NandFlash的分区实现
提到分区就需要知道MBR,了解分区表。
什么是MBR
硬盘的0柱面、0磁头、1扇区称为主引导扇区,NANDFLASH由BLOCK和Sector组成,所以NANDFLASH的第0 BLOCK,第1 Sector为主引导扇区,FDISK程序写到该扇区的内容称为主引导记录(MBR)。该记录占用512个字节,它用于硬盘启动时将系统控制权交给用户指定的,并在分区表中登记了的某个操作系统区。
MBR的组成
一个扇区的硬盘主引导记录MBR由如图6-15所示的4个部分组成。
- 主引导程序(偏移地址0000H—0088H),它负责从活动分区中装载,并运行系统引导程序。
- 出错信息数据区,偏移地址0089H--00E1H为出错信息,00E2H--01BDH全为0字节。
- 分区表(DPT,Disk Partition Table)含4个分区项,偏移地址01BEH--01FDH,每个分区表项长16个字节,共64字节为分区项1、分区项2、分区项3、分区项4。
- 结束标志字,偏移地址01FE--01FF的2个字节值为结束标志55AA,如果该标志错误系统就不能启动。
0000-0088 Master Boot Record
主引导程序
主引导
程序
0089-01BD 出错信息数据区 数据区 01BE-01CD
分区项1(16字节)
分区表
01CE-01DD
分区项2(16字节)
… 01DE-01ED
分区项3(16字节)
… 01EE-01FD
分区项4(16字节)
… 01FE
55
结束标志 01FF
AA
… 图6-15 MBR的组成结构图
MBR中的分区信息结构
占用512个字节的MBR中,偏移地址01BEH--01FDH的64个字节,为4个分区项内容(分区信息表)。它是由磁盘介质类型及用户在使用 FDISK定义分区说确定的。在实际应用中,FDISK对一个磁盘划分的主分区可少于4个,但最多不超过4个。每个分区表的项目是16个字节,其内容含义 如表6-19所示。
表6-19 分区项表(16字节)内容及含义
存贮字节位 内容及含义 第1字节 引导标志。若值为80H表示活动分区,若值为00H表示非活动分区。 第2、3、4字节 本分区的起始磁头号、扇区号、柱面号。其中:
磁头号——第2字节;
扇区号——第3字节的低6位;
柱面号——为第3字节高2位+第4字节8位。
第5字节 分区类型符:
00H——表示该分区未用(即没有指定);
06H——FAT16基本分区;
0BH——FAT32基本分区;
05H——扩展分区;
07H——NTFS分区;
0FH——(LBA模式)扩展分区(83H为Linux分区等)。
第6、7、8字节 本分区的结束磁头号、扇区号、柱面号,其中:
磁头号——第6字节;
扇区号——第7字节的低6位;
柱面号——第7字节的高2位+第8字节。
第9、10、11、12字节 本分区之前已用了的扇区数 第13、14、15、16字节 本分区的总扇区数
EBOOT中对NAND分区主要代码,eboot目录下的fmd.cpp文件,与NAND驱动基本相同,所以,要对NAND进行分区,就得对NAND驱动非常熟悉。透彻了解。然后就是E:/WINCE500/PUBLIC/COMMON/OAK/DRIVERS/ETHDBG/BOOTPART/bootpart.cpp文件了。该文件主要通过调用NANDFLASH的读写操作来写入MBR,也是今天主要的分析对象。
主要函数。
Code Snippet
- /* BP_OpenPartition
- *
- * Opens/creates a partition depending on the creation flags. If it is opening
- * and the partition has already been opened, then it returns a handle to the
- * opened partition. Otherwise, it loads the state information of that partition
- * into memory and returns a handle.
- *
- * ENTRY
- * dwStartSector - Logical sector to start the partition. NEXT_FREE_LOC if none
- * specified. Ignored if opening existing partition.
- * dwNumSectors - Number of logical sectors of the partition. USE_REMAINING_SPACE
- * to indicate to take up the rest of the space on the flash for that partition (should
- * only be used when creating extended partitions). This parameter is ignored
- * if opening existing partition.
- * dwPartType - Type of partition to create/open.
- * fActive - TRUE indicates to create/open the active partition. FALSE for
- * inactive.
- * dwCreationFlags - PART_CREATE_NEW to create only. Fail if it already
- * exists. PART_OPEN_EXISTING to open only. Fail if it doesn't exist.
- * PART_OPEN_ALWAYS creates if it does not exist and opens if it
- * does exist.
