一、网络参数规划
1、FAS80xx网络接口规划集群网络连接
| A控制器 | B控制器 | 交换机 |
| e0a(万兆光口） | e0a(万兆光口） | 集群网络万兆交换机 |
| e0b(万兆光口） | e0b(万兆光口） | 集群网络万兆交换机 |
| e0c(万兆光口） | e0c(万兆光口） | 集群网络万兆交换机 |
| e0d(万兆光口） | e0d(万兆光口） | 集群网络万兆交换机 |
|
|
|
|
2、数据网络数据连接
|
A 控 制 器 | Slot0 | Slot4 | 接口组 | 交换机 |
| e0i(千兆） | e4a(千兆） | Vif01 | 数据交换机1 | |
| e0j(千兆） | e4b(千兆） | Vif02 | 数据交换机2 | |
| e0k(千兆） | e4c(千兆） | 备用 |
| |
| e0l(千兆） | e4d(千兆） | 备用 |
| |
|
B 控 制 器 | Slot0 | Slot4 | 接口组 | 交换机 |
| e0i(千兆） | e4a(千兆） | Vif01 | 数据交换机1 | |
| e0j(千兆） | e4b(千兆） | Vif02 | 数据交换机2 | |
| e0k(千兆） | e4c(千兆） |
|
| |
| e0l(千兆） | e4d(千兆） |
|
|
二: 集群规划
现阶段fas80xx A控制器作为主控建立集群cluster，B控制器加入到cluster,后期将FAS8040和FAS62xx等设备加入到这个cluster，进行集中统一管理。
1、创建集群
在集群模式 ONTAP 中创建集群的前提条件。
| 集群详细信息 | 集群详细信息值
|
| 集群名称 | <<var_clustername>> |
| 集群模式 ONTAP 基本许可证 | <<var_cluster_license>> |
| 集群管理端口 | e0M |
| 集群管理 IP 地址 | <<var_clustermgmt_IP>> |
| 集群管理网络掩码 | <<var_clustermgmt_netmask>> |
| 集群管理网关 | <<var_clustermgmt_gateway>> |
| DNS 域名 | nbl.bocapp.cn |
| DNS 名称服务器 | 30.0.11.48, 30.0.11.49 |
| 节点管理端口 | e0M |
| 节点管理 IP 地址 | <<var_node01_mgmt_IP>> |
| 节点管理网络掩码 | <<var_node01_mgmt_netmask>> |
| 节点管理网关 | <<var_node01_mgmt_gateway>> |
| 集群位置 | <<var_install_floor_room>> |
集群中的第一个节点将执行cluster create操作。所有其他节点将执行cluster join操作。集群中的第一个节点视为 Node01。
2、在第一个节点启动期间，集群设置向导便开始在控制台上运行。
| 输入以下命令以创建新集群： cluster setup | ::> cluster setup Welcome to the cluster setup wizard.
You can enter the following commands at any time: "help" or "?" - if you want to have a question clarified, "back" - if you want to change previously answered questions, and "exit" or "quit" - if you want to quit the cluster setup wizard. Any changes you made before quitting will be saved.
You can return to cluster setup at any time by typing "cluster setup". To accept a default or omit a question, do not enter a value.
