lj245a引脚功能图_输出PWM波形，输出不稳定，正常输出是乱波，用力轻压LJ245A芯片输出就正常了...

void TIM1_PWM_Init(u16 arr ,u16 psc)

{

GPIO_InitTypeDef GPIO_InitStructure;

TIM_TimeBaseInitTypeDef  TIM_TimeBaseStructure;

TIM_OCInitTypeDef  TIM_OCInitStructure;

RCC_APB2PeriphClockCmd(RCC_APB2Periph_TIM1, ENABLE);//

//RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOC  , ENABLE);  //使能GPIO外设时钟使能

RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA  , ENABLE);  //使能GPIO外设时钟使能

//设置该引脚为复用输出功能,输出TIM1 CH1的PWM脉冲波形

GPIO_InitStructure.GPIO_Pin = GPIO_Pin_8; //TIM_CH1

//GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;

GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;  //复用推挽输出

GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;

GPIO_Init(GPIOA, &GPIO_InitStructure);

//GPIO_Init(GPIOC, &GPIO_InitStructure);

TIM_TimeBaseStructure.TIM_Period = arr; //设置在下一个更新事件装入活动的自动重装载寄存器周期的值         80K

TIM_TimeBaseStructure.TIM_Prescaler =psc; //设置用来作为TIMx时钟频率除数的预分频值  不分频

TIM_TimeBaseStructure.TIM_ClockDivision = 0; //设置时钟分割:TDTS = Tck_tim

TIM_TimeBaseStructure.TIM_CounterMode = TIM_CounterMode_Up;  //TIM向上计数模式

TIM_TimeBaseInit(TIM1, &TIM_TimeBaseStructure); //根据TIM_TimeBaseInitStruct中指定的参数初始化TIMx的时间基数单位

TIM_OCInitStructure.TIM_OCMode = TIM_OCMode_PWM2; //选择定时器模式:TIM脉冲宽度调制模式2

TIM_OCInitStructure.TIM_OutputState = TIM_OutputState_Enable; //比较输出使能

TIM_OCInitStructure.TIM_Pulse = 0; //设置待装入捕获比较寄存器的脉冲值

TIM_OCInitStructure.TIM_OCPolarity = TIM_OCPolarity_High; //输出极性:TIM输出比较极性高

TIM_OC1Init(TIM1, &TIM_OCInitStructure);  //根据TIM_OCInitStruct中指定的参数初始化外设TIMx

TIM_CtrlPWMOutputs(TIM1,ENABLE);        //MOE 主输出使能

TIM_OC1PreloadConfig(TIM1, TIM_OCPreload_Enable);  //CH1预装载使能

TIM_ARRPreloadConfig(TIM1, ENABLE); //使能TIMx在ARR上的预装载寄存器

TIM_Cmd(TIM1, ENABLE);  //使能TIM1

}

void TIM_SetCompare1(TIM_TypeDef* TIMx, uint16_t Compare1)

{

/* Check the parameters */

assert_param(IS_TIM_LIST8_PERIPH(TIMx));

/* Set the Capture Compare1 Register value */

TIMx->CCR1 = Compare1;//源程序

}