- *
- * EXIT
- * Handle to the partition on success. INVALID_HANDLE_VALUE on error.
- */
- HANDLE BP_OpenPartition(DWORD dwStartSector, DWORD dwNumSectors, DWORD dwPartType, BOOL fActive, DWORD dwCreationFlags)
- //£¨×¢£ºÊ¾Àý´úÂëΪ±¾ÈË/uc1EBOOTÖзÖÇøʵÏÖÔ´Â루/uc1WINCE5.0+S3C2440+128MNAND,MBRдÔÚµÚ¸ö/uc1BLOCK£¬·ÖÒ»¸ö/uc1BINFS¸ñʽ·ÖÇøºÍÒ»¸ö/uc1FAT¸ñʽ·ÖÇø£©¡££©
- BOOL WriteRegionsToBootMedia(DWORD dwImageStart, DWORD dwImageLength, DWORD dwLaunchAddr)
在把SDRAM中的NK烧写到NAND中去之前,先创建一个BINFS分区。
hPart = BP_OpenPartition( (NK_START_BLOCK+1)*PAGES_PER_BLOCK, // next block of MBR BINFS_BLOCK*PAGES_PER_BLOCK,//SECTOR_TO_BLOCK_SIZE(FILE_TO_SECTOR_SIZE(dwBINFSPartLength))*PAGES_PER_BLOCK, //align to block
PART_BINFS,
TRUE,
PART_OPEN_ALWAYS);
第一个参数分区的起始sector 为(NK_START_BLOCK+1)*PAGES_PER_BLOCK,
第二个参数分区的结束 sector为BINFS_BLOCK*PAGES_PER_BLOCK,
第三个参数分区的格式为PART_BINFS,即BINFS格式,
第四个参数指示该分区为活动分区,fActive = TURE,
第五个参数PART_OPEN_ALWAYS指示如果分区不存在就创建该分区,存在就OPEN该分区,返回分区句柄。
Code Snippet
- HANDLE BP_OpenPartition(DWORD dwStartSector, DWORD dwNumSectors, DWORD dwPartType, BOOL fActive, DWORD dwCreationFlags)
- {
- DWORD dwPartIndex;
- BOOL fExists;
- ASSERT (g_pbMBRSector);
- if (!IsValidMBR()) {
- DWORD dwFlags = 0;
- //fly
- RETAILMSG(1, (TEXT("BP_OpenPartition:: dwStartSector=0x%x ,dwNumSectors= 0x%x.,dwPartType = 0x%x/r/n"), dwStartSector, dwNumSectors,dwPartType));
- if (dwCreationFlags == PART_OPEN_EXISTING) {
- RETAILMSG(1, (TEXT("OpenPartition: Invalid MBR. Cannot open existing partition 0x%x./r/n"), dwPartType));
- return INVALID_HANDLE_VALUE;
- }
- RETAILMSG(1, (TEXT("OpenPartition: Invalid MBR. Formatting flash./r/n")));
- if (g_FlashInfo.flashType == NOR) {
- dwFlags |= FORMAT_SKIP_BLOCK_CHECK;
- }
- //fly
- RETAILMSG(1, (TEXT("BP_LowLevelFormat: g_pbMBRSector=0x%x, g_dwMBRSectorNum= 0x%x./r/n"), *g_pbMBRSector, g_dwMBRSectorNum));
- BP_LowLevelFormat (SECTOR_TO_BLOCK(dwStartSector), SECTOR_TO_BLOCK(dwNumSectors), dwFlags);
- dwPartIndex = 0;
- fExists = FALSE;
- }
- else {
- fExists = GetPartitionTableIndex(dwPartType, fActive, &dwPartIndex);
- }
- RETAILMSG(1, (TEXT("OpenPartition: Partition Exists=0x%x for part 0x%x./r/n"), fExists, dwPartType));
- if (fExists) {
- // Partition was found.
- if (dwCreationFlags == PART_CREATE_NEW)
- return INVALID_HANDLE_VALUE;
- if (g_partStateTable[dwPartIndex].pPartEntry == NULL) {
- // Open partition. If this is the boot section partition, then file pointer starts after MBR
- g_partStateTable[dwPartIndex].pPartEntry = (PPARTENTRY)(g_pbMBRSector + PARTTABLE_OFFSET + sizeof(PARTENTRY)*dwPartIndex);
- g_partStateTable[dwPartIndex].dwDataPointer = 0;
- }
- if ( dwNumSectors > g_partStateTable[dwPartIndex].pPartEntry->Part_TotalSectors )
- return CreatePartition (dwStartSector, dwNumSectors, dwPartType, fActive, dwPartIndex);
- else
- return (HANDLE)&g_partStateTable[dwPartIndex];
- }
- else {
- // If there are already 4 partitions, or creation flag specified OPEN_EXISTING, fail.
