设备树学习- -电容触摸屏驱动

首先,分析下 FT5406 的基本电路接口:
基本都是通用的接口,如 I2C 接口,INT,WAKE,RST。如图:


以上可知,我们在驱动中必须定义一个中断口,来启动接收触摸数据,一个gpio脚来复位FT5406。wake:主要靠cpu发送一个唤醒指令给FT5406。
查看tiny4412原理图

再次,需确认FT5406的从地址,以便于I2C访问得到。这个可以根据FT5406数据手册查找到.

可知从地址高位必须为:3,低位必须根据 i2ccon 设定的值来确定,这点很奇怪。
我这边找到的从地址为:0x38
i2ccon 暂时未找到出处,可以用 i2c tools 探测一下

/mnt # ./i2cdetect -y 1                                            
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f                
00:          -- -- -- -- -- -- -- -- -- -- -- -- --                
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --                
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --                
30: -- -- -- -- -- -- -- -- 38 -- -- -- -- -- -- --                
40: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --                
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --                
60: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- --                
70: -- -- -- -- -- -- -- -- 

基本的东西确认好后,剩下的就是根据FT5406数据手册上的指令,开始写驱动了。
在此之前,我们先了解下驱动如何实现电容屏的多点触摸,其实很简单,主要需要
触摸屏IC FT5406 能够捕获多点数据,这点电容屏基本多能支持到捕获2点以上,而FT5406 可以捕获5个触摸点,编写驱动时,只要去获取这几个点的数据,然后上报就行。格式如图:

解释:

02h : 捕获的触摸点个数
03h- 1eh :对应每个点的x,y坐标数值。
touch id 表示触点编号,对应于typeB的slot


驱动参考:Ft6236.c (drivers\input\touchscreen)

touch_demo{
    compatible = "tiny4412,touch_demo";
    interrupts = <6 0>;
        interrupt-parent = <&gpx1>;
        status = "okay";
};

&i2c_1{
        status = "okay";
        touch@38{
                compatible = "tiny4412,touch";
                reg = <0x38>;
        };
};

#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/i2c.h>
#include <linux/err.h>
#include <linux/regmap.h>
#include <linux/slab.h>
#include <linux/fs.h>
#include <asm/uaccess.h>
#include <linux/delay.h>
#include <linux/gpio/consumer.h>
#include <linux/input.h>
#include <linux/input/mt.h>
#include <linux/interrupt.h>
#include <linux/module.h>
#include <linux/property.h>
#include <linux/of_gpio.h>


#define uchar unsigned char

static void touch_read_handler(struct work_struct *work);
DECLARE_WORK(touch_read_work, touch_read_handler);


static struct i2c_client *touch_client;
static struct input_dev *touch_dev;
static int irq;


static void touch_read(unsigned char sAddr, unsigned char *buf, unsigned int len)
{
    struct i2c_msg msg[2];
    int i, ret;
    unsigned char address;
    for (i = 0; i < len; i++)
    {
        /* 先写入要读取的寄存器地址 */
        address = sAddr + i;
        msg[0].addr  = touch_client->addr;    /* 目的 */
        msg[0].buf   = &address;              /* 源 */
        msg[0].len   = 1;                     /* 地址=1 byte */
        msg[0].flags = 0;                     /* 表示写 */

        /* 然后启动读操作 */
        msg[1].addr  = touch_client->addr;    /* 源 */
        msg[1].buf   = &buf[i];               /* 目的 */
        msg[1].len   = 1;                     /* 数据=1 byte */
        msg[1].flags = I2C_M_RD;              /* 表示读 */
        ret = i2c_transfer(touch_client->adapter, msg, 2);
        if (ret < 0)
        {
            printk("i2c_transfer eror\n");
        }
        mdelay(10);
    }

}

static void touch_read_handler(struct work_struct *work)
{
    unsigned char buf[13];
    unsigned char touches, i, event, id;
    unsigned short x, y;
    bool act;
    /* read tp resister by i2c */
    touch_read(0x00, buf, 13);

    /* number of touch points */
    touches = buf[2] & 0x0f;
    //printk("point num %d\n", touches);

    if (touches > 2) {
        printk("%s touch read touches error\n",__func__);
        touches = 2;
    }

    for (i = 0; i < touches; i++) {
        y = ((buf[5 + i * 6] & 0x0f) << 8) | buf[6 + i * 6];
        x = ((buf[3 + i * 6] & 0x0f) << 8) | buf[4 + i * 6];
        //printk("%d point x:%08d y:%08d\n", i, x, y);
        event = buf[3 + i * 6] >> 6;    //event flags
        id = buf[5 + i * 6] >> 4;       //touch id
        //printk("event %d id %d\n", event, id);

        //down or contact
        act = (event == 0x00 || event == 0x02);

        input_mt_slot(touch_dev, id);
        input_mt_report_slot_state(touch_dev, MT_TOOL_FINGER, act);