Do you want to create a new cluster or join an existing cluster? {create, join}: create |
| 对单节点集群输入no，确认您正在配置多节点集群。 | Do you intend for this node to be used as a single node cluster? {yes, no} [no]: no |
| 如果您的集群要使用交换机 进行集群互连，请输入yes；如果该集群是一个双节点无交换机集群 (TNSC)，则输入no。 | Will the cluster network be configured to use network switches? [yes]: yes |
| 此时将显示系统默认设置。输入yes进行确认。 | System Defaults: Private cluster network ports [e0a,e0b]. Cluster port MTU values will be set to 9000. Cluster interface IP addresses will be automatically generated. Do you want to use these defaults? {yes, no} [yes]: yes |
| 输入以下各项以创建集群。 | Enter the cluster name: <<var_clustername>> Enter the cluster base license: <<var_cluster_license>> Network set up Creating cluster <<var_clustername>> Checking cluster applications .. Cluster <<var_clustername>> has been created Enter any additional licenses: <enter> |
| 输入“admin”帐户的密码。 | Enter the administrative (user "admin") password: <password> Retype the password: <password> |
| 输入要用于集群管理的网络详细信息。 | Enter the cluster management interface port [e0c]: <<var_clustermgmt_port>> Enter the cluster management interface IP address: <<var_clustermgmt_IP>> Enter the cluster management interface netmask: <<var_clustermgmt_netmask>> Enter the cluster management interface default gateway: <<var_clustermgmt_gateway>> A cluster management interface on port <<var_clustermgmt_port>> with IP address <<var_clustermgmt_IP>> has been created. You can use this address to connect to and manage the cluster. Enter the DNS domain name(s): <<var_global_domain_name>> Enter the comma seperated list of IP addresses for the nameservers: <<var_global_nameserver_IP>> DNS lookup for the admin vserver will use the <<var_global_domain_name>> domain. |
| 输入要用于节点管理的网络详细信息。 | Where is the controller located? []: <<var_install_floor_room>> Enter the node management interface port [e0c]: <<var_node01_mgmt_port>> Enter the node management interface IP address: <<var_node01_mgmt_IP>> Enter the node management interface netmask: <<var_node01_mgmt_netmask>> Enter the node management interface default gateway: <<var_node01_mgmt_gateway>> |
3、加入集群
在集群模式 ONTAP 中加入集群的前提条件
| 在第一个节点启动期间，集群设置向导便开始在控制台上运行。 cluster setup | ::> cluster setup Welcome to the cluster setup wizard.
You can enter the following commands at any time: "help" or "?" - if you want to have a question clarified, "back" - if you want to change previously answered questions, and "exit" or "quit" - if you want to quit the cluster setup wizard. Any changes you made before quitting will be saved.
You can return to cluster setup at any time by typing "cluster setup". To accept a default or omit a question, do not enter a value.
Do you want to create a new cluster or join an existing cluster? {create, join}:join |
| 输入以下命令以加入集群： | join |
| 此时将显示系统默认设置。输入yes进行确认。 | System Defaults: Private cluster network ports [e0c,e0e]. Cluster port MTU values will be set to 9000. Cluster interface IP addresses will be automatically generated. Do you want to use these defaults? {yes, no} [yes]: yes |
| 输入要加入的集群的名称。 | Enter the cluster you would like to join: <<var_clustername>> Joining cluster <<var_clustername>> Checking cluster applications .. This node has joined cluster <<var_clustername>> |
| 输入要用于节点管理的网络详细信息。 | Enter the node management interface port [e0c]: <<var_node01_mgmt_port>> |
四、存储aggr的规划
| Aggr Name | Controller | Device Type | Total | Data | Parity | Flash Pool | Snap Reserve | Raid Type /Size | Root (TiB) | Flash Pool (TiB) | Usable (TiB) |
|
| |||||||||||
|
| |||||||||||
|
| |||||||||||
|
| |||||||||||
应用规划
| SVM | Vol名称 | Vol大小 | 应用 | 备注 |
|
|
| |||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
五、检查硬件初检
| Node 检查 | node-1::> cluster show Node Health Eligibility --------------------- ------- node-1 true true node-2 true true 2 entries were displayed. |
| license add | node-1::>system license add xxxxxxxxxxxxxxxxxxxxxxxx node-1::> system license status show |
| 开启HA模式 | ::>cluster ha modify -configured false ::> cluster ha show |
| 硬件检查 | ::> system health status show ::> system health alert show ::> system health chassis show ::> system health config show ::> system health controller show ::> system health subsystem show |
6690
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
