Phantom S710系列相机配置

最新推荐文章于 2024-07-25 17:25:26 发布

Hello-FPGA

最新推荐文章于 2024-07-25 17:25:26 发布

阅读量458

点赞数 3

文章标签：数码相机

本文链接：https://blog.csdn.net/old_stone/article/details/136845988

版权

Phantom S710系列相机配置

S710系列相机配置

2.4 配置示例 BANK A 4ports 7

图 1‑1 芬腾S710相机 4

图 1‑2 S710规格 5

S710系列相机配置

S710相机说明

Phantom S710是一款用于科研的超高速CXP相机。

1280*800 配置下高达7275 帧每秒
4个CXP 6.25端口，每个端口4个PORT，共16个CXP接口

图 1‑1 芬腾S710相机

表格描述已自动生成

图 1‑2 S710规格

配置说明

BANK说明

相机分为4个BANK A,B,C,D。每个BANK有4个CXP Ports。相机可以配置为1 bank of 4 CXP ports, 2 banks of 4 CXP ports, or 4 banks of 4 CXP ports.

In these multi-bank modes, the S710 will be discovered as 2 or 4 separate cameras, but any action done over one bank applies to all connected banks.

在多个BANK模式下，S710会被标准采集卡识别为2个或者4个独立的相机，在1个BANK完成的相机配置会被自动被配置到其它BANK。也就是说采集卡端需要对2或者4个相机的数据进行拼接，完成图像的重新排列。

BANK 配置

重点注意如果是多个BANK配置，对应高度寄存器设置要除以BANK数量。

‘Banks_A’ – 1 Bank mode This configuration allows for a full frame (1280x800) to be streamed over a single bank of 4 CXP ports.

If a maximum bandwidth of ~2Gbps is acceptable, simply connect all 4 ports from Bank A to a 4 port framegrabber card. Change the ‘Banks’ register under ‘CXP’ to ‘Banks_A’ and begin streaming.

‘Banks_AB’ – 2 Bank Mode

This configuration allows for a full frame to be split in half with one section being streamed over Bank A and the other over Bank B. It is important to remember that the ‘Height’ register details the number of lines to be streamed across one of the banks. For example, if a 1280x800 image is required, the ‘Width’ and ‘Height’ registers should be set to ‘1280’ and ‘400’ respectively.

If a maximum bandwidth of ~4Gbps is acceptable, simply connect 4 ports from Bank A to a 4 port framegrabber card and connect 4 ports from Bank B to another 4 port framegrabber card. Change the ‘Banks’ register under ‘CXP’ to ‘Banks_AB’ and begin streaming.

‘Banks_ABCD’ – 4 Bank Mode This configuration allows for a full frame to be split into quarters with each separate sections being streamed over Banks A, B, C and D.

It is important to remember that the ‘Height’ register details the number of lines to be streamed across one of the banks. For example, if a 1280x800 image is required, the ‘Width’ and ‘Height’ registers should be set to ‘1280’ and ‘200’ respectively.

For a maximum bandwidth, simply connect each of the S710 4 port banks to separate 4 Quad or 2 Octo port framegrabber cards. Change the ‘Banks’ register under ‘CXP’ to ‘Banks_ABCD’ and begin streaming.

像素重新排列

S710 sensor 读出不是常规格式，而是从中间行到两端的读出方式。

Each read contains 4 rows of the horizontal resolution length, with 2 rows above the center of the image and 2 rows below the center. Every subsequent packet contains 4 additional rows, with 2 rows above/2 rows below the preceding packet. Depending on the Banks mode configured, these 4 row packets will be distributed, round-robin, to the selected banks.

图形用户界面, 应用程序中度可信度描述已自动生成