网卡绑定技术linux c,使用bonding技术实现双网卡绑定提高网卡性能

使用bonding技术实现双网卡绑定

在Linux系统中使用bonding技术，可以将两块网卡绑定为一个对外IP使用，以达到高可用或负载均衡的目的。以下简要介绍该技术的使用。

1.安装两块网卡

在linux系统下将两块网卡配置好，使其均能独立工作。可能会碰到驱动问题，自己想办法解决吧，无非是在内核配置里找或者找第三方的。

网卡不一定要一个型号，我用的一块是独立的，一块是集成的，也没什么问题。

2.编译内核

在内核中添加bonding的支持。

在原码目录下make menuconfig

选上device drivers -> network device support -> bonding driver support

一般来说2.4以上默认是选上的

3.bonding配置

------------------------------------------

This section applies to distros using a version of initscripts with bonding support, for example, Red Hat Linux 9 or Red Hat Enterprise Linux version 3 or 4.  On these systems, the network

initialization scripts have some knowledge of bonding, and can be configured to control bonding devices.

These distros will not automatically load the network adapter driver unless the ethX device is configured with an IP address. Because of this constraint, users must manually configure a

network-script file for all physical adapters that will be members of a bondX link.  Network script files are located in the directory:

/etc/sysconfig/network-scripts

The file name must be prefixed with "ifcfg-eth" and suffixed with the adapter's physical adapter number.  For example, the script for eth0 would be named /etc/sysconfig/network-scripts/ifcfg-eth0.Place the following text in the file:

DEVICE=eth0

USERCTL=no

ONBOOT=yes

MASTER=bond0

SLAVE=yes

BOOTPROTO=none

The DEVICE= line will be different for every ethX device and must correspond with the name of the file, i.e., ifcfg-eth1 must have a device line of DEVICE=eth1.  The setting of the MASTER= line will also depend on the final bonding interface name chosen for your bond. As with other network devices, these typically start at 0, and go up one for each device, i.e., the first bonding instance is bond0, the second is bond1, and so on.

Next, create a bond network script.  The file name for this script will be /etc/sysconfig/network-scripts/ifcfg-bondX where X is the number of the bond.  For bond0 the file is named "ifcfg-bond0",

for bond1 it is named "ifcfg-bond1", and so on.  Within that file, place the following text:

DEVICE=bond0

IPADDR=192.168.1.1

NETMASK=255.255.255.0

NETWORK=192.168.1.0

BROADCAST=192.168.1.255

ONBOOT=yes

BOOTPROTO=none

USERCTL=no

Be sure to change the networking specific lines (IPADDR, NETMASK, NETWORK and BROADCAST) to match your network configuration.

Finally, it is necessary to edit /etc/modules.conf (or /etc/modprobe.conf, depending upon your distro) to load the bonding module with your desired options when the bond0 interface is brought

up.  The following lines in /etc/modules.conf (or modprobe.conf) will load the bonding module, and select its options:

alias bond0 bonding

options bond0 mode=balance-alb miimon=100

Replace the sample parameters with the appropriate set of

options for your configuration.

Finally run "/etc/rc.d/init.d/network restart" as root.  This will restart the networking subsystem and your bond link should be now up and running.

下面是具体配置实例

vi /etc/sysconfig/network-scripts/ifcfg-bond0

DEVICE=bond0

NETWORK=192.168.0.0

IPADDR=192.168.0.111

NETMASK=255.255.255.0

BROADCAST=192.168.0.255

ONBOOT=yes

BOOTPROTO=none

USERCTL=no

vi /etc/sysconfig/network-scripts/ifcfg-eth0

DEVICE=eth0

USERCTL=no

ONBOOT=yes

MASTER=bond0

SLAVE=yes

BOOTPROTO=none

vi /etc/sysconfig/network-scripts/ifcfg-eth1

DEVICE=eth1

USERCTL=no

ONBOOT=yes

MASTER=bond0

SLAVE=yes

BOOTPROTO=none

vi /etc/modprobe.conf

加入两行

alias bond0 bonding

options bond0 miimon=100 mode=1

参数miimon是链路监测。miimon=100，表示系统每100ms监测一次链路连接状态，如果有一条线路不通就

转入另一条线路。

参数mode表示工作模式。

mode=0表示load balancing两块网卡同时工作，提供负载均衡。

mode=1表示fault-tolerance提供冗余功能，工作方式是主备的工作方式,提供高可用。

配置完毕后重启机器，启动过程中show details可以看到bonding启动成功。

4.察看bonding运行状态

[root@localhost /]# ifconfig

bond0     Link encap:Ethernet  HWaddr 00:1D:60:99:8C:EB

inet addr:192.168.0.111  Bcast:192.168.0.255  Mask:255.255.255.0

UP BROADCAST RUNNING MASTER MULTICAST  MTU:1500  Metric:1

RX packets:2805 errors:0 dropped:0 overruns:0 frame:0

TX packets:2006 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:0

RX bytes:281846 (275.2 KiB)  TX bytes:481206 (469.9 KiB)

eth0      Link encap:Ethernet  HWaddr 00:1D:60:99:8C:EB

UP BROADCAST RUNNING SLAVE MULTICAST  MTU:1500  Metric:1

RX packets:2302 errors:0 dropped:0 overruns:0 frame:0

TX packets:2014 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:1000

RX bytes:234137 (228.6 KiB)  TX bytes:482422 (471.1 KiB)

Interrupt:17 Base address:0xd400

eth1      Link encap:Ethernet  HWaddr 00:1D:60:99:8C:EB

UP BROADCAST RUNNING SLAVE MULTICAST  MTU:1500  Metric:1

RX packets:506 errors:0 dropped:0 overruns:0 frame:0

TX packets:0 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:1000

RX bytes:47889 (46.7 KiB)  TX bytes:0 (0.0 b)

Interrupt:21 Base address:0x4c00

lo        Link encap

ocal Loopback  

inet addr:127.0.0.1  Mask:255.0.0.0

UP LOOPBACK RUNNING  MTU:16436  Metric:1

RX packets:2640 errors:0 dropped:0 overruns:0 frame:0

TX packets:2640 errors:0 dropped:0 overruns:0 carrier:0

collisions:0 txqueuelen:0

RX bytes:4668416 (4.4 MiB)  TX bytes:4668416 (4.4 MiB)

[root@localhost /]# cat /proc/net/bonding/bond0

Ethernet Channel Bonding Driver: v3.1.3 (June 13, 2007)

Bonding Mode: fault-tolerance (active-backup)

Primary Slave: None

Currently Active Slave: eth0

MII Status: up

MII Polling Interval (ms): 100

Up Delay (ms): 0

Down Delay (ms): 0

Slave Interface: eth0

MII Status: up

Link Failure Count: 0

Permanent HW addr: 00:1d:60:99:8c:eb

Slave Interface: eth1

MII Status: up

Link Failure Count: 0

Permanent HW addr: 00:05:5d:74:2a:81

任意拔掉一条网线试试，看工作是否正常吗，/proc中有什么变化