关于Arduino&SSD1306OLED（IIC）显示的学习

1、 前期准备

1. arduino UNO开发板
2. OLED 显示屏
3. 导线若干
4. 取模软件zimoV2.2
   这里推荐一个在线图片取模软件
   http://tools.clz.me/

2、引脚接线

OLED 显示屏有四个引脚，分别是：
SDA(数据线) SCK(时钟线) VDD(3.3V) GND
在UNO开发板上I2C接口，SDA对应D4，SCK对应D5
在MEGA2560开发板上I2C接口,SDA对应D20, SCL对应D21

3、通信地址

背面图：

模块背面的IIC ADRESSSELECT表示该模块在IIC通信作为从机时的地址，当中间的脚用电阻和左边接起来时，地址为0x78，当和右边接起来时，地址为0x7A。

这款屏幕尺寸约为0.96英寸，由SSD1306驱动，驱动接口I2C，I2C地址(0x3c 默认/0x3d)。
不同型号有不同的通信地址，可通过程序查询：

#include <Wire.h>  
   
void setup(){  
  Wire.begin();  
  Serial.begin(9600);  
  Serial.println("\nI2C Scanner");  
}  
void loop(){  
  byte error, address;  
  int nDevices;  
  Serial.println("Scanning...");  
  nDevices = 0;  
  for (address = 1; address < 127; address++ ){  
    // The i2c_scanner uses the return value of  
    // the Write.endTransmisstion to see if  
    // a device did acknowledge to the address.  
    Wire.beginTransmission(address);  
    error = Wire.endTransmission();  
    if (error == 0){  
      Serial.print("I2C device found at address 0x");  
      if (address < 16)  
        Serial.print("0");  
      Serial.print(address, HEX);  
      Serial.println(" !");  
      nDevices++;  
    }else if (error == 4){  
      Serial.print("Unknow error at address 0x");  
      if (address < 16)  
        Serial.print("0");  
      Serial.println(address, HEX);  
    }  
  }  
  if (nDevices == 0)  
    Serial.println("No I2C devices found\n");  
  else  
    Serial.println("done\n");  
  delay(5000); // wait 5 seconds for next scan  
} 

上传到arduino板上，打开串口可查看地址

4、编程与程序解读

注：编程之前需要添加Adafruit_SSD1306和Adafruit_GFX这两个库文件

官方例程：

/*********************************************************************
This is an example for our Monochrome OLEDs based on SSD1306 drivers

  Pick one up today in the adafruit shop!
  ------> http://www.adafruit.com/category/63_98

This example is for a 128x64 size display using I2C to communicate
3 pins are required to interface (2 I2C and one reset)

Adafruit invests time and resources providing this open source code, 
please support Adafruit and open-source hardware by purchasing 
products from Adafruit!

Written by Limor Fried/Ladyada  for Adafruit Industries.  
BSD license, check license.txt for more information
All text above, and the splash screen must be included in any redistribution
*********************************************************************/

#include <Wire.h>
#include <Adafruit_GFX.h>
#include <Adafruit_SSD1306.h>

#define OLED_RESET 4
Adafruit_SSD1306 display(OLED_RESET);

#define NUMFLAKES 10
#define XPOS 0
#define YPOS 1
#define DELTAY 2


#define LOGO16_GLCD_HEIGHT 16 
#define LOGO16_GLCD_WIDTH  16 
static const unsigned char PROGMEM logo16_glcd_bmp[] =
{ B00000000, B11000000,
  B00000001, B11000000,
  B00000001, B11000000,
  B00000011, B11100000,
  B11110011, B11100000,
  B11111110, B11111000,
  B01111110, B11111111,
  B00110011, B10011111,
  B00011111, B11111100,
  B00001101, B01110000,
  B00011011, B10100000,
  B00111111, B11100000,
  B00111111, B11110000,
  B01111100, B11110000,
  B01110000, B01110000,
  B00000000, B00110000 };

#if (SSD1306_LCDHEIGHT != 64)
#error("Height incorrect, please fix Adafruit_SSD1306.h!");
#endif

void setup()   {                
  Serial.begin(9600);

  // by default, we'll generate the high voltage from the 3.3v line internally! (neat!)
  display.begin(SSD1306_SWITCHCAPVCC, 0x3D);  // initialize with the I2C addr 0x3D (for the 128x64)
  // init done
  
  display.display(); // show splashscreen
  delay(2000);
  display.clearDisplay();   // clears the screen and buffer

  // draw a single pixel
  display.drawPixel(10, 10, WHITE);
  display.display();
  delay(2000);
  display.clearDisplay();

  // draw many lines
  testdrawline();
  display.display();
  delay(2000);
  display.clearDisplay();

  // draw rectangles
  testdrawrect();
  display.display();
  delay(2000);
  display.clearDisplay();

  // draw multiple rectangles
  testfillrect();
  display.display();
  delay(2000);
  display.clearDisplay();

  // draw mulitple circles
  testdrawcircle();
  display.display();
  delay(2000);
  display.clearDisplay();

  // draw a white circle, 10 pixel radius
  display.fillCircle(display.width()/2, display.height()/2, 10, WHITE);
  display.display();
  delay(2000);
  display.clearDisplay();

  testdrawroundrect();
  delay(2000);
  display.clearDisplay();

  testfillroundrect();
  delay(2000);
  display.clearDisplay();

  testdrawtriangle();
  delay(2000);
  display.clearDisplay();
   
  testfilltriangle();
  delay(2000);
  display.clearDisplay();

  // draw the first ~12 characters in the font
  testdrawchar();
  display.display();
  delay(2000);
  display.clearDisplay();

  // draw scrolling text
  testscrolltext();
  delay(2000);
  display.clearDisplay();

  // text display tests
  display.setTextSize(1);
  display.setTextColor(WHITE);
  display.setCursor(0,0);
  display.println("Hello, world!");
  display.setTextColor(BLACK, WHITE); // 'inverted' text
  display.println(3.141592);
  display.setTextSize(2);
  display.setTextColor(WHITE);
  display.print("0x"); display.println(0xDEADBEEF, HEX);
  display.display();
  delay(2000);

  // miniature bitmap display
  display.clearDisplay();
  display.drawBitmap(30, 16,  logo16_glcd_bmp, 16, 16, 1);
  display.display();

  // invert the display
  display.invertDisplay(true);
  delay(1000); 
  display.invertDisplay(false);
  delay(1000); 

  // draw a bitmap icon and 'animate' movement
  testdrawbitmap(logo16_glcd_bmp, LOGO16_GLCD