泰凌微方案键鼠套装

键盘自动发数字测试代码

u8 rf_test_auto_snd_count() // @test
{
	static u16 test_num = 0;
	static u8 test_12ms_cnt = 0;
	u8 temp = 0;
	if(PowerOnFastConntTicks){
		return 0;
	}
	memset(keyboard_buf_aaa, 0, sizeof(keyboard_buf_aaa));
	memset(key_buf_aaa.keycode,0,6); // 0
	switch(++test_12ms_cnt % 20){
		case 1:
			temp = (test_num/1000)%10;
			key_buf_aaa.keycode[0] = (temp == 0) ? KB_0 : (temp - 1 + KB_1);
			break;
		case 2:
		case 4:
		case 6:
		case 8:
		case 10:key_buf_aaa.press_cnt = 0;
			break;

		case 3:
			temp = (test_num/100)%10;
			key_buf_aaa.keycode[0] = (temp == 0) ? KB_0 : (temp - 1 + KB_1);
			break;

		case 5:
			temp = (test_num/10)%10; // 0
			key_buf_aaa.keycode[0] = (temp == 0) ? KB_0 : (temp - 1 + KB_1);
			break;

		case 7:
			temp = (test_num)%10;
			key_buf_aaa.keycode[0] = (temp == 0) ? KB_0 : (temp - 1 + KB_1);
			break;

		case 9:
			key_buf_aaa.keycode[0] = (++test_num&1) ? KB_Tab : KB_Enter; // 0
			break;
		default:
			return 0;
	}
	//key_buf_aaa.press_cnt = 1;
	return 1;
}

键盘工程修改代码

#define D24G_PAIR_TIMER_OUT 			350 //unit 1us
#define D24G_COMMUNICATION_TIMER_OUT	180 //unit 1us

void clear_pair_flag()
{
    pair_flag = 0;
    analog_write(USED_DEEP_ANA_REG1, ana_reg1_aaa & CLEAR_PAIR_ANA_FLAG);
    rf_rx_timeout_us = D24G_COMMUNICATION_TIMER_OUT;
}
void set_pair_flag()
{
    pair_flag = 1;
    analog_write(USED_DEEP_ANA_REG1, ana_reg1_aaa | PAIR_ANA_FLG);
    rf_rx_timeout_us = D24G_PAIR_TIMER_OUT;
}
void d24_main_loop()
{
 ......
#if SUIT_RF_HANDLE_ENABLE
	if(rf_state==RF_RX_TIMEOUT_STATUS){
		if(clock_time_exceed(tick_rf, 600)){	// ms rf_rx_timeout_us is 160us
			tick_rf = clock_time();
			d24g_rf_loop();
		}
	}else{
		tick_rf = clock_time();
		d24g_rf_loop();
	}
#endif
......
}

鼠标测试代码

static void test_auto_circle()
{
	s16 buff[8][2] = {
		{2000-1414, 	1414},
		{1414, 			2000-1414},
		{1414, 			-(2000-1414)},
		{2000-1414, 	-1414},

		{-(2000-1414), 	-1414},
		{-1414, 		-(2000-1414)},
		{-1414, 		2000-1414},
		{-(2000-1414), 	1414},
	};

	static u8 count = 0;
	ms_data.x += buff[count&0x07][0]/10;
	ms_data.y += buff[count&0x07][1]/10;
	count++;
	has_new_key_event |= SENSOR_DATA_EVENT_AAA;
}

鼠标修改代码

	#define D24G_COMMUNICATION_TIMER_OUT    160 // 240 //unit 1us

接收器工程不需修改

验证鼠标500回报率同时 键盘12ms间隔发 四万个四位数 未丢键