STM32F103C8T6 UART LOG

/* USER CODE BEGIN Header /
/*

---

• @file : main.c
• @brief : Main program body

---

• @attention

• © Copyright (c) 2020 STMicroelectronics.

• All rights reserved.
• This software component is licensed by ST under BSD 3-Clause license,
• the “License”; You may not use this file except in compliance with the
• License. You may obtain a copy of the License at:

•                    opensource.org/licenses/BSD-3-Clause
  

---

/
/ USER CODE END Header /
/ Includes ------------------------------------------------------------------/
#include “main.h”
#include <stdio.h>
/ Private includes ----------------------------------------------------------/
/ USER CODE BEGIN Includes */

/* USER CODE END Includes */

/* Private typedef -----------------------------------------------------------/
/ USER CODE BEGIN PTD */

/* USER CODE END PTD */

/* Private define ------------------------------------------------------------/
/ USER CODE BEGIN PD /
/ USER CODE END PD */

/* Private macro -------------------------------------------------------------/
/ USER CODE BEGIN PM */

/* USER CODE END PM */

/* Private variables ---------------------------------------------------------*/
UART_HandleTypeDef huart1;

/* USER CODE BEGIN PV */

/* USER CODE END PV */

/* Private function prototypes -----------------------------------------------*/
void SystemClock_Config(void);
static void MX_GPIO_Init(void);
static void MX_USART1_UART_Init(void);
#include <stdio.h>

/**

• @brief The application entry point.
• @retval int
  /
  int main(void)
  {
  / USER CODE BEGIN 1 */

/* USER CODE END 1 */

/* MCU Configuration--------------------------------------------------------*/

/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
HAL_Init();

/* USER CODE BEGIN Init */

/* USER CODE END Init */

/* Configure the system clock */
SystemClock_Config();

/* USER CODE BEGIN SysInit */

/* USER CODE END SysInit */

/* Initialize all configured peripherals /
MX_GPIO_Init();
MX_USART1_UART_Init();
/ USER CODE BEGIN 2 */

/* USER CODE END 2 */

/* Infinite loop /
/ USER CODE BEGIN WHILE */
char buf[256]={0};
int i=0;

while (1)
{
sprintf(buf,“fun:%s,line:%d %d \r\n”,func,LINE,i++);
HAL_UART_Transmit(&huart1,buf,strlen(buf),100);
HAL_Delay(100);
}
/* USER CODE END 3 */
}

/**

• @brief System Clock Configuration
• @retval None
  */
  void SystemClock_Config(void)
  {
  RCC_OscInitTypeDef RCC_OscInitStruct = {0};
  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};

/** Initializes the RCC Oscillators according to the specified parameters

• in the RCC_OscInitTypeDef structure.
  /
  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
  RCC_OscInitStruct.HSIState = RCC_HSI_ON;
  RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_NONE;
  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
  {
  Error_Handler();
  }
  /* Initializes the CPU, AHB and APB buses clocks
  */
  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
  |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_HSI;
  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;

if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_0) != HAL_OK)
{
Error_Handler();
}
}

/**

• @brief USART1 Initialization Function
• @param None
• @retval None
  */
  static void MX_USART1_UART_Init(void)
  {

/* USER CODE BEGIN USART1_Init 0 */

/* USER CODE END USART1_Init 0 */

/* USER CODE BEGIN USART1_Init 1 */

/* USER CODE END USART1_Init 1 /
huart1.Instance = USART1;
huart1.Init.BaudRate = 115200;
huart1.Init.WordLength = UART_WORDLENGTH_8B;
huart1.Init.StopBits = UART_STOPBITS_1;
huart1.Init.Parity = UART_PARITY_NONE;
huart1.Init.Mode = UART_MODE_TX_RX;
huart1.Init.HwFlowCtl = UART_HWCONTROL_NONE;
huart1.Init.OverSampling = UART_OVERSAMPLING_16;
if (HAL_UART_Init(&huart1) != HAL_OK)
{
Error_Handler();
}
/ USER CODE BEGIN USART1_Init 2 */

/* USER CODE END USART1_Init 2 */

}

/**

• @brief GPIO Initialization Function
• @param None
• @retval None
  */
  static void MX_GPIO_Init(void)
  {

/* GPIO Ports Clock Enable */
__HAL_RCC_GPIOA_CLK_ENABLE();

}

/* USER CODE BEGIN 4 */

/* USER CODE END 4 */

/**

• @brief This function is executed in case of error occurrence.
• @retval None
  /
  void Error_Handler(void)
  {
  / USER CODE BEGIN Error_Handler_Debug /
  / User can add his own implementation to report the HAL error return state */

/* USER CODE END Error_Handler_Debug */
}

#ifdef USE_FULL_ASSERT
/**

• @brief Reports the name of the source file and the source line number

•     where the assert_param error has occurred.
  

• @param file: pointer to the source file name
• @param line: assert_param error line source number
• @retval None
  */
  void assert_failed(uint8_t file, uint32_t line)
  {
  / USER CODE BEGIN 6 /
  / User can add his own implementation to report the file name and line number,
  tex: printf(“Wrong parameters value: file %s on line %d\r\n”, file, line) /
  / USER CODE END 6 /
  }
  #endif / USE_FULL_ASSERT */

/************************ © COPYRIGHT STMicroelectronics *END OF FILE/