linux go to,linux boot-go_to_protected_mode

/*

* Prepare the machine for transition to protected mode.

* 从实模式向保护模式跳转

* 文档:

* /arch/x86/include/asm/segment.h 【1】

* arch/x86/boot/pm.c【2】本文

* arch/x86/boot/a20.c【3】

*/

#include "boot.h"

#include

/*

* Invoke the realmode switch hook if present; otherwise

* disable all interrupts.

*

* boot loader hooks

* 当加载器运行的环境不能布置标准内存布局时,会用到加载器hooks。这种hooks尽量不要用。

* realmode_swtch:在转到保护模式前最后时刻执行,它是16位的(默认的例程是用来禁用NMI,

* 不可屏蔽中断)。

* code32_start : 这个字段可被用作hook,在转到保护模式后第一时刻执行,并且是32位的,

* 它的执行在内核解压前。实模式开始偏移512处是内核的开始。此时ds=es=ss=实模式代码加

* 载地址。推荐是fs=gs=ds=es=ss。一般情况下加载器会将它指向正常的、被压缩内核代码处。

*/

static inline void io_delay(void)

{

//boot.h:向0x80端口写al值来消耗时间

const u16 DELAY_PORT = 0x80;

asm volatile("outb %%al,%0" : : "dN" (DELAY_PORT));

}

static void realmode_switch_hook(void)

{

/*

* 调用hook,一般hook是不会设置的,所以走else流程

* 向0x70商品写0x80关NMI

*/

if (boot_params.hdr.realmode_swtch) {

asm volatile("lcallw *%0"

: : "m" (boot_params.hdr.realmode_swtch)

: "eax", "ebx", "ecx", "edx");

} else {

asm volatile("cli");

outb(0x80, 0x70); /* Disable NMI */

io_delay();

}

}

/*

* Disable all interrupts at the legacy PIC.

* PIC相关

* 端口范围:0x20-0x3f 8259 可编程中断控制器1

* 端口范围:0xa0-0xbf 8259 可编程中断控制器2

*

*/

static void mask_all_interrupts(void)

{

outb(0xff, 0xa1); /* Mask all interrupts on the secondary PIC */

io_delay();

outb(0xfb, 0x21); /* Mask all but cascade on the primary PIC */

io_delay();

}

/*

* Reset IGNNE# if asserted in the FPU.

* 端口范围:0x0f0-0x0ff 数学协处理器访问端口

*/

static void reset_coprocessor(void)

{

outb(0, 0xf0);

io_delay();

outb(0, 0xf1);

io_delay();

}

/*

* Set up the GDT

*/

struct gdt_ptr {

u16 len;// 0-15:GDT Lmit 大小

u32 ptr;//16-47:Base address 基址

} __attribute__((packed));

/*

* 启动时使用的gdt

* 仅设置了3项cs,ds,tss,代码段cs和数据段ds的段基址都设置为0

* 任务状态段段基址设置为4096

* 由文档【1】中可知:

*GDT_ENTRY_BOOT_CS=2

*GDT_ENTRY_BOOT_DS=3

*GDT_ENTRY_BOOT_TSS=4

* 这些值表示在表中的索引,分别处于临时gdt的索引2、3、4项

* 分别有__BOOT_CS=16,__BOOT_DS=24,__BOOT_TSS=32等

* 段选择子与段描述符对应

*/

static void setup_gdt(void)

{

/* There are machines which are known to not boot with the GDT

being 8-byte unaligned. Intel recommends 16 byte alignment. */

static const u64 boot_gdt[] __attribute__((aligned(16))) = {

/* CS: code, read/execute, 4 GB, base 0 */

[GDT_ENTRY_BOOT_CS] = GDT_ENTRY(0xc09b, 0, 0xfffff),

/* DS: data, read/write, 4 GB, base 0 */

[GDT_ENTRY_BOOT_DS] = GDT_ENTRY(0xc093, 0, 0xfffff),

/* TSS: 32-bit tss, 104 bytes, base 4096 */

/* We only have a TSS here to keep Intel VT happy;

we don't actually use it for anything. */

[GDT_ENTRY_BOOT_TSS] = GDT_ENTRY(0x0089, 4096, 103),

};

/* Xen HVM incorrectly stores a pointer to the gdt_ptr, instead

of the gdt_ptr contents. Thus, make it static so it will

stay in memory, at least long enough that we switch to the

proper kernel GDT. */

static struct gdt_ptr gdt;

gdt.len = sizeof(boot_gdt)-1;

gdt.ptr = (u32)&boot_gdt + (ds() << 4);

//通过lgdtl将48位的gdt放入gdtr寄存器

asm volatile("lgdtl %0" : : "m" (gdt));