- if ((dwPartIndex == NUM_PARTS) || (dwCreationFlags == PART_OPEN_EXISTING))
- return INVALID_HANDLE_VALUE;
- // Create new partition
- return CreatePartition (dwStartSector, dwNumSectors, dwPartType, fActive, dwPartIndex);
- }
- return INVALID_HANDLE_VALUE;
- }
进入函数,首先做的事就是检测MBR的有效性。通过函数IsValidMBR()实现。
检测MBR的有效性,首先要知道MBR保存在哪里,前面说过NANDFLASH的第0 BLOCK,第1 Sector为主引导扇区,也就是MBR,但是NAND如果被当作启动芯片,○地址一般被BOOTLOADER代码占据,MBR只有放在后面的BLOCK中。所以我把第0 个BLOCK放NBOOT,第1个BLOCK放TOC,第2个BLOCK放EBOOT,第3个BLOCK保留,第4个BLOCK就放MBR。
Code Snippet
- static BOOL IsValidMBR()
- {
- // Check to see if the MBR is valid
- // MBR block is always located at logical sector 0
- g_dwMBRSectorNum = GetMBRSectorNum();
- RETAILMSG (1, (TEXT("IsValidMBR: MBR sector = 0x%x/r/n"), g_dwMBRSectorNum));
- if ((g_dwMBRSectorNum == INVALID_ADDR) || !FMD_ReadSector (g_dwMBRSectorNum, g_pbMBRSector, NULL, 1)) {
- RETAILMSG (1, (TEXT("IsValidMBR-----return FALSE-------------------/r/n")));
- return FALSE;
- }
- return ((g_pbMBRSector[0] == 0xE9) &&
- (g_pbMBRSector[1] == 0xfd) &&
- (g_pbMBRSector[2] == 0xff) &&
- (g_pbMBRSector[SECTOR_SIZE_FS-2] == 0x55) &&
- (g_pbMBRSector[SECTOR_SIZE_FS-1] == 0xAA));
- }
IsValidMBR()实现的第一行就是给全局变量g_dwMBRSectorNum 赋值,显而易见,g_dwMBRSectorNum就是指示保存MBR的那个Sector了。
g_dwMBRSectorNum = GetMBRSectorNum(); //是获得保存MBR的那个Sector
Code Snippet
- static DWORD GetMBRSectorNum ()
- {
- DWORD dwBlockNum = 3, dwSector = 0;
- SectorInfo si;
- while (dwBlockNum < g_FlashInfo.dwNumBlocks) {
- if (!IS_BLOCK_UNUSABLE (dwBlockNum)) {
- dwSector = dwBlockNum * g_FlashInfo.wSectorsPerBlock;
- if (!FMD_ReadSector (dwSector, NULL, &si, 1)) {
- RETAILMSG(1, (TEXT("GetMBRSectorNum: Could not read sector 0x%x./r/n"), dwSector));
- return INVALID_ADDR;
- }
- // Check to see if logical sector number is 0
- if (si.dwReserved1 == 0) {
- //RETAILMSG(1,(TEXT("dwBlockNum=%d/r/n"),dwBlockNum));
- return dwSector;
- }
- }
- dwBlockNum++;
- }
- return INVALID_ADDR;
- }
这里dwBlockNum直接给了个3,因为NBOOT,TOC,EBOOT已经把前三个BLOCK用了。所以MBR的选择直接排除了前三个BLOCK了。
#define IS_BLOCK_UNUSABLE(blockID) ((FMD_GetBlockStatus (blockID) & (BLOCK_STATUS_BAD|BLOCK_STATUS_RESERVED)) > 0)
然后确定BLOCK是否可使用的BLOCK,最后通si.dwReserved1 == 0来判断是不是选择这个Sector来保存MBR。
IsValidMBR()中还有一个重要的结构就是g_pbMBRSector数组,它就是MBR了。
函数返回时,MBR必须符合下列记录。
return ((g_pbMBRSector[0] == 0xE9) &&
(g_pbMBRSector[1] == 0xfd) &&
(g_pbMBRSector[2] == 0xff) &&
(g_pbMBRSector[SECTOR_SIZE_FS-2] == 0x55) &&
(g_pbMBRSector[SECTOR_SIZE_FS-1] == 0xAA));
可以看到只有开始三个字节为0XE9,FD,FF,当然,还有熟悉的结束标志符0X55AA。
如果没有检测到MBR,则先对NANDFLASH进行低级格式化。BP_LowLevelFormat (SECTOR_TO_BLOCK(dwStartSector), SECTOR_TO_BLOCK(dwNumSectors), dwFlags);再创建分区,CreatePartition (dwStartSector, dwNumSectors, dwPartType, fActive, dwPartIndex);。
Code Snippet
- BOOL BP_LowLevelFormat(DWORD dwStartBlock, DWORD dwNumBlocks, DWORD dwFlags)
- {
- dwNumBlocks = min (dwNumBlocks, g_FlashInfo.dwNumBlocks);
- RETAILMSG(1,(TEXT("fly::Enter LowLevelFormat [0x%x, 0x%x]./r/n"), dwStartBlock,dwNumBlocks));// dwStartBlock + dwNumBlocks - 1));
- // Erase all the flash blocks.
