitEther

net4/0/0 has been available.

<r6>

May 26 2021 20:04:21-08:00 r6 %%01IFPDT/4/IF_STATE(l)[6]:Interface GigabitEthern

et0/0/0 has turned into UP state.

<r6>

May 26 2021 20:04:21-08:00 r6 %%01IFNET/4/LINK_STATE(l)[7]:The line protocol IP

on the interface GigabitEthernet0/0/0 has entered the UP state.

<r6>

May 26 2021 20:04:21-08:00 r6 %%01IFPDT/4/IF_STATE(l)[8]:Interface GigabitEthern

et0/0/1 has turned into UP state.

<r6>

May 26 2021 20:04:21-08:00 r6 %%01IFNET/4/LINK_STATE(l)[9]:The line protocol IP

on the interface GigabitEthernet0/0/1 has entered the UP state.

<r6>

May 26 2021 20:04:21-08:00 r6 %%01IFPDT/4/IF_STATE(l)[10]:Interface GigabitEther

net0/0/2 has turned into UP state.

<r6>

May 26 2021 20:04:21-08:00 r6 %%01IFNET/4/LINK_STATE(l)[11]:The line protocol IP

 on the interface GigabitEthernet0/0/2 has entered the UP state.

<r6>

May 26 2021 20:04:21-08:00 r6 %%01IFPDT/4/IF_STATE(l)[12]:Interface GigabitEther

net2/0/0 has turned into UP state.

<r6>

May 26 2021 20:04:21-08:00 r6 %%01IFPDT/4/IF_STATE(l)[13]:Interface GigabitEther

net3/0/0 has turned into UP state.

<r6>

May 26 2021 20:04:21-08:00 r6 %%01IFNET/4/LINK_STATE(l)[14]:The line protocol IP

 on the interface GigabitEthernet3/0/0 has entered the UP state.

<r6>

May 26 2021 20:04:22-08:00 r6 %%01IFPDT/4/IF_STATE(l)[15]:Interface GigabitEther

net4/0/0 has turned into UP state.

<r6>

May 26 2021 20:04:22-08:00 r6 %%01IFNET/4/LINK_STATE(l)[16]:The line protocol IP

 on the interface GigabitEthernet4/0/0 has entered the UP state.

<r6>

May 26 2021 20:04:31-08:00 r6 %%01OSPF/4/NBR_CHANGE_E(l)[17]:Neighbor changes ev

ent: neighbor status changed. (ProcessId=256, NeighborAddress=1.1.1.26, Neighbor

Event=HelloReceived, NeighborPreviousState=Down, NeighborCurrentState=Init)

<r6>

May 26 2021 20:04:31-08:00 r6 %%01OSPF/4/NBR_CHANGE_E(l)[18]:Neighbor changes ev

ent: neighbor status changed. (ProcessId=256, NeighborAddress=1.1.1.26, Neighbor

Event=2WayReceived, NeighborPreviousState=Init, NeighborCurrentState=2Way)

<r6>

May 26 2021 20:04:58-08:00 r6 %%01OSPF/4/NBR_CHANGE_E(l)[19]:Neighbor changes ev

ent: neighbor status changed. (ProcessId=256, NeighborAddress=1.1.1.26, Neighbor

Event=AdjOk?, NeighborPreviousState=2Way, NeighborCurrentState=ExStart)

<r6>

May 26 2021 20:05:01-08:00 r6 %%01OSPF/4/NBR_CHANGE_E(l)[20]:Neighbor changes ev

ent: neighbor status changed. (ProcessId=256, NeighborAddress=1.1.1.26, Neighbor

Event=NegotiationDone, NeighborPreviousState=ExStart, NeighborCurrentState=Excha

nge)

<r6>

May 26 2021 20:05:01-08:00 r6 %%01OSPF/4/NBR_CHANGE_E(l)[21]:Neighbor changes ev

ent: neighbor status changed. (ProcessId=256, NeighborAddress=1.1.1.26, Neighbor

Event=ExchangeDone, NeighborPreviousState=Exchange, NeighborCurrentState=Loading

)

<r6>

May 26 2021 20:05:01-08:00 r6 %%01OSPF/4/NBR_CHANGE_E(l)[22]:Neighbor changes ev

ent: neighbor status changed. (ProcessId=256, NeighborAddress=1.1.1.26, Neighbor

Event=LoadingDone, NeighborPreviousState=Loading, NeighborCurrentState=Full)

<r6>

 

  Please check whether system data has been changed, and save data in time

 

  Configuration console time out, please press any key to log on

 

<r6>

<r6>

<r6>sys

Enter system view, return user view with Ctrl+Z.

[r6]interf

[r6]interface g

[r6]interface GigabitEthernet 0/0/0

[r6-GigabitEthernet0/0/0]ip add

[r6-GigabitEthernet0/0/0]ip address 16.1.1.2 255.255.255.252

[r6-GigabitEthernet0/0/0]q

[r6]interf

[r6]interface g

[r6]interface GigabitEthernet 2/0/0

[r6-GigabitEthernet2/0/0]ip add

[r6-GigabitEthernet2/0/0]ip address 66.1.1.2 255.255.255.252

[r6-GigabitEthernet2/0/0]

May 26 2021 20:43:27-08:00 r6 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP

on the interface GigabitEthernet2/0/0 has entered the UP state.

