【无标题】

/include/ "system-conf.dtsi"

#include <dt-bindings/gpio/gpio.h>

#include <dt-bindings/input/input.h>

#include <dt-bindings/media/xilinx-vip.h>

#include <dt-bindings/phy/phy.h>

/ {

model = "Alientek Navigator Zynq Development Board";

compatible = "xlnx,zynq-zc702", "xlnx,zynq-7000";

leds {

compatible = "gpio-leds";

gpio-led1 {

label = "led2";

gpios = <&gpio0 0 GPIO_ACTIVE_HIGH>;

default-state = "on";

};

gpio-led2 {

label = "led1";

gpios = <&gpio0 54 GPIO_ACTIVE_HIGH>;

linux,default-trigger = "heartbeat";

};

gpio-led3 {

label = "pl_led0";

gpios = <&axi_gpio_0 0 0 GPIO_ACTIVE_HIGH>;

default-state = "on";

};

gpio-led4 {

label = "pl_led1";

gpios = <&axi_gpio_0 1 0 GPIO_ACTIVE_HIGH>;

linux,default-trigger = "timer";

};

gpio-led5 {

label = "ps_led0";

gpios = <&gpio0 7 GPIO_ACTIVE_HIGH>;

default-state = "on";

};

gpio-led6 {

label = "ps_led1";

gpios = <&gpio0 8 GPIO_ACTIVE_HIGH>;

linux,default-trigger = "timer";

};

};

keys {

compatible = "gpio-keys";

autorepeat;

gpio-key1 {

label = "pl_key0";

gpios = <&gpio0 55 GPIO_ACTIVE_LOW>;

linux,code = <KEY_LEFT>;

gpio-key,wakeup;

autorepeat;

};

gpio-key2 {

label = "pl_key1";

gpios = <&gpio0 56 GPIO_ACTIVE_LOW>;

linux,code = <KEY_RIGHT>;

gpio-key,wakeup;

autorepeat;

};

gpio-key3 {

label = "ps_key1";

gpios = <&gpio0 12 GPIO_ACTIVE_LOW>;

linux,code = <KEY_UP>;

gpio-key,wakeup;

autorepeat;

};

gpio-key4 {

label = "ps_key2";

gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;

linux,code = <KEY_DOWN>;

gpio-key,wakeup;

autorepeat;

};

touch-key {

label = "touch_key";

gpios = <&gpio0 57 GPIO_ACTIVE_HIGH>;

linux,code = <KEY_ENTER>;

gpio-key,wakeup;

autorepeat;

};

};

beep {

compatible = "gpio-beeper";

gpios = <&gpio0 58 GPIO_ACTIVE_HIGH>;

};

usb_phy0: phy0@e0002000 {

compatible = "ulpi-phy";

#phy-cells = <0>;

reg = <0xe0002000 0x1000>;

view-port = <0x0170>;

drv-vbus;

};

};

&uart0 {

u-boot,dm-pre-reloc;

status = "okay";

};

&sdhci0 {

u-boot,dm-pre-reloc;

status = "okay";

};

&usb0 {

dr_mode = "otg";

usb-phy = <&usb_phy0>;

};

&qspi {

u-boot,dm-pre-reloc;

flash@0 { /* 16 MB */

compatible = "w25q256", "jedec,spi-nor";

reg = <0x0>;

spi-max-frequency = <50000000>;

#address-cells = <1>;

#size-cells = <1>;

partition@0x00000000 {

label = "boot";

reg = <0x00000000 0x00100000>;

};

partition@0x00100000 {

label = "bootenv";

reg = <0x00100000 0x00020000>;

};

partition@0x00120000 {

label = "bitstream";

reg = <0x00120000 0x00400000>;

};

partition@0x00520000 {

label = "device-tree";

reg = <0x00520000 0x00020000>;

};

partition@0x00540000 {

label = "kernel";

reg = <0x00540000 0x00500000>;

};

partition@0x00A40000 {

label = "space";

reg = <0x00A40000 0x00000000>;

};

};

};

&gem0 {

local-mac-address = [00 0a 35 00 8b 87];

phy-handle = <ðernet_phy>;

ethernet_phy: ethernet-phy@7 { /* yt8521 */

reg = <0x7>;

device_type = "ethernet-phy";

};

};

&gem1 {

local-mac-address = [00 0a 35 00 11 55];

phy-reset-gpio = <&gpio0 63 GPIO_ACTIVE_LOW>;

phy-reset-active-low;

phy-handle = <&pl_phy>;

pl_phy: pl_phy@4 {

reg = <0x4>;

device_type = "ethernet-phy";

};

};

&watchdog0 {

status = "okay";

reset-on-timeout; // Enable watchdog reset function

};

&adc {

status = "okay";

xlnx,channels {

#address-cells = <1>;

#size-cells = <0>;

channel@0 {

reg = <0>;

};

};

};

&i2c0 {

clock-frequency = <100000>;

eeprom@50 {

compatible = "atmel,24c64";

reg = <0x50>;

pagesize = <32>;

};

rtc@51 {

compatible = "nxp,pcf8563";

reg = <0x51>;

};

};