- if (!EraseBlocks(dwStartBlock, dwNumBlocks, dwFlags))
- return(FALSE);
- // Determine first good starting block
- while (IS_BLOCK_UNUSABLE (dwStartBlock) && dwStartBlock < g_FlashInfo.dwNumBlocks) {
- dwStartBlock++;
- }
- if (dwStartBlock >= g_FlashInfo.dwNumBlocks) {
- RETAILMSG(1,(TEXT("BP_LowLevelFormat: no good blocks/r/n")));
- return FALSE;
- }
- // MBR goes in the first sector of the starting block. This will be logical sector 0.
- g_dwMBRSectorNum = dwStartBlock * g_FlashInfo.wSectorsPerBlock;
- RETAILMSG(1,(TEXT("fly:g_dwMBRSectorNum=%d/r/n"),g_dwMBRSectorNum));
- // Create an MBR.
- CreateMBR();
- return(TRUE);
- }
在对NANDFLASH进行低格时,主要对坏块的处理。if (!EraseBlocks(dwStartBlock, dwNumBlocks, dwFlags))检测每一个Sector,每个BLOCK只要有一个Sector不能读写这个块都会被处理成坏块,这样才能保证系统的稳定性。在函数的最后调用了 CreateMBR();来创建一个MBR。
Code Snippet
- static BOOL CreateMBR()
- {
- // This, plus a valid partition table, is all the CE partition manager needs to recognize
- // the MBR as valid. It does not contain boot code.
- memset (g_pbMBRSector, 0xff, g_FlashInfo.wDataBytesPerSector);
- g_pbMBRSector[0] = 0xE9;
- g_pbMBRSector[1] = 0xfd;
- g_pbMBRSector[2] = 0xff;
- g_pbMBRSector[SECTOR_SIZE_FS-2] = 0x55;
- g_pbMBRSector[SECTOR_SIZE_FS-1] = 0xAA;
- // Zero out partition table so that mspart treats entries as empty.
- memset (g_pbMBRSector+PARTTABLE_OFFSET, 0, sizeof(PARTENTRY) * NUM_PARTS);
- return WriteMBR();
- }
当然。因为还没有进行分区,这里写入的MBR分区表部分是空的。
Code Snippet
- static BOOL WriteMBR()
- {
- DWORD dwMBRBlockNum = g_dwMBRSectorNum / g_FlashInfo.wSectorsPerBlock;
- //dwMBRBlockNum = 1 ;
- RETAILMSG(1, (TEXT("WriteMBR: MBR block = 0x%x,g_dwMBRSectorNum = 0x%x./r/n"), dwMBRBlockNum,g_dwMBRSectorNum));
- memset (g_pbBlock, 0xff, g_dwDataBytesPerBlock);
- memset (g_pSectorInfoBuf, 0xff, sizeof(SectorInfo) * g_FlashInfo.wSectorsPerBlock);
- // No need to check return, since a failed read means data hasn't been written yet.
