android dts配置_[RK3288][Android6.0] WiFi的dts配置说明(AP6335)

Platform: Rockchip

OS: Android 6.0

Kernel: 3.10.92

使用的是AP6335, 硬件上用的是SDIO0.

原理图：

配置文件:

电源部分:

wireless-wlan {

compatible = "wlan-platdata";

/* wifi_chip_type - wifi chip define * ap6210, ap6330, ap6335 * rtl8188eu, rtl8723bs, rtl8723bu * esp8089 */

wifi_chip_type = "ap6335";

sdio_vref = <1800>; //1800mv or 3300mv

//keep_wifi_power_on;

//power_ctrl_by_pmu;

power_pmu_regulator = "act_ldo3";

power_pmu_enable_level = <1>; //1->HIGH, 0->LOW

//vref_ctrl_enable;

//vref_ctrl_gpio = ;

vref_pmu_regulator = "act_ldo3";

vref_pmu_enable_level = <1>; //1->HIGH, 0->LOW

WIFI,poweren_gpio = ;

WIFI,host_wake_irq = ;

//WIFI,reset_gpio = ;

status = "okay";

};

compatible = "wlan-platdata";

和rfkill-wlan.c电源驱动匹配

wifi_chip_type = "ap6335";

用它来判断使用哪个硬件模块，加载对应的wifi驱动，配置。

sdio_vref = <1800>; //1800mv or 3300mv

wifi模组的IO电压，设置错误会导致Wifi通信异常引起WiFi打不开或者工作不稳定问题。

keep_wifi_power_on;

默认关闭，打开后表示开机过程后就直接上电，并且一直保持上电状态，后续的电源操作会失效。

有些WiFi模组可能是WiFi和BT共用电源，这时需要一直保持上电状态。

power_ctrl_by_pmu;

表示WiFi的电源是否直接通过PMU控制，一般都是用GPIO控制，默认是关闭的。

power_pmu_regulator = "act_ldo3";

power_pmu_enable_level = <1>; //1->HIGH, 0->LOW

PMU输出口以及有效电平

vref_ctrl_enable;

在模组不工作(模组上的所有功能芯片都不工作)的情况下切断 IO参考电压输出,以此来降低一定的系统功耗。这个是可选配置并非所有硬件都支持,也不是所有WiFi模组都支持。

WIFI,poweren_gpio = ;

gpio控制WiFi Power

WIFI,host_wake_irq = ;

WiFi中断脚的配置,某些WiFi模组没有这个脚可以不用配置，AP6335需要配置。

SDIO部分：

&sdio {

clock-frequency = <50000000>;

clock-freq-min-max = <200000 50000000>;

supports-highspeed;

supports-sdio;

ignore-pm-notify;

keep-power-in-suspend;

//cap-sdio-irq;

status = "okay";

};

属性说明见

kernel/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt

clock-frequency: Stable clk freq for data transfer

clock-freq-min-max: Host issue slave devices for timing supportted ranges from this clk gap

supports-highspeed: Indicate if this controller support highspeed mode or not

supports-emmc: Indicate this controller works as emmc

supports-sd: Indicate this controller works as sd/mmc card

supports-sdio: Indicate this controller works as sdio function(card)

ignore-pm-notify: Indicate this controller will ignore pm notify

keep-power-in-suspend: Indicate this controller should keep power in system suspend

参考：

kernel/Documentation/devicetree/bindings/mmc/rockchip-dw-mshc.txt RK 3.10版本Kernel WiFi&BT_开发配置参考说明_for_Android5.0.pdf