NRR52832 获取扫描请求

 扫描请求包的格式如下：

 

 

1.在 ble_advertising_start 中将p_advertising->peer_addr_reply_expected 设置为 true;

uint32_t ble_advertising_start(ble_advertising_t * const p_advertising,
                               ble_adv_mode_t            advertising_mode)
{
     uint32_t ret;

    if (p_advertising->initialized == false)
    {
        return NRF_ERROR_INVALID_STATE;
    }

    p_advertising->adv_mode_current = advertising_mode;

    memset(&p_advertising->peer_address, 0, sizeof(p_advertising->peer_address));

    if (  ((p_advertising->adv_modes_config.ble_adv_directed_high_duty_enabled) && (p_advertising->adv_mode_current == BLE_ADV_MODE_DIRECTED_HIGH_DUTY))
        ||((p_advertising->adv_modes_config.ble_adv_directed_enabled)           && (p_advertising->adv_mode_current == BLE_ADV_MODE_DIRECTED_HIGH_DUTY))
        ||((p_advertising->adv_modes_config.ble_adv_directed_enabled)           && (p_advertising->adv_mode_current == BLE_ADV_MODE_DIRECTED))
       )
    {
        if (p_advertising->evt_handler != NULL)
        {
            p_advertising->peer_addr_reply_expected = true;
            p_advertising->evt_handler(BLE_ADV_EVT_PEER_ADDR_REQUEST);
        }
        else
        {
            p_advertising->peer_addr_reply_expected = false;
        }
    }

    p_advertising->adv_mode_current = adv_mode_next_avail_get(p_advertising, advertising_mode);

    // Fetch the whitelist.
    if ((p_advertising->evt_handler != NULL) &&
        (p_advertising->adv_mode_current == BLE_ADV_MODE_FAST || p_advertising->adv_mode_current == BLE_ADV_MODE_SLOW) &&
        (p_advertising->adv_modes_config.ble_adv_whitelist_enabled) &&
        (!p_advertising->whitelist_temporarily_disabled))
    {
        p_advertising->whitelist_in_use         = false;
        p_advertising->whitelist_reply_expected = true;
        p_advertising->evt_handler(BLE_ADV_EVT_WHITELIST_REQUEST);
    }
    else
    {
        p_advertising->whitelist_reply_expected = false;
    }

    // Initialize advertising parameters with default values.
    memset(&p_advertising->adv_params, 0, sizeof(p_advertising->adv_params));

    p_advertising->adv_params.properties.type = BLE_GAP_ADV_TYPE_CONNECTABLE_SCANNABLE_UNDIRECTED;

    // Use 1MBIT as primary phy if no phy was selected.
    if (phy_is_valid(&p_advertising->adv_modes_config.ble_adv_primary_phy))
    {
        p_advertising->adv_params.primary_phy = p_advertising->adv_modes_config.ble_adv_primary_phy;
    }
    else
    {
        p_advertising->adv_params.primary_phy = BLE_GAP_PHY_1MBPS;
    }

    if (p_advertising->adv_modes_config.ble_adv_extended_enabled)
    {
        // Use 1MBIT as secondary phy if no phy was selected.
        if (phy_is_valid(&p_advertising->adv_modes_config.ble_adv_primary_phy))
        {
            p_advertising->adv_params.secondary_phy = p_advertising->adv_modes_config.ble_adv_secondary_phy;
        }
        else
        {
            p_advertising->adv_params.secondary_phy = BLE_GAP_PHY_1MBPS;
        }
    }
    p_advertising->adv_params.filter_policy = BLE_GAP_ADV_FP_ANY;

    // Set advertising parameters and events according to selected advertising mode.
    switch (p_advertising->adv_mode_current)
    {
        case BLE_ADV_MODE_DIRECTED_HIGH_DUTY:
            ret = set_adv_mode_directed_high_duty(p_advertising, &p_advertising->adv_params);
            break;