- ReadBlock (dwMBRBlockNum, g_pbBlock, g_pSectorInfoBuf);
- if (!FMD_EraseBlock (dwMBRBlockNum)) {
- RETAILMSG (1, (TEXT("CreatePartition: error erasing block 0x%x/r/n"), dwMBRBlockNum));
- return FALSE;
- }
- memcpy (g_pbBlock + (g_dwMBRSectorNum % g_FlashInfo.wSectorsPerBlock) * g_FlashInfo.wDataBytesPerSector, g_pbMBRSector, g_FlashInfo.wDataBytesPerSector);
- g_pSectorInfoBuf->bOEMReserved &= ~OEM_BLOCK_READONLY;
- g_pSectorInfoBuf->wReserved2 &= ~SECTOR_WRITE_COMPLETED;
- g_pSectorInfoBuf->dwReserved1 = 0;
- RETAILMSG(1, (TEXT("fly::WriteMBR: MBR block = 0x%x./r/n"), dwMBRBlockNum));
- if (!WriteBlock (dwMBRBlockNum, g_pbBlock, g_pSectorInfoBuf)) {
- RETAILMSG (1, (TEXT("CreatePartition: could not write to block 0x%x/r/n"), dwMBRBlockNum));
- return FALSE;
- }
- return TRUE;
- }
在WriteMBR()函数中,就写入了判断MBR 的一些标志到BLOCK, g_pSectorInfoBuf->bOEMReserved &= ~OEM_BLOCK_READONLY;
g_pSectorInfoBuf->wReserved2 &= ~SECTOR_WRITE_COMPLETED;
g_pSectorInfoBuf->dwReserved1 = 0;
Wince系统启动时,具体是NANDFLASH驱动加载成功后,MOUNT文件系统到NANDFLASH之前,也会通过读取这些SectorInfo来得到MBR 保存的BLOCK,进而读取MBR,获得分区信息,从而把各分区MOUNT到相应文件系统。格式化完成,MBR也写入成功后就可以开始新建分区了。
Code Snippet
- /* CreatePartition
- *
- * Creates a new partition. If it is a boot section partition, then it formats
- * flash.
- *
- * ENTRY
- * dwStartSector - Logical sector to start the partition. NEXT_FREE_LOC if
- * none specified.
- * dwNumSectors - Number of logical sectors of the partition. USE_REMAINING_SPACE
- * to indicate to take up the rest of the space on the flash for that partition.
- * dwPartType - Type of partition to create.
- * fActive - TRUE indicates to create the active partition. FALSE for
- * inactive.
- * dwPartIndex - Index of the partition entry on the MBR
- *
- * EXIT
- * Handle to the partition on success. INVALID_HANDLE_VALUE on error.
- */
- static HANDLE CreatePartition (DWORD dwStartSector, DWORD dwNumSectors, DWORD dwPartType, BOOL fActive, DWORD dwPartIndex)
- {
- DWORD dwBootInd = 0;
- RETAILMSG(1, (TEXT("CreatePartition: Enter CreatePartition for 0x%x./r/n"), dwPartType));
- if (fActive)
- dwBootInd |= PART_IND_ACTIVE;
- if (dwPartType == PART_BOOTSECTION || dwPartType == PART_BINFS || dwPartType == PART_XIP)
- dwBootInd |= PART_IND_READ_ONLY;
- // If start sector is invalid, it means find next free sector
- if (dwStartSector == NEXT_FREE_LOC) {
- dwStartSector = FindFreeSector();
- if (dwStartSector == INVALID_ADDR) {
- RETAILMSG(1, (TEXT("CreatePartition: can't find free sector./r/n")));
- return INVALID_HANDLE_VALUE;
- }
- // Start extended partition on a block boundary
- if ((dwPartType == PART_EXTENDED) && (dwStartSector % g_FlashInfo.wSectorsPerBlock)) {
- dwStartSector = (dwStartSector / g_FlashInfo.wSectorsPerBlock + 1) * g_FlashInfo.wSectorsPerBlock;
- }
- }
- // If num sectors is invalid, fill the rest of the space up
- if (dwNumSectors == USE_REMAINING_SPACE) {
- DWORD dwLastLogSector = LastLogSector();
- if (dwLastLogSector == INVALID_ADDR)
- return INVALID_HANDLE_VALUE;
- // Determine the number of blocks to reserve for the FAL compaction when creating an extended partition.
