手机ttl刷机linux,求助，TTl刷机遇到的问题

TTL出现以下内容然后就没有了，请问是什么原因？(如果不接TTL线能正常启动)波特率12800(波特率115200乱码更厉害)

猎豹截图20171214114518.png (43.25 KB, 下载次数: 0)

2017-12-14 11:44 上传

如果在启动过程中接上TTL线能出现以下内容(波特率115200)

[10:59:20.750]收←◆酈ooW藵丄th瀹k丄R93)\0

[10:59:20.890]收←◆峀inux version 2.6.31--LSDK-9.2.0_U11.14-svn1230 (root@xasoft77) (gcc version 4.3.3 (GCC) ) #2 Mon Nov 4 18:24:37 CST 2013

flash_size passed from bootloader = 8

arg 1: console=ttyS0,115200

arg 2: root=/dev/mtdblock2

arg 3: rootfstype=squashfs

arg 4: init=/sbin/init

arg 5: mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),5312k(rootfs),1408k(uImage),1024k(2ndfile),64k(ART),64k(mib0)

arg 6: mem=64M

CPU revision is: 0001974c (MIPS 74Kc)

ath_sys_frequency: cpu srif ddr srif cpu 560 ddr 450 ahb 225

Determined physical RAM map:

memory: 02000000 @ 00000000 (usable)

User-defined physical RAM map:

memory: 04000000 @ 00000000 (usable)

Initrd not found or empty - disabling initrd

Zone PFN ranges:

Normal   0x00000000 -> 0x00004000

Movable zone start PFN for each node

early_node_map[1] active PFN ranges

0: 0x00000000 -> 0x00004000

Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256

Kernel command line: console=ttyS0,115200 root=/dev/mtdblock2 rootfstype=squashfs init=/sbin/init mtdparts=ath-nor0:256k(u-boot),64k(u-boot-env),5312k(rootfs),1408k(uImage),1024k(2ndfile),64k(ART),64k(mib0) mem=64M

PID hash table entries: 256 (order: 8, 1024 bytes)

Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)

Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)

Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.

Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes

Writing ErrCtl register=00000000

Readback ErrCtl register=00000000

Memory: 46596k/65536k available (2456k kernel code, 18868k reserved, 1181k data, 160k init, 0k highmem)

NR_IRQS:128

plat_time_init: plat time init done

Calibrating delay loop... 279.55 BogoMIPS (lpj=559104)

Mount-cache hash table entries: 512

****************ALLOC***********************

Packet mem: 803c9dc0 (0xe00000 bytes)

********************************************

NET: Registered protocol family 16

netlink_init.

***** Warning *****: PCIe WLAN H/W not found !!!

bio: create slab at 0

SCSI subsystem initialized

usbcore: registered new interface driver usbfs

usbcore: registered new interface driver hub

usbcore: registered new device driver usb

NET: Registered protocol family 2

IP route cache hash table entries: 1024 (order: 0, 4096 bytes)

TCP established hash table entries: 2048 (order: 2, 16384 bytes)

TCP bind hash table entries: 2048 (order: 1, 8192 bytes)

TCP: Hash tables configured (established 2048 bind 2048)

TCP reno registered

NET: Registered protocol family 1

ATH GPIOC major 0

squashfs: version 4.0 (2009/01/31) Phillip Lougher

JFFS2 version 2.2 (ZLIB) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.

fuse init (API version 7.12)

msgmni has been set to 91

alg: No test for lzma (lzma-generic)

alg: No test for stdrng (krng)

io scheduler noop registered

io scheduler deadline registered (default)

led_init!

led_probe!

lct_led_init!

button_init

key_def_init

drivers/char/lct_button.c (key_def_init) GPIO_WPS_RST_KEY: 2

irq_num is 34,gpio is 2

Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled

serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A

console [ttyS0] enabled

brd: module loaded

tun: Universal TUN/TAP device driver, 1.6

tun: (C) 1999-2004 Max Krasnyansky

7 cmdlinepart partitions found on MTD device ath-nor0

Creating 7 MTD partitions on "ath-nor0":

0x000000000000-0x000000040000 : "u-boot"

0x000000040000-0x000000050000 : "u-boot-env"

0x000000050000-0x000000580000 : "rootfs"

0x000000580000-0x0000006e0000 : "uImage"

0x0000006e0000-0x0000007e0000 : "2ndfile"

0x0000007e0000-0x0000007f0000 : "ART"

0x0000007f0000-0x000000800000 : "mib0"

ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver

[10:59:21.281]收←◆Port Status 1c000004

ath-ehci ath-ehci.0: ATH EHCI

ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1

ehci_reset Intialize USB CONTROLLER in host mode: 13

ehci_reset Port Status 1c000000

ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000

ehci_reset Intialize USB CONTROLLER in host mode: 13

ehci_reset Port Status 1c000000

ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00

usb usb1: New USB device found, idVendor=1d6b, idProduct=0002

usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1

usb usb1: Product: ATH EHCI

usb usb1: Manufacturer: Linux 2.6.31--LSDK-9.2.0_U11.14-svn1230 ehci_hcd

usb usb1: SerialNumber: platform

usb usb1: configuration #1 chosen from 1 choice

hub 1-0:1.0: USB hub found

hub 1-0:1.0: 1 port detected

usbcore: registered new interface driver usblp

nf_conntrack version 0.5.0 (1024 buckets, 4096 max)

ip_tables: (C) 2000-2006 Netfilter Core Team

TCP cubic registered

NET: Registered protocol family 10

lo: Disabled Privacy Extensions

Mobile IPv6

ip6_tables: (C) 2000-2006 Netfilter Core Team

IPv6 over IPv4 tunneling driver

sit0: Disabled Privacy Extensions

ip6tnl0: Disabled Privacy Extensions

NET: Registered protocol family 17

802.1Q VLAN Support v1.8 Ben Greear

All bugs added by David S. Miller

arch/mips/atheros/gpio.c (ath_simple_config_init) JUMPSTART_GPIO: 16

ath_simple_config_init...725..

ath_simple_config_init...727..

athwdt_init: Registering WDT success

ath_otp_init: Registering OTP success

ath_clksw_init: Registering Clock Switch Interface success

VFS: Mounted root (squashfs filesystem) readonly on device 31:2.

Freeing unused kernel memory: 160k freed

[10:59:22.062]收←◆init started:  BusyBox v1.01 (2013.11.04-10:24+0000) multi-call binary

init started:  BusyBox v1.01 (2013.11.04-10:24+0000) multi-call binary

[10:59:22.109]收←◆Starting pid 165, console /dev/ttyS0: '/etc/rc.d/rcS'

[10:59:22.515]收←◆Starting the hotplug events dispatcher udevd

[10:59:23.062]收←◆Synthesizing initial hotplug events

[10:59:23.140]收←◆Jan  1 00:00:02 udevd[181]: main: the kernel does not support inotify, udevd can't monitor rules file changes

[10:59:23.437]收←◆ATHR_GMAC: Length per segment 1536

ATHR_GMAC: fifo cfg 3 01f00140

ATHR_GMAC: RX TASKLET - Pkts per Intr:16

ATHR_GMAC: Mac address for unit 0:bfff0000

ATHR_GMAC: ff:ff:ff:ff:ff:ff

[10:59:24.000]收←◆mac:0 Registering S27....

ATHR_GMAC: Max segments per packet :   1

ATHR_GMAC: Max tx descriptor count :   128

ATHR_GMAC: Max rx descriptor count :   128

ATHR_GMAC: Mac capability flags    :   2580

ATHR_GMAC: RX TASKLET - Pkts per Intr:16

ATHR_GMAC: Mac address for unit 1:bfff0006

ATHR_GMAC: ff:ff:ff:ff:ff:ff

[10:59:24.578]收←◆mac:1 Registering S27....

ATHR_GMAC: Max segments per packet :   1

ATHR_GMAC: Max tx descriptor count :   128

ATHR_GMAC: Max rx descriptor count :   128

ATHR_GMAC: Mac capability flags    :   2D80

[10:59:24.718]收←◆Initializing USB Mass Storage driver...

usbcore: registered new interface driver usb-storage

USB Mass Storage support registered.

[10:59:24.828]收←◆usbcore: registered new interface driver cdc_ether

[10:59:24.906]收←◆usbcore: registered new interface driver usbserial

usbserial: USB Serial Driver core

[10:59:24.953]收←◆USB Serial support registered for GSM modem (1-port)

usbcore: registered new interface driver option

option: v0.7.2:USB Driver for GSM modems

[10:59:25.062]收←◆usbcore: registered new interface driver lc_ether

SIOCGIFFLAGS: No such device

tar: /sbin/debug.tgz: No such file or directory

**** drop_caches_sysctl_handler: all done timer added ...****

[10:59:25.156]收←◆/etc/rc.d/rcS: 98: openvirtual**: not found

[10:59:25.515]收←◆done

Starting pid 31

[10:59:26.531]收←◆

(none) mips #2 Mon Nov 4 18:24:37 CST 2013 (none)

(none) login:

[10:59:32.343]收←◆asf: module license 'Proprietary' taints kernel.