        //if up return
        if (!act)
            continue;

        input_report_abs(touch_dev, ABS_MT_POSITION_X, x);
        input_report_abs(touch_dev, ABS_MT_POSITION_Y, y);  
    }

    input_mt_sync_frame(touch_dev);
    input_sync(touch_dev);

}

static irqreturn_t touch_isr(int irq, void *dev_id)
{
    schedule_work(&touch_read_work);

    return IRQ_HANDLED;
}

static int touch_probe(struct i2c_client *client,
                         const struct i2c_device_id *id)
{
    unsigned char buf;
    int ret;

    touch_client = client;
    printk("%s %s %d\n", __FILE__, __FUNCTION__, __LINE__);

    touch_read(0xa3, &buf, 1);
    printk("Chip vendor ID  %x\n", buf);

    touch_read(0xa6, &buf, 1);
    printk("Firmware ID %x\n", buf);

    touch_read(0xa8, &buf, 1);
    printk("CTPM Vendor ID %x\n", buf);

    touch_read(0x00, &buf, 1);
    printk("DEVIDE_MODE %x\n", buf);

    touch_read(0x80, &buf, 1);
    printk("ID_G_THGROUP. %x\n", buf);

    touch_read(0x88, &buf, 1);
    printk("ID_G_PERIODACTIVE. %x\n", buf);

    touch_dev = input_allocate_device();
    if (touch_dev == NULL)
    {
        printk("%s, allocate input device, error\n", __func__);
        return -1;
    }

    //告诉input能够支持哪些事件
    input_set_abs_params(touch_dev, ABS_MT_POSITION_X, 0, 800, 0, 0);
    input_set_abs_params(touch_dev, ABS_MT_POSITION_Y, 0, 480, 0, 0);
    ret = input_mt_init_slots(touch_dev, 2, INPUT_MT_DIRECT | INPUT_MT_DROP_UNUSED);
    if (ret)
    {
        printk("%s, input_mt_init_slots error\n", __func__);
        return ret;
    }
    touch_dev->name = "touch";
    touch_dev->id.bustype = BUS_I2C;
    touch_dev->dev.parent = &(touch_client)->dev;
    ret = input_register_device(touch_dev);
    if (ret)
    {
        printk("%s, register input device, error\n", __func__);
        return ret;
    }

    printk("irq is %d\n", irq); 

    ret = devm_request_threaded_irq(&touch_client->dev, irq, touch_isr, NULL, IRQF_TRIGGER_FALLING | IRQF_ONESHOT, "touch1", NULL);

    if (ret < 0)
    {
        printk("failed to request_irq %d\n", ret);
    }

    return 0;
}

static int touch_remove(struct i2c_client *client)
{

    return 0;
}

static const struct i2c_device_id touch_id_table[] =
{
    { "touch", 0 },
    {}
};


/* 1. 分配/设置i2c_driver */
static struct i2c_driver touch_driver =
{
    .driver = {
        .name   = "touch",
        .owner  = THIS_MODULE,
    },
    .probe      = touch_probe,
    .remove     = touch_remove,
    .id_table   = touch_id_table,
};


static int int_demo_remove(struct platform_device *pdev) {

    printk("%s enter.\n", __func__);

    return 0;
}

static int int_demo_probe(struct platform_device *pdev) {
    irq = platform_get_irq(pdev, 0);
    printk("int_demo_probe %d\n", irq);
    return 0;
}

static const struct of_device_id touch_demo_dt_ids[] = {
    { .compatible = "tiny4412,touch_demo", },
    {},
};
MODULE_DEVICE_TABLE(of, touch_demo_dt_ids);
static struct platform_driver touch_demo_driver = {
    .driver        = {
        .name      = "touch_demo",
        .of_match_table    = of_match_ptr(touch_demo_dt_ids),
    },
    .probe         = int_demo_probe,
    .remove        = int_demo_remove,
};


static int touch_drv_init(void)
{
    int ret;
    /* 1.注册平台设备驱动 */
    ret = platform_driver_register(&touch_demo_driver);
    if (ret)
        printk(KERN_ERR "int demo: probe failed: %d\n", ret);
    /* 2. 注册i2c_driver */
    i2c_add_driver(&touch_driver);

    return 0;
}

static void touch_drv_exit(void)
{
    i2c_del_driver(&touch_driver);
    platform_driver_unregister(&touch_demo_driver);
}


module_init(touch_drv_init);
module_exit(touch_drv_exit);
MODULE_LICENSE("GPL");
 

  • 1
    点赞
  • 4
    收藏
    觉得还不错? 一键收藏
  • 0
    评论

“相关推荐”对你有帮助么?

  • 非常没帮助
  • 没帮助
  • 一般
  • 有帮助
  • 非常有帮助
提交
评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值