stm32 pwm频率从2K到4K



u16 minarr = 249;
u16 maxarr = 499;
u16 i = 0;
void TIM3_IRQHandler(void)   //TIM3中断
{
 u8 ReadValue;
 if (TIM_GetITStatus(TIM3, TIM_IT_Update) != RESET) //检查指定的TIM中断发生与否:TIM 中断源
 {
  TIM_ClearITPendingBit(TIM3, TIM_IT_Update  );  //清除TIMx的中断待处理位:TIM 中断源
 }
 if(maxarr > minarr ){
  maxarr -= 50;
  TIM3->ARR = maxarr;
  TIM3->CCR1 = (maxarr+1)/2;//占空比50%
 } else{
  TIM_Cmd(TIM3, DISABLE);
 }
}

//PWM输出初始化
//arr：自动重装值
//psc：时钟预分频数
void TIM3_PWM_Init(u16 arr,u16 psc)
{ 
 GPIO_InitTypeDef GPIO_InitStructure;
 TIM_TimeBaseInitTypeDef  TIM_TimeBaseStructure;
 TIM_OCInitTypeDef  TIM_OCInitStructure;
 NVIC_InitTypeDef NVIC_InitStructure;
 

 RCC_APB1PeriphClockCmd(RCC_APB1Periph_TIM3, ENABLE);                     //使能定时器3时钟
//  RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB  | RCC_APB2Periph_AFIO, ENABLE);//使能GPIO外设和AFIO复用功能模块时钟
  RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA  | RCC_APB2Periph_AFIO, ENABLE);

//  GPIO_PinRemapConfig(GPIO_PartialRemap_TIM3, ENABLE);                        //Timer3部分重映射  TIM3_CH2->PB5   
 
   /*设置该引脚为复用输出功能,输出TIM3 CH2的PWM脉冲波形 GPIOB.5*/
 GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7;        //TIM_CH2
 GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;  //复用推挽输出
 GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
 GPIO_Init(GPIOA, &GPIO_InitStructure);           //初始化GPIO
 
   /*初始化TIM3*/
 TIM_TimeBaseStructure.TIM_Period = arr; //设置在下一个更新事件装入活动的自动重装载寄存器周期的值
 TIM_TimeBaseStructure.TIM_Prescaler =psc; //设置用来作为TIMx时钟频率除数的预分频值
 TIM_TimeBaseStructure.TIM_ClockDivision = 0; //设置时钟分割:TDTS = Tck_tim,TIM3时钟为72MHZ
 TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;  //TIM向上计数模式
 TIM_TimeBaseInit(TIM3, &TIM_TimeBaseStructure); //根据TIM_TimeBaseInitStruct中指定的参数初始化TIMx的时间基数单位
 
 /*初始化TIM3 Channel2 PWM模式*/ 
 TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM2; //选择定时器模式:TIM脉冲宽度调制模式2
  TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable; //比较输出使能
 TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High; //输出极性:TIM输出比较极性高
 TIM_OCInitStructure.TIM_Pulse = 0;
 TIM_OC2Init(TIM3, &TIM_OCInitStructure);  //根据T指定的参数初始化外设TIM3 OC2

 TIM_OC2PreloadConfig(TIM3, TIM_OCPreload_Enable);  //使能TIM3在CCR2上的预装载寄存器
 
 
 TIM_ITConfig(  //使能或者失能指定的TIM中断
  TIM3, //TIM3
  TIM_IT_Update ,
  ENABLE  //使能
  );
 NVIC_InitStructure.NVIC_IRQChannel = TIM3_IRQn;  //TIM3中断
 NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0;  //先占优先级0级
 NVIC_InitStructure.NVIC_IRQChannelSubPriority = 3;  //从优先级3级
 NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; //IRQ通道被使能
 NVIC_Init(&NVIC_InitStructure);  //根据NVIC_InitStruct中指定的参数初始化外设NVIC寄存器
 
 TIM_Cmd(TIM3, ENABLE);  //使能TIM3
}

int main(void)
 {
 
 GPIO_InitTypeDef gpio;
 

 gpio.GPIO_Pin = GPIO_Pin_2;
 gpio.GPIO_Speed = GPIO_Speed_50MHz;
 gpio.GPIO_Mode = GPIO_Mode_Out_PP;
 GPIO_Init(GPIOA, &gpio);

 GPIO_SetBits(GPIOA, GPIO_Pin_2);
 GPIO_SetBits(GPIOA, GPIO_Pin_7);

  TIM3_PWM_Init(499,71);    //PWM 频率=72000000/(500*72)=2khz， 周期=0.0005s

  while(1)
  {
  }

 }

结果