Disabling lock debugging due to kernel taint

[10:59:33.421]收←◆ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, 11D)

[10:59:33.578]收←◆usb 1-1: new high speed USB device using ath-ehci and address 2

[10:59:33.718]收←◆usb 1-1: New USB device found, idVendor=1c9e, idProduct=9b05

usb 1-1: New USB device strings: Mfr=2, Product=3, SerialNumber=4

usb 1-1: Product: USB Modem

usb 1-1: Manufacturer: USB Modem

usb 1-1: configuration #1 chosen from 1 choice

option 1-1:1.0: GSM modem (1-port) converter detected

usb 1-1: GSM modem (1-port) converter now attached to ttyUSB0

option 1-1:1.1: GSM modem (1-port) converter detected

usb 1-1: GSM modem (1-port) converter now attached to ttyUSB1

option 1-1:1.2: GSM modem (1-port) converter detected

usb 1-1: GSM modem (1-port) converter now attached to ttyUSB2

option 1-1:1.3: GSM modem (1-port) converter detected

usb 1-1: GSM modem (1-port) converter now attached to ttyUSB3

[10:59:33.937]收←◆ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved

[10:59:34.859]收←◆device dummy0 entered promiscuous mode

[10:59:34.890]收←◆ath_dfs: Version 2.0.0

Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved

[10:59:34.937]收←◆br0: port 1(dummy0) entering forwarding state

[10:59:35.015]收←◆device eth0 entered promiscuous mode

athr_gmac_ring_alloc Allocated 2048 at 0x82d1e000

athr_gmac_ring_alloc Allocated 2048 at 0x82dd5800

[10:59:35.328]收←◆WASP ----> S27 PHY MDIO

Setting Drop CRC Errors, Pause Frames and Length Error frames

Setting PHY...

[10:59:38.937]收←◆ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved

[10:59:39.968]收←◆ath_ahb: 9.2.0_U11.14 (Atheros/multi-bss)

__ath_attach: Set global_scn[0]

ACBKMinfree = 48

ACBEMinfree = 32

ACVIMinfree = 16

ACVOMinfree = 0

CABMinfree = 48

UAPSDMinfree = 0

Wasp Enterprise mode: 0x00000000

Restoring Cal data from Flash

Using Cal data from Flash 0x9f7e0000

dfs_attach: use DFS enhancements

DFS min filter rssiThresh = 18

DFS max pulse dur = 151 ticks

ath_get_caps[5184] rx chainmask mismatch actual 3 sc_chainmak 0

ath_get_caps[5159] tx chainmask mismatch actual 3 sc_chainmak 0

ADDRCONF(NETDEV_UP): eth0: link is not ready

SC Callback Registration for wifi0

wifi0: Atheros 9340: mem=0xb8100000, irq=2

ath_pci: 9.2.0_U11.14 (Atheros/multi-bss)

[10:59:40.250]收←◆device eth1 entered promiscuous mode

athr_gmac_ring_alloc Allocated 2048 at 0x83b04000

athr_gmac_ring_alloc Allocated 2048 at 0x82dd7800

[10:59:40.562]收←◆WASP ----> S27 PHY MDIO

ATHRS27: resetting s27

[10:59:40.671]收←◆ATHRS27: s27 reset done

Setting Drop CRC Errors, Pause Frames and Length Error frames

Setting PHY...

[10:59:41.718]收←◆ADDRCONF(NETDEV_UP): eth1: link is not ready

[10:59:42.031]收←◆to start lc_debut_ctl thread!

[10:59:42.140]收←◆wlan_vap_create : enter. devhandle=0x82df82c0, opmode=IEEE80211_M_HOSTAP, flags=0x1

wlan_vap_create : exit. devhandle=0x82df82c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.

wlan_vap_create : enter. devhandle=0x82df82c0, opmode=IEEE80211_M_HOSTAP, flags=0x1

wlan_vap_create : exit. devhandle=0x82df82c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.

[10:59:42.234]收←◆wlan_vap_create : enter. devhandle=0x82df82c0, opmode=IEEE80211_M_HOSTAP, flags=0x1

wlan_vap_create : exit. devhandle=0x82df82c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.

[10:59:42.296]收←◆wlan_vap_create : enter. devhandle=0x82df82c0, opmode=IEEE80211_M_HOSTAP, flags=0x1

wlan_vap_create : exit. devhandle=0x82df82c0, opmode=IEEE80211_M_HOSTAP, flags=0x1.

[10:59:45.265]收←◆lct_led_open!

[10:59:45.906]收←◆dfs_init_radar_filters: Unknown dfs domain 0

[10:59:46.015]收←◆Setting Max Stations:32

[10:59:46.734]收←◆ ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1

DEVICE IS DOWN ifname=ath0

[10:59:47.125]收←◆ DEVICE IS DOWN ifname=ath0

[10:59:53.781]收←◆device ath0 entered promiscuous mode

br0: port 4(ath0) entering forwarding state

[10:59:53.890]收←◆ADDRCONF(NETDEV_UP): wan0: link is not ready

ifr.ifr_name = wan0

[10:59:54.484]收←◆ndis open exit.

ndis_get_lib_version:get version=1.5