- DWORD dwReservedBlocks = g_FlashInfo.dwNumBlocks / PERCENTAGE_OF_MEDIA_TO_RESERVE;
- if((dwReservedBlocks = g_FlashInfo.dwNumBlocks / PERCENTAGE_OF_MEDIA_TO_RESERVE) < MINIMUM_FLASH_BLOCKS_TO_RESERVE) {
- dwReservedBlocks = MINIMUM_FLASH_BLOCKS_TO_RESERVE;
- }
- dwNumSectors = dwLastLogSector - dwStartSector + 1 - dwReservedBlocks * g_FlashInfo.wSectorsPerBlock;
- }
- if (!AreSectorsFree (dwStartSector, dwNumSectors)){
- RETAILMSG (1, (TEXT("fly:::::CreatePartition: sectors [0x%x, 0x%x] requested are out of range or taken by another partition/r/n"), dwStartSector, dwNumSectors));
- return INVALID_HANDLE_VALUE;
- }
- RETAILMSG(1, (TEXT("CreatePartition: Start = 0x%x, Num = 0x%x./r/n"), dwStartSector, dwNumSectors));
- AddPartitionTableEntry (dwPartIndex, dwStartSector, dwNumSectors, (BYTE)dwPartType, (BYTE)dwBootInd);
- if (dwBootInd & PART_IND_READ_ONLY) {
- if (!WriteLogicalNumbers (dwStartSector, dwNumSectors, TRUE)) {
- RETAILMSG(1, (TEXT("CreatePartition: can't mark sector info./r/n")));
- return INVALID_HANDLE_VALUE;
- }
- }
- if (!WriteMBR())
- return INVALID_HANDLE_VALUE;
- g_partStateTable[dwPartIndex].pPartEntry = (PPARTENTRY)(g_pbMBRSector + PARTTABLE_OFFSET + sizeof(PARTENTRY)*dwPartIndex);
- g_partStateTable[dwPartIndex].dwDataPointer = 0;
- return (HANDLE)&g_partStateTable[dwPartIndex];
- }
如果第二个参数为-1,则视为将余下的所有空间划为一个分区。LastLogSector();函数获得最后一个逻辑Sector。
Code Snippet
- static DWORD LastLogSector()
- {
- if (g_dwLastLogSector) {
- return g_dwLastLogSector;
- }
- DWORD dwMBRBlock = g_dwMBRSectorNum / g_FlashInfo.wSectorsPerBlock;
- DWORD dwUnusableBlocks = dwMBRBlock;
- for (DWORD i = dwMBRBlock; i < g_FlashInfo.dwNumBlocks; i++) {
- if (IS_BLOCK_UNUSABLE (i))
- dwUnusableBlocks++;
- }
- g_dwLastLogSector = (g_FlashInfo.dwNumBlocks - dwUnusableBlocks) * g_FlashInfo.wSectorsPerBlock - 1;
- RETAILMSG(1, (TEXT("fly:::LastLogSector: Last log sector is: 0x%x./r/n"), g_dwLastLogSector));
- return g_dwLastLogSector;
- }
即g_dwLastLogSector = (g_FlashInfo.dwNumBlocks - dwUnusableBlocks) * g_FlashInfo.wSectorsPerBlock - 1;//(NAND 的BLOCK总数 – MBR保存的那个BLOCK)* 每个BLOCK的Sector数 – 保存MBR的那个Sector。得到的就是从MBR那个Sector之后的所有Sector,即逻辑大小。
AreSectorsFree (dwStartSector, dwNumSectors)函数判断参数提供的起始Sector和个数有没有超出来NAND的界限,或者逻辑分区的界限。
重头戏开始了。通过AddPartitionTableEntry (dwPartIndex, dwStartSector, dwNumSectors, (BYTE)dwPartType, (BYTE)dwBootInd); 准备分区信息写入分区表。
Code Snippet
- /* AddPartitionTableEntry
- *
- * Generates the partition entry for the partition table and copies the entry
- * into the MBR that is stored in memory.
- *
- *
- * ENTRY
- * entry - index into partition table
- * startSector - starting logical sector
- * totalSectors - total logical sectors
- * fileSystem - type of partition
- * bootInd - byte in partition entry that stores various flags such as
- * active and read-only status.