}

/*

* Set up the IDT

* 中断描述符表初始化为0,先不使用

*/

static void setup_idt(void)

{

static const struct gdt_ptr null_idt = {0, 0};

asm volatile("lidtl %0" : : "m" (null_idt));

}

/*

* Actual invocation sequence

* 这个函数是从boot/main()跳过来执行的,它是pm.c中最主要的函数,它控制着保护模式

* 相关函数的调用顺序。它的主要工作有:

* 1.在离开实模式的最后时刻调用加载器hook

* 2.打开A20Gate

* 3.重置数学协处理器

* 4.屏蔽所有中断

* 5.设置idt

* 6.设置gdt

* 7.执行protected_mode_jump(code32_start hook)

* 对于code32_start(document/x86/boot.txt),前面说过,它也能作为加载器hook,只是它是在进入保护模式第一时间

* 执行的。但一般情况下,加载器会把它指向未解压的内核地址,hook比较少用。

*/

void go_to_protected_mode(void)

{

/* Hook before leaving real mode, also disables interrupts */

realmode_switch_hook();

/* Enable the A20 gate */

if (enable_a20()) {

puts("A20 gate not responding, unable to boot...\n");

die();

}

/* Reset coprocessor (IGNNE#) */

reset_coprocessor();

/* Mask all interrupts in the PIC */

mask_all_interrupts();

/* Actual transition to protected mode... */

setup_idt();

setup_gdt();

/*

* boot_params在boot/main.c中定义

* ds从header.S到现在还没变,还是指向内核加载基址X所在的段。

* ds<<4+boot_params就是为boot_params找到实际的地址。

* 内核中的函数都是fastcall的,则参数1被放在eax中,参数2被放入edx中。

*/

protected_mode_jump(boot_params.hdr.code32_start,

(u32)&boot_params + (ds() << 4));

}

a20.c//

/*

* Enable A20 gate (return -1 on failure)

* 在80286以前,intel的CPU只有20条地址线,可访问最高地址F000:FFFF=FFFFF,这种情况

* 下20根地址线全1。80286时,有24条地址线,可访问FFFF:FFFF=10FFEFh地址(地址格式没

* 变,只是范围大了),1M以上是extend memory,1M~10FFEFh为high memory。在80268以前

* 如果给的地址大于F000:FFFF,如FFFF:FFFF=10FFEFh,那么因为地址线只有20根,高于20

* 的地址部分将被弃掉,所以访问高于FFFF:FFFF实际上还是访问0FFEF。20根地址线最高

* 是1M内存地址,所以要访问逻辑地址高于1M,都会访问1M以下的地址,这种情况被称作是

* wraparound。而80286却能访问1M以上的地址。在80286实模式访问高端地址与8086不

* 一致,这像是一个bug。所以为了它们一致,人们引入了A20Gate:利用键盘控制器8042空

* 出的一个引脚和第20根地址线相与,以控制第20根。在80286实模式时,键盘控制器的这

* 个引脚是0。

* 注意一下,逻辑地址最高是FFFF:FFFF=FFFF0+FFFF=10FFEFh,在80286实模式下,就算访

* 问这个地址,因为它被人为地置0了,就与8086一样了。最高4位,由于逻辑地址限制,最

* 大值是0001,所以只要控制最高4位的的最低1位(A20)即可,因最高3位超出了逻辑地址

* 表达的范围,它们永远是0。当然,80286以后的CPU也保留着实模式(与8088)的一致性,

* 所以A20Gate一直存在。

* 但对于80286及其以后的CPU,有了保护模式,寻址范围变大,如32位的CPU,20位以上的

* 地址不再是仅有第20位是1、其它位是0了。而A20又成了遗留问题,进保护模式后,如果

* A20还保持着实模式时的值---0,那么会导致一个地址范围找不到。所以在切换到实

* 模式之间需要将A20Gate置为1。

* A20打开的方法不限于8042一种,随着技术的发展,厂商设计出了若干种打开A20的方法

* 下面会用到8042、0x92端口、bois(int15 ax=240x)

*/

#include "boot.h"

#define MAX_8042_LOOPS 100000

#define MAX_8042_FF 32

/*

* 0x64:状态寄存器、命令寄存器

* 0x60:数据寄存器

* 如果要读8042状态,直接读0x64端口,如果要写则将命令写到0x64,将参数

* 写到0x60,然后再读0x60端口取得返回值。

* 0x60R读输出缓冲区

* 0x60W写输入缓冲区(8042 Data&8048 Command)

* 0x64R读状态寄存器

* 0x64W写输入缓冲区(8042 Command)

* 端口0x64读出的状态(8位):

* 0 0x60端口有数据,系统应该将它读出

* 1 在输入寄存器中对8042有输入,来自0x60或0x64

* 2 0:reset

* 3 输入寄存器中的值是命令(1)还是数据(0)

