STM32F767 QSPI W25Q256 四线读 Quad SPI Lines模式 32位地址模式 内存映射模式

/* Private variables ---------------------------------------------------------*/

QSPI_HandleTypeDef hqspi;

/* USER CODE BEGIN PV */


/* USER CODE END PV */

/* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
static void MX_GPIO_Init(void);
static void MX_QUADSPI_Init(void);
/* USER CODE BEGIN PFP */

/* USER CODE END PFP */

/* Private user code ---------------------------------------------------------*/
/* USER CODE BEGIN 0 */

#define DATA_SIZE 10000
#define DATA_ADDR 400

uint8_t flag_tx_done;
uint8_t flag_rx_done;
uint8_t flag_cmd_done;

//uint8_t temp2[50] = {0};
uint8_t *temp3 = (uint8_t*)QSPI_BASE;

/* USER CODE END 0 */

/**
  * @brief  The application entry point.
  * @retval int
  */
int main(void)
{
  /* USER CODE BEGIN 1 */

  /* USER CODE END 1 */

  /* MCU Configuration--------------------------------------------------------*/

  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */
  HAL_Init();

  /* USER CODE BEGIN Init */

  /* USER CODE END Init */

  /* Configure the system clock */
  SystemClock_Config();

  /* USER CODE BEGIN SysInit */

  /* USER CODE END SysInit */

  /* Initialize all configured peripherals */
  MX_GPIO_Init();
  MX_QUADSPI_Init();
  /* USER CODE BEGIN 2 */
	
	//HAL_GPIO_WritePin(GPIOF, GPIO_PIN_6|GPIO_PIN_7, GPIO_PIN_SET);
	
	delay_init(216);
	delay_ms(500);
	
	QSPI_CommandTypeDef cmd;
	QSPI_MemoryMappedTypeDef cfg;
	
	cmd.Instruction = /*W25X_ReadData*/0xeb;
	cmd.Address = 0;
	cmd.AlternateBytes = 0xff;
	cmd.AddressSize = QSPI_ADDRESS_32_BITS;
	cmd.AlternateBytesSize = QSPI_ALTERNATE_BYTES_8_BITS;
	cmd.DummyCycles = 4;
	cmd.InstructionMode = QSPI_INSTRUCTION_1_LINE;
	cmd.AddressMode = QSPI_ADDRESS_4_LINES;
	cmd.AlternateByteMode = QSPI_ALTERNATE_BYTES_4_LINES;
	cmd.DataMode = QSPI_DATA_4_LINES;
	cmd.NbData = 0;
	cmd.DdrMode = QSPI_DDR_MODE_DISABLE;
	cmd.DdrHoldHalfCycle = QSPI_DDR_HHC_ANALOG_DELAY;
	cmd.SIOOMode = QSPI_SIOO_INST_EVERY_CMD;
	
	cfg.TimeOutActivation = QSPI_TIMEOUT_COUNTER_DISABLE;
	
	HAL_QSPI_MemoryMapped(&hqspi, &cmd, &cfg);
	
  /* USER CODE END 2 */

  /* Infinite loop */
  /* USER CODE BEGIN WHILE */
  while (1)
  {
    /* USER CODE END WHILE */

    /* USER CODE BEGIN 3 */

  }
  /* USER CODE END 3 */
}

/**
  * @brief QUADSPI Initialization Function
  * @param None
  * @retval None
  */
static void MX_QUADSPI_Init(void)
{

  /* USER CODE BEGIN QUADSPI_Init 0 */

  /* USER CODE END QUADSPI_Init 0 */

  /* USER CODE BEGIN QUADSPI_Init 1 */

  /* USER CODE END QUADSPI_Init 1 */
  /* QUADSPI parameter configuration*/
  hqspi.Instance = QUADSPI;
  hqspi.Init.ClockPrescaler = 2;
  hqspi.Init.FifoThreshold = 4;
  hqspi.Init.SampleShifting = QSPI_SAMPLE_SHIFTING_HALFCYCLE;
  hqspi.Init.FlashSize = 24;
  hqspi.Init.ChipSelectHighTime = QSPI_CS_HIGH_TIME_5_CYCLE;
  hqspi.Init.ClockMode = QSPI_CLOCK_MODE_0;
  hqspi.Init.FlashID = QSPI_FLASH_ID_1;
  hqspi.Init.DualFlash = QSPI_DUALFLASH_DISABLE;
  if (HAL_QSPI_Init(&hqspi) != HAL_OK)
  {
    Error_Handler();
  }
  /* USER CODE BEGIN QUADSPI_Init 2 */

  /* USER CODE END QUADSPI_Init 2 */

}

/**
  * @brief GPIO Initialization Function
  * @param None
  * @retval None
  */
static void MX_GPIO_Init(void)
{
  GPIO_InitTypeDef GPIO_InitStruct = {0};

  /* GPIO Ports Clock Enable */
  __HAL_RCC_GPIOC_CLK_ENABLE();
  __HAL_RCC_GPIOF_CLK_ENABLE();
  __HAL_RCC_GPIOH_CLK_ENABLE();
  __HAL_RCC_GPIOB_CLK_ENABLE();

  /*Configure GPIO pin Output Level */
  HAL_GPIO_WritePin(GPIOB, GPIO_PIN_1, GPIO_PIN_RESET);

  /*Configure GPIO pin : PB1 */
  GPIO_InitStruct.Pin = GPIO_PIN_1;
  GPIO_InitStruct.Mode = GPIO_MODE_OUTPUT_OD;
  GPIO_InitStruct.Pull = GPIO_NOPULL;
  GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;
  HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);

}

总结：
1、内存映射模式只能读不能写，即使地址对应的值为0xff也写不进去
2、QSPI映射起始地址为0x90000000

3、

4、