蓝桥杯单片机第十届

qq_51508750
已于 2022-02-10 21:55:40 修改
阅读量439
点赞数 1
文章标签：单片机
于 2022-02-10 21:55:01 首次发布
本文链接：https://blog.csdn.net/qq_51508750/article/details/122870097
版权
iic.c
#include<STC15F2K60S2.H>
#include "iic.h"
#include "intrins.h"

#define somenop {_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();_nop_();}    


#define SlaveAddrW 0xA0
#define SlaveAddrR 0xA1

//总线引脚定义
sbit SDA = P2^1;  /* 数据线 */
sbit SCL = P2^0;  /* 时钟线 */


//总线启动条件
void IIC_Start(void)
{
	SDA = 1;
	SCL = 1;
	somenop;
	SDA = 0;
	somenop;
	SCL = 0;	
}

//总线停止条件
void IIC_Stop(void)
{
	SDA = 0;
	SCL = 1;
	somenop;
	SDA = 1;
}

//等待应答
bit IIC_WaitAck(void)
{
	SDA = 1;
	somenop;
	SCL = 1;
	somenop;
	if(SDA)    
	{   
		SCL = 0;
		IIC_Stop();
		return 0;
	}
	else  
	{ 
		SCL = 0;
		return 1;
	}
}

//通过I2C总线发送数据
void IIC_SendByte(unsigned char byt)
{
	unsigned char i;
	for(i=0;i<8;i++)
	{   
		if(byt&0x80) 
		{	
			SDA = 1;
		}
		else 
		{
			SDA = 0;
		}
		somenop;
		SCL = 1;
		byt <<= 1;
		somenop;
		SCL = 0;
	}
}

//从I2C总线上接收数据
unsigned char IIC_RecByte(void)
{
	unsigned char da;
	unsigned char i;
	
	for(i=0;i<8;i++)
	{   
		SCL = 1;
		somenop;
		da <<= 1;
		if(SDA) 
		da |= 0x01;
		SCL = 0;
		somenop;
	}
	return da;
}
unsigned char AD_read(unsigned char add)
{
	unsigned char temp;
	
	IIC_Start();
	IIC_SendByte(0x90);
	IIC_WaitAck();
	IIC_SendByte(add);
	IIC_WaitAck();
	IIC_Stop();
	
	IIC_Start();
	IIC_SendByte(0x91);
	IIC_WaitAck();
	temp=IIC_RecByte();
	IIC_Stop();
	
	return temp;
}
void AD_Write(unsigned char dat)
{
IIC_Start();
IIC_SendByte(0x90);
IIC_WaitAck();
IIC_SendByte(0x40);
IIC_WaitAck();
IIC_SendByte(dat);
IIC_WaitAck();
IIC_Stop();}




iic.h
#ifndef _IIC_H
#define _IIC_H

//函数声明
void IIC_Start(void); 
void IIC_Stop(void);  
void IIC_Ack(bit ackbit); 
void IIC_SendByte(unsigned char byt); 
bit IIC_WaitAck(void);  
unsigned char IIC_RecByte(void); 
unsigned char AD_read(unsigned char add);
void AD_Write(unsigned char dat);
#endif

main.c
#include<STC15F2K60S2.H>
#include "iic.h"
#include "intrins.h"
#define uchar unsigned char
#define uint unsigned int
	uchar tab[]={0XC0,0XF9,0XA4,0XB0,0X99,0X92,0X82,0XF8,0X80,0X90,0XBF,0XFF,//0-11
	0X40,0X79,0X24,0X30,0X19,0X12,0X02,0X78,0X00,0X10,//12-21
	0x8e,0xc1};//22-23
	uchar fla=0;
	uint fan=0,t_flag=0,zheng_now=0,fan_now=0,zheng=0;
	uint Time=0,freq=0,intr=0;
uchar yi,er,san,si,wu,liu,qi,ba;
bit S4,S5,S6,S7;
	bit scan=0;
	uchar AD_out=1,out=0;
uint num;
uint AD=0;
	uchar scan1=0;
uchar led=1;
void Allinit(void);
void Delayms(int ms);
void Display1(uchar yi,uchar er);
void Display2(uchar san,uchar si);
void Display3(uchar wu,uchar liu);
void Display4(uchar qi,uchar ba);
void keyscan(void);
void DIG(void);
	void Timer2Init(void);
	void Timer0Init(void);
void main(void)
{
	Allinit();
 Timer2Init();
Timer0Init();
	
	while(1)
	{
if(intr==499)
{AD_read(0X03);

if(AD_out==2)
{AD_Write(out);}
else if(AD_out==1)
{AD_Write(102);}}
	DIG();
if(led==1)
{
if(fla==1){P2=0X80;P0=0XFF;P00=1;P01=0;
P02=1;
if(freq<1000){P03=1;}
else if((freq>=1000)&&(freq<5000)){P03=0;}
else if((freq>=5000)&&(freq<10000)){P03=1;}
else if(freq>10000){P03=0;}
if(AD_out==1){P04=1;}
else if(AD_out==2){P04=0;}
P05=1;P06=1;P07=1;}