- *
- * EXIT
- */
- static void AddPartitionTableEntry(DWORD entry, DWORD startSector, DWORD totalSectors, BYTE fileSystem, BYTE bootInd)
- {
- PARTENTRY partentry = {0};
- Addr startAddr;
- Addr endAddr;
- ASSERT(entry < 4);
- // no checking with disk info and start/total sectors because we allow
- // bogus partitions for testing purposes
- // initially known partition table entry
- partentry.Part_BootInd = bootInd;
- partentry.Part_FileSystem = fileSystem;
- partentry.Part_StartSector = startSector;
- partentry.Part_TotalSectors = totalSectors;
- // logical block addresses for the first and final sector (start on the second head)
- startAddr.type = LBA;
- startAddr.lba = partentry.Part_StartSector;
- endAddr.type = LBA;
- endAddr.lba = partentry.Part_StartSector + partentry.Part_TotalSectors-1;
- // translate the LBA addresses to CHS addresses
- startAddr = LBAtoCHS(&g_FlashInfo, startAddr);
- endAddr = LBAtoCHS(&g_FlashInfo, endAddr);
- // starting address
- partentry.Part_FirstTrack = (BYTE)(startAddr.chs.cylinder & 0xFF);
- partentry.Part_FirstHead = (BYTE)(startAddr.chs.head & 0xFF);
- // lower 6-bits == sector, upper 2-bits = cylinder upper 2-bits of 10-bit cylinder #
- partentry.Part_FirstSector = (BYTE)((startAddr.chs.sector & 0x3F) | ((startAddr.chs.cylinder & 0x0300) >> 2));
- // ending address:
- partentry.Part_LastTrack = (BYTE)(endAddr.chs.cylinder & 0xFF);
- partentry.Part_LastHead = (BYTE)(endAddr.chs.head & 0xFF);
- // lower 6-bits == sector, upper 2-bits = cylinder upper 2-bits of 10-bit cylinder #
- partentry.Part_LastSector = (BYTE)((endAddr.chs.sector & 0x3F) | ((endAddr.chs.cylinder & 0x0300) >> 2));
- memcpy(g_pbMBRSector+PARTTABLE_OFFSET+(sizeof(PARTENTRY)*entry), &partentry, sizeof(PARTENTRY));
- }
这里面的地址信息是一种叫CHS(Cyinder/Head/Sector)的地址。eboot中有将逻辑地址LBS(Logical Block Addr)与这种地址互相转换的函数LBAtoCHS,CHSToLBA。
Code Snippet
- Addr LBAtoCHS(FlashInfo *pFlashInfo, Addr lba)
- {
- Addr chs;
- DWORD tmp = pFlashInfo->dwNumBlocks * pFlashInfo->wSectorsPerBlock;
- chs.type = CHS;
- chs.chs.cylinder = (WORD)(lba.lba / tmp); // ÖùÃæ,Ó¦¸ÃʼÖÕÊÇ
- tmp = lba.lba % tmp;
- chs.chs.head = (WORD)(tmp / pFlashInfo->wSectorsPerBlock); // ¿éµØÖ·
- chs.chs.sector = (WORD)((tmp % pFlashInfo->wSectorsPerBlock) + 1); // ÉÈÇø+1
- return chs;
- }
- Addr CHStoLBA(FlashInfo *pFlashInfo, Addr chs)
- {
- Addr lba;
- lba.type = LBA;
- lba.lba = ((chs.chs.cylinder * pFlashInfo->dwNumBlocks + chs.chs.head)
- * pFlashInfo->wSectorsPerBlock)+ chs.chs.sector - 1;
- return lba;
- }
如果分区的格式有只读属性,则通过WriteLogicalNumbers()函数写分区的Sectorinfo,把这部分空间保护起来。
Code Snippet
- static BOOL WriteLogicalNumbers (DWORD dwStartSector, DWORD dwNumSectors, BOOL fReadOnly)
- {
- DWORD dwNumSectorsWritten = 0;
- DWORD dwPhysSector = Log2Phys (dwStartSector);
- DWORD dwBlockNum = dwPhysSector / g_FlashInfo.wSectorsPerBlock;
- DWORD dwOffset = dwPhysSector % g_FlashInfo.wSectorsPerBlock;
- while (dwNumSectorsWritten < dwNumSectors) {
- // If bad block, move to the next block
- if (IS_BLOCK_UNUSABLE (dwBlockNum)) {
- dwBlockNum++;
- continue;
- }
- memset (g_pbBlock, 0xff, g_dwDataBytesPerBlock);
- memset (g_pSectorInfoBuf, 0xff, sizeof(SectorInfo) * g_FlashInfo.wSectorsPerBlock);
- // No need to check return, since a failed read means data hasn't been written yet.