[r6-GigabitEthernet2/0/0]q

[r6]inter

[r6]interface g

[r6]interface GigabitEthernet 0/0/2

[r6-GigabitEthernet0/0/2]ip add

[r6-GigabitEthernet0/0/2]ip address 26.1.1.2 255.255.255.252

May 26 2021 20:44:03-08:00 r6 %%01OSPF/3/NBR_CHG_DOWN(l)[1]:Neighbor event:neigh

bor state changed to Down. (ProcessId=256, NeighborAddress=1.1.1.26, NeighborEve

nt=KillNbr, NeighborPreviousState=Full, NeighborCurrentState=Down)

[r6-GigabitEthernet0/0/2]

May 26 2021 20:44:03-08:00 r6 %%01OSPF/3/NBR_DOWN_REASON(l)[2]:Neighbor state le

aves full or changed to Down. (ProcessId=256, NeighborRouterId=1.1.1.26, Neighbo

rAreaId=0, NeighborInterface=GigabitEthernet0/0/2,NeighborDownImmediate reason=N

eighbor Down Due to Kill Neighbor, NeighborDownPrimeReason=Logical Interface Sta

te Change, NeighborChangeTime=2021-05-26 20:44:03-08:00)

[r6-GigabitEthernet0/0/2]q

[r6]interf

[r6]interface g

[r6]interface GigabitEthernet 0/0/1

[r6-GigabitEthernet0/0/1]ip add

[r6-GigabitEthernet0/0/1]ip address 36.1.1.2 255.255.255.252

[r6-GigabitEthernet0/0/1]q

[r6]interf

[r6]interface g

[r6]interface GigabitEthernet 4/0/0

[r6-GigabitEthernet4/0/0]ip add

[r6-GigabitEthernet4/0/0]ip address 46.1.1.2 255.255.255.252

[r6-GigabitEthernet4/0/0]q

[r6]interf

[r6]interface G

[r6]interface GigabitEthernet 3/0/0

[r6-GigabitEthernet3/0/0]OP ASDD

[r6-GigabitEthernet3/0/0]ip aa

[r6-GigabitEthernet3/0/0]ip ad

[r6-GigabitEthernet3/0/0]ip address 56.1.1.2 255.255.255.252

[r6-GigabitEthernet3/0/0]

 

  Please check whether system data has been changed, and save data in time

 

  Configuration console time out, please press any key to log on

 

 

 

 