else if(fla==0)
	{P2=0X80;P0=0XFF;P00=0;P01=1;
if(num<150){P02=1;}
else if((num>=150)&&(num<250)){P02=0;}
else if((num>=250)&&(num<350)){P02=1;}
else if(num>=350){P02=0;}
P03=1;
if(AD_out==1){P04=1;}
else if(AD_out==2){P04=0;}
P05=1;P06=1;P07=1;}
	}
		keyscan();
		Display1(yi,er);
		Display2(san,si);
		Display3(wu,liu);
		Display4(qi,ba);
	}
}
void keyscan(void)
{
	if(P30==0)
	{
		Delayms(5);
		if(P30==0)
		{
			if(scan1==0){scan1=1;
				P2=0XC0;//打开控制数码管位选的573
	P0=0XFF;//选中所有数码管
	P2=0XE0;//打开控制数码管段选的573
	P0=0XFF;//关闭所有的数码管
			}
   else if(scan1==1){scan1=0;}
		}
		while(!P30);
	}
	else 	if(P31==0)
	{
		Delayms(5);
		if(P31==0)
		{
			if(led==1){led=0;P2=0X80;P0=0XFF;}
			else if(led==0){led=1;}
		}
		while(!P31);
	}
	else 	if(P32==0)
	{
		Delayms(5);
		if(P32==0)
		{
			if(AD_out==1){AD_out=2;}
			else if(AD_out==2){AD_out=1;}
		}
		while(!P32);
	}
	else 	if(P33==0)
	{
		Delayms(5);
		if(P33==0)
		{
			if(fla==0){fla=1;}
			else if(fla==1){fla=0;}
		}
		while(!P33);
	}
}

void DIG(void)
{if(fla==0)
 {num=AD_read(0X03)*(1.96079);
	 yi=23;er=11;san=11;si=11;wu=11;liu=num/100+12;qi=num%100/10;ba=num%10;}
else if(fla==1)
{if(freq>=10000){yi=22;er=11;san=11;si=freq/10000;wu=freq%10000/1000;liu=freq%1000/100;qi=freq%100/10;ba=freq%10;}
 else if(freq>=1000){yi=22;er=11;san=11;si=11;wu=freq%10000/1000;liu=freq%1000/100;qi=freq%100/10;ba=freq%10;}
 else if(freq>=100){yi=22;er=11;san=11;si=11;wu=11;liu=freq%1000/100;qi=freq%100/10;ba=freq%10;}
 else if(freq>=10){yi=22;er=11;san=11;si=11;wu=11;liu=11;qi=freq%100/10;ba=freq%10;}}}
	void Timer0Init(void)
{
	AUXR |= 0x80;		//定时器时钟1T模式
	TMOD &= 0xF0;		//设置定时器模式
	TL0 = 0xC4;		//设置定时初值
	TH0 = 0xFF;		//设置定时初值
	TF0 = 0;		//清除TF0标志
//	TR0 = 1;		//定时器0开始计时
}
 void tm0() interrupt 1
 {if(P34==0)
	{
		fan++;
		if(t_flag==0)
		{
			t_flag=1;
			zheng_now=zheng;
			zheng=0;
		}
	}
	else if(P34==1)
	{
		zheng++;
		if(t_flag==1)
		{
			t_flag=0;
			fan_now=fan;
			fan=0;
		}
	}
  }
void Timer2Init(void)		//1毫秒@12.000MHz
{
	AUXR |= 0x04;		//定时器时钟1T模式
	T2L = 0x20;		//设置定时初值
	T2H = 0xD1;		//设置定时初值
	AUXR |= 0x10;		//定时器2开始计时
	IE2 |= 0x04;    //开定时器2中断
	EA=1;
}
void t2int() interrupt 12  
{
	intr++;
	if(intr==969)
	{
		TR0 = 1;ET0 = 1 ;
	}
	else if(intr==999)
	{
		intr=0;
		TR0 = 0;ET0 = 0 ;
		Time=(fan_now+zheng_now)*5;
		freq=1000000/Time;
	}}

void Display1(uchar yi,uchar er)
{if(scan1==0)
	{
	P2=0XC0;
	P0=0X01;
	P2=0XE0;
	P0=tab[yi];
	Delayms(1);
	
	P2=0XC0;
	P0=0X02;
	P2=0XE0;
	P0=tab[er];
	Delayms(1);
}}

void Display2(uchar san,uchar si)
{if(scan1==0)
	{
	P2=0XC0;
	P0=0X04;
	P2=0XE0;
	P0=tab[san];
	Delayms(1);
	
	P2=0XC0;
	P0=0X08;
	P2=0XE0;
	P0=tab[si];
	Delayms(1);
	}
}

void Display3(uchar wu,uchar liu)
{if(scan1==0)
	{
	P2=0XC0;
	P0=0X10;
	P2=0XE0;
	P0=tab[wu];
	Delayms(1);
	
	P2=0XC0;
	P0=0X20;
	P2=0XE0;
	P0=tab[liu];
	Delayms(1);
	}
}

void Display4(uchar qi,uchar ba)
{if(scan1==0)
	{
	P2=0XC0;
	P0=0X40;
	P2=0XE0;
	P0=tab[qi];
	Delayms(1);
	
	P2=0XC0;
	P0=0X80;
	P2=0XE0;
	P0=tab[ba];
	Delayms(1);
	}
}

void Allinit(void)
{
	P2=0XA0;//打开控制蜂鸣器的573
	P0=0X00;//关闭蜂鸣器继电器
	
	P2=0XC0;//打开控制数码管位选的573
	P0=0XFF;//选中所有数码管
	P2=0XE0;//打开控制数码管段选的573
	P0=0XFF;//关闭所有的数码管
	
	P2=0X80;//打开控制LED的573
	P0=0XFF;//关闭所有的LED
}

void Delayms(int ms)
{
	int i,j;
	for(i=0;i<ms;i++)
		for(j=845;j>0;j--);
}
记录.....功能全部可以实现，或许不是最优化的解法