TLC2543硬件SPI代码

void SPI1_Configuration(void)
{
	GPIO_InitTypeDef 	GPIO_InitStructure;
	SPI_InitTypeDef   	SPI_InitStructure;	   

	RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_SPI1 | RCC_APB2Periph_AFIO, ENABLE);	

	/* 初始化SCK、MISO、MOSI引脚 */
	GPIO_InitStructure.GPIO_Pin = AD_CLK_PIN | AD_SI_PIN | AD_SO_PIN;
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
	GPIO_Init(AD_PORT, &GPIO_InitStructure);
	GPIO_SetBits(AD_PORT,AD_CLK_PIN | AD_SI_PIN | AD_SO_PIN);;

	/* 初始化配置STM32 SPI1 */
	SPI_InitStructure.SPI_Direction=SPI_Direction_2Lines_FullDuplex;	//SPI设置为双线双向全双工
	SPI_InitStructure.SPI_Mode=SPI_Mode_Master;							//设置为主SPI
	SPI_InitStructure.SPI_DataSize=SPI_DataSize_16b;						//SPI发送接收16位帧结构   关键！！！
	SPI_InitStructure.SPI_CPOL=SPI_CPOL_Low;							//时钟悬空低
	SPI_InitStructure.SPI_CPHA=SPI_CPHA_1Edge;							//数据捕获于第1个时钟沿
	SPI_InitStructure.SPI_NSS=SPI_NSS_Soft;								//NSS由外部管脚管理
	SPI_InitStructure.SPI_BaudRatePrescaler=SPI_BaudRatePrescaler_32;	//波特率预分频值为32
	SPI_InitStructure.SPI_FirstBit=SPI_FirstBit_MSB;					//数据传输从MSB位开始
	SPI_InitStructure.SPI_CRCPolynomial=7;								//CRC多项式为7
	SPI_Init(SPI1,&SPI_InitStructure);									//根据SPI_InitStruct中指定的参数初始化外设SPI1寄存器

	SPI_Cmd(SPI1,ENABLE);	//STM32使能SPI1
}


u16 Read_TLC2543(u8 ch)
{
	u8 timeout;
	u16 chx,ADCdata;

	chx=ch<<12;
	chx|=0x0c00;
	AD_CS1=0;
	delay_us(10);
	while(SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_TXE)==RESET)
	{
		timeout++;
		if(timeout>200)
			return 0;	  
	}
  	SPI_I2S_SendData(SPI1,chx);    
	timeout=0;	
  	while(SPI_I2S_GetFlagStatus(SPI1, SPI_I2S_FLAG_RXNE)==RESET)
	{
		timeout++;
		if(timeout>200)
			return 0;	  
	}
 	ADCdata=SPI_I2S_ReceiveData(SPI1); 
  	delay_us(10); 
 	AD_CS1=1;
 	ADCdata>>=4;                                  
  	return ADCdata;
}

头文件

#ifndef __TLC2543_H
#define __TLC2543_H
#include "sys.h"

#define AD_CLK PAout(5)						
#define AD_CLK_PIN GPIO_Pin_5
#define AD_PORT GPIOA
#define AD_SI PAout(7)						
#define AD_SI_PIN GPIO_Pin_7
#define AD_SO PAout(6)						
#define AD_SO_PIN GPIO_Pin_6

#define AD_CS1 PAout(4)						
#define AD_CS1_PIN GPIO_Pin_4
#define AD_CS1_PORT GPIOA

#define AD_CS2 PCout(5)					 
#define AD_CS2_PIN GPIO_Pin_5		
#define AD_CS2_PORT GPIOC
			 
#define AD_DRDY1_PIN GPIO_Pin_4		
#define AD_DRDY1_PORT GPIOC

#define AD_DRDY2_PIN GPIO_Pin_0		
#define AD_DRDY2_PORT GPIOB

extern u8 AD_CH;
extern u16 Vadc[9];
extern u16 Aadc[9];
extern _Bool AD_DRDY1;
extern _Bool AD_DRDY2;

void TLC2543_GPIO_Configuration(void);
void TLC2543_NVIC_Configuration(void);
void SPI1_Configuration(void);
void TLC2543_Init(void);
u16 Read_TLC2543(u8 ch,u8 ad);
#endif