m0_56229717
关注
  • 0
    点赞
  • 踩
  • 0
    收藏
    觉得还不错? 一键收藏
  • 0
    评论
2021-05-27function.py
05-27
匹配文件的配置文件
汽车之家车型最新数据2021-05-27上传
05-27
标题中的“汽车之家车型最新数据2021-05-27上传”表明这是一个关于汽车之家网站在2021年5月27日更新的车型数据集。汽车之家是中国知名的汽车信息和服务平台，其车型数据通常包含了丰富的汽车行业信息，如车型参数、...
关于华为ensp一些报错处理分享及基础命令
热门推荐
所爱的博客
08-31 5万+
1.Error: Unrecognized command found at '^' position. 这里会发现在输入sys按TAb键时不会自动补全，那我们这是就应该反应过来，肯定是哪里有问题了，比如输入system-view时报错，你注意看是<>还是[]了吗，[]时输入system-view是错误的，也不会自动补全，解决方法是ctrl+z，其实他下面也有提示 后来我发现是视图的原因 eNSP有种视图模式 : 用户视图 | 系统视图 | 接口视图 ...
Error:Incomplete command found at ‘^‘ position.
一起coding，一起嗨。
03-30 1万+
华为eNSP,启动后输入命令sys,报错Error:Incomplete command found at '^' position.如何处理？
华为、华三、思科、锐捷交换机路由器设备命令行常见错误信息
最新发布
小木的博客
05-28 866
使用CLI命令行界面，如果输入错误，系统将会向用户报告错误信息。 知己知彼，方能百战不殆。下面是小木为大家收集整理的几大厂商常见的命令行错误提示。
华为设备 命令行的错误提示
weixin_48776593的博客
01-30 3024
(error:误差,)（found:找到,）（position:定位,（command:控制,）（wrong:不合适,（parameter:范围,
2021-05-20
m0_56229717的博客
05-20 887
题目要求 拓扑图 R1 on the interface GigabitEthernet0/0/1 has entered the UP state. [r1-GigabitEthernet0/0/1] Please check whether system data has been changed, and save data in time Configuration console time...
关于计算机网络实验心得体会以及两种错误情况
qq_61194674的博客
10-21 4646
一开始就是在反复地试错当中，因为对每行代码不够理解导致配置总是出错误，现在已经熟知了自己的两种错误。
2021-05-27 查询客户邮箱.py
05-27
python链接数据库，抓取数据及处理后存入excel或MySQL的脚本（20)
tampermonkey-backup-chrome-2021-11-27T01-27-17-766Z.zip
11-27
配置过的油猴插件
优质资料（2021-2022年收藏）数控车工技师理论知识试卷05.doc
10-11
这是一份2021-2022年度的浙江省职业技能鉴定统一试卷，针对数控车工技师的理论知识考核。考试包含两大部分：理论知识（占比80%）和职业道德（占比20%），总时长120分钟。考生需要在指定位置填写个人信息，并严格按照...
UL 486A-486B：2021-05 Wire Connectors - 完整英文版（89页）.pdf
09-02
《UL 486A-486B：2021-05 Wire Connectors》标准详细解读 UL 486A-486B是美国保险商实验室（Underwriters Laboratories）发布的一项关于电线连接器的安全标准，旨在确保电线连接器在各种应用中的性能和安全性。该...
Analytics-90Day-2021-12-18-080027.0003.ips.ca.synced
12-18
Analytics-90Day-2021-12-18-080027.0003.ips.ca.synced
Pipeline-Trigger-2021-03-03T18-38-31.177Z：为工具链创建：https：//dev.console.test.cloud.ibm.comdevopstoolchainsbb27f7cf-f05e-4702-9110-15722f3bb627？env_id = ibm：ys1：us-south
03-04
标题中的“Pipeline-Trigger-2021-03-03T18-38-31.177Z”很可能是一个自动化构建或持续集成（CI/CD）过程的标识符，其中包含了时间戳，表明这个过程是在2021年3月3日的18时38分31秒触发的。"为工具链创建"说明这可能...
精品（2021-2022年）资料质量管理体系考试题转载.doc
09-27
46. GB/Z19027-05：提供了选择和应用统计技术的指南。 47. 持续改进活动：涵盖产品、过程和质量管理体系。 48. “过程的监视和测量”：适用于产品实现过程，但标准中的表述可能有误。 49. GB/T2828.1-03转移规则...
leetcode跳跃-LeetCodeNotes:leetcode笔记
06-30
leetcode 跳跃 LeetCodeNodes # 创建新项目, ...2021-05-27 100% 2021-05-28 100% 2021-05-29 100% 2021-05-30 100% 2021-05-31 100% 2021-06-01 100% 2021-06-02 100% 2021-06-03 100% 2021-06-04
作业11.18
zhuqifan0412的博客
11-18 361
作业
配置H3C交换机
汤庆
12-30 7666
一、初次配置H3C交换机过程简备（采用超级终端） 超级终端路径有两个：C:\WINDOWS\system32和C:\Program Files\Windows NT下，将两个文件拷到这里就可；只要执行hypertrm.exe文件即可，前提得有hypertrm.dll文件；菜单快捷键则可将文件复制到“C:\Documents and Settings\Administrator\「开始」菜单\程序...
2021-06-09
m0_56229717的博客
06-09 493
R1 The device is running! <Huawei>sys Enter system view, return user view with Ctrl+Z. [Huawei]sysname r1 [r1]interf [r1]interface g [r1]interface GigabitEthernet 0/0/0 [r1-GigabitEthernet0/0/0]ip add 12.1.1.1 24 Jun 9 2021 18:1...
{[{"companyId":100,"companyTicketIds":"230,233,237","addTime":"2021-04-15 10:43:57","name":"100等级全部场所","extraTicketId":0,"editTime":"2023-05-24 13:40:03","id":45,"nightPeriod":"100","goldPeriod":"1000","status":0},{"companyId":100,"companyTicketIds":"230,233,237","addTime":"2022-05-06 13:25:51","name":"208等级全部场所","extraTicketId":0,"editTime":"2022-09-21 15:27:41","id":50,"nightPeriod":"208","goldPeriod":"1200","status":0},{"companyId":100,"companyTicketIds":"230,233,237","addTime":"2022-05-06 13:26:29","name":"203等级部分分成","extraTicketId":0,"editTime":"2022-09-21 15:27:45","id":51,"nightPeriod":"203","goldPeriod":"1100","status":0},{"companyId":100,"companyTicketIds":"327","addTime":"2023-05-06 13:55:26","name":"300登记","extraTicketId":0,"editTime":"2023-05-06 13:57:23","id":61,"nightPeriod":"100","goldPeriod":"1000","status":0}]}这样的json格式哪里有问题
06-06
"addTime": "2021-04-15 10:43:57", "name": "100等级全部场所", "extraTicketId": 0, "editTime": "2023-05-24 13:40:03", "id": 45, "nightPeriod": "100", "goldPeriod": "1000", "status": 0 }, { ...
评论
添加红包

请填写红包祝福语或标题

个

红包个数最小为10个

元

红包金额最低5元

当前余额3.43元 前往充值 >
需支付：10.00元
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付元
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明：

1.余额是钱包充值的虚拟货币，按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载，可以购买VIP、付费专栏及课程。

余额充值