- ReadBlock (dwBlockNum, g_pbBlock, g_pSectorInfoBuf);
- if (!FMD_EraseBlock (dwBlockNum)) {
- return FALSE;
- }
- DWORD dwSectorsToWrite = g_FlashInfo.wSectorsPerBlock - dwOffset;
- PSectorInfo pSectorInfo = g_pSectorInfoBuf + dwOffset;
- // If this is the last block, then calculate sectors to write if there isn't a full block to update
- if ((dwSectorsToWrite + dwNumSectorsWritten) > dwNumSectors)
- dwSectorsToWrite = dwNumSectors - dwNumSectorsWritten;
- for (DWORD iSector = 0; iSector < dwSectorsToWrite; iSector++, pSectorInfo++, dwNumSectorsWritten++) {
- // Assert read only by setting bit to 0 to prevent wear-leveling by FAL
- if (fReadOnly)
- pSectorInfo->bOEMReserved &= ~OEM_BLOCK_READONLY;
- // Set to write completed so FAL can map the sector
- pSectorInfo->wReserved2 &= ~SECTOR_WRITE_COMPLETED;
- // Write the logical sector number
- pSectorInfo->dwReserved1 = dwStartSector + dwNumSectorsWritten;
- }
- if (!WriteBlock (dwBlockNum, g_pbBlock, g_pSectorInfoBuf))
- return FALSE;
- dwOffset = 0;
- dwBlockNum++;
- }
- return TRUE;
- }
这就是为什么系统启动后,我们无法写入文件的BINFS文件系统格式分区的原因了。而FAT格式就可以。最后调用WriteMBR()完全MBR的写入,分区完毕。
让我们继续回到BP_OpenPartition函数中,如果从一开始IsValidMBR()就检测到有效的MBR,GetPartitionTableIndex(dwPartType, fActive, &dwPartIndex);获得分区表。和dwPartIndex分区表的索引号。
Code Snippet
- static BOOL GetPartitionTableIndex (DWORD dwPartType, BOOL fActive, PDWORD pdwIndex)
- {
- PPARTENTRY pPartEntry = (PPARTENTRY)(g_pbMBRSector + PARTTABLE_OFFSET);
- DWORD iEntry = 0;
- for (iEntry = 0; iEntry < NUM_PARTS; iEntry++, pPartEntry++) {
- if ((pPartEntry->Part_FileSystem == dwPartType) && (((pPartEntry->Part_BootInd & PART_IND_ACTIVE) != 0) == fActive)) {
- *pdwIndex = iEntry;
- return TRUE;
- }
- if (!IsValidPart (pPartEntry)) {
- *pdwIndex = iEntry;
- return FALSE;
- }
- }
- return FALSE;
- }
重要结构:PARTENTRY
Code Snippet
- // end of master boot record contains 4 partition entries
- typedef struct _PARTENTRY {
- BYTE Part_BootInd; // If 80h means this is boot partition
- BYTE Part_FirstHead; // Partition starting head based 0
- BYTE Part_FirstSector; // Partition starting sector based 1
- BYTE Part_FirstTrack; // Partition starting track based 0
- BYTE Part_FileSystem; // Partition type signature field
- BYTE Part_LastHead; // Partition ending head based 0
- BYTE Part_LastSector; // Partition ending sector based 1
- BYTE Part_LastTrack; // Partition ending track based 0
- DWORD Part_StartSector; // Logical starting sector based 0
- DWORD Part_TotalSectors; // Total logical sectors in partition
- } PARTENTRY;
分区表就是通过这个结构写入MBR,起始地址,分区大小,分区格式,对应结构写入MBR所在的Sector就可以了。在检测有效分区时static BOOL IsValidPart (PPARTENTRY pPartEntry)
{
return (pPartEntry->Part_FileSystem != 0xff) && (pPartEntry->Part_FileSystem != 0);
}
就是通过对分区表文件系统格式的判断了。
把NAND后面的空间,全部分为一个FAT格式的分区。
Code Snippet
- // create extended partition in whatever is left
- hPartEx = BP_OpenPartition( (NK_START_BLOCK+1+BINFS_BLOCK) * PAGES_PER_BLOCK,
- NEXT_FREE_LOC, // (1024 - (NK_START_BLOCK+1+SECTOR_TO_BLOCK_SIZE(FILE_TO_SECTOR_SIZE(dwBINFSPartLength)))) * PAGES_PER_BLOCK,
- PART_DOS32,
- TRUE,
- PART_OPEN_ALWAYS);
- if (hPartEx == INVALID_HANDLE_VALUE )
- {
- EdbgOutputDebugString("*** WARN: StoreImageToBootMedia: Failed to open/create Extended partition ***/r/n");
- }
引用通告
此日志的引用通告 URL 是:
http://giwawe.spaces.live.com/blog/cns!92AFEF096943066B!260.trak
引用此项的网络日志