* 4 键盘使能(1)禁用(0)

* 5 传输超时

* 6 接收超时

* 7 奇偶校验位 1=偶,0=奇,应该是奇

*/

static int empty_8042(void)

{

u8 status;

int loops = MAX_8042_LOOPS;

int ffs = MAX_8042_FF;

while (loops--) {

io_delay();

status = inb(0x64);

if (status == 0xff) {

/* FF is a plausible, but very unlikely status */

//返回ff说明8042控制器可能不存在

if (!--ffs)

return -1; /* Assume no KBC present */

}

/*

* 最低位是1说明60h端口有数据,将其读出

*/

if (status & 1) {

/* Read and discard input data */

io_delay();

(void)inb(0x60);

} else if (!(status & 2)) {

/* Buffers empty, finished! */

/*

* if句过滤最低位1,到此说明没有数据待读,最低位=0

* 此句又过滤掉bit1的1,那status最低2位应该是00

* 00表示0x60端口既没数据待读,系统也没往8042输入

* 数据或命令,8042empty了。

*/

return 0;

}

}

return -1;

}

/* Returns nonzero if the A20 line is enabled. The memory address

used as a test is the int $0x80 vector, which should be safe. */

#define A20_TEST_ADDR (4*0x80)

#define A20_TEST_SHORT 32

#define A20_TEST_LONG 2097152 /* 2^21 */

static int a20_test(int loops)

{

int ok = 0;

int saved, ctr;

set_fs(0x0000);

set_gs(0xffff);

/*

* fs:A20_TEST_ADDR=00000+4*0x80 =0000:0200

* gs:A20_TEST_ADDR+0x10=ffff0+4*0x80+0x10=0x100200

* wrfs32向fs写32位值,rdfs32从fs:addr处读出值

* wrfs32,rdgs32类似

*

* 上面说过80286实模式的wraparound现象,就是访问高端地址

* 时,由于A20的原因,最高位的1会被抛弃。那么,上面两个地

* 址,如果A20没打开的时候,读出的数据应该是相同的,异或时

* 结果等于0(ok=0)。对于下面的代码,分别从这两个地址读数

* 据,如果异或不是0,说明A20已经打开ok!=0,如果ok=0,说明

* A20没打开。当ok!=0时,会试loops次,确保不是偶然现象,代

* 码会要求loops的每一次都保证ok!=0(A20开启)。

*/

saved = ctr = rdfs32(A20_TEST_ADDR);

while (loops--) {

wrfs32(++ctr, A20_TEST_ADDR);

io_delay(); /* Serialize and make delay constant */

ok = rdgs32(A20_TEST_ADDR+0x10) ^ ctr;

if (ok)

break;

}

//将rdfs32处的值恢复原状

wrfs32(saved, A20_TEST_ADDR);

return ok;

}

/*

* Quick test to see if A20 is already enabled

* 用一个较短的循环来探测

*/

static int a20_test_short(void)

{

return a20_test(A20_TEST_SHORT);

}

/*

* Longer test that actually waits for A20 to come on line; this

* is useful when dealing with the KBC or other slow external circuitry.

* 用一个较长的循环来探测,当用慢速设备(8042)打开A20时,需要用这种方法探测

*/

static int a20_test_long(void)

{

return a20_test(A20_TEST_LONG);

}

/*

* int15也可用来打开A20,

* ax=0x2401 禁用

* ax=0x2402 启用

* ax=0x2403 查询A20状态

* ax=0x2404 查询A20支持情况(8042还是0x92端口)

*/

static void enable_a20_bios(void)

{

struct biosregs ireg;

initregs(&ireg);

ireg.ax = 0x2401;

intcall(0x15, &ireg, NULL);

}

static void enable_a20_kbc(void)

{

empty_8042();

outb(0xd1, 0x64); /* Command write写命令 */

empty_8042();

outb(0xdf, 0x60); /* A20 on,在0x60端口写入命令值(开A20Gate)*/

empty_8042();

outb(0xff, 0x64); /* Null command, but UHCI wants it */

empty_8042();

}

/*

* 0x92端口是快速的A20Gate,当系统没有键盘控制器时,就用这个端口

* bit 1:1,enable; 0,disable

* bit 0:1 reset; 0,no reset

*/

static void enable_a20_fast(void)

{

u8 port_a;

port_a = inb(0x92); /* Configuration port A */

port_a |= 0x02; /* Enable A20 */

port_a &= ~0x01; /* Do not reset machine */

outb(port_a, 0x92);

}

/*

* Actual routine to enable A20; return 0 on ok, -1 on failure

*/

#define A20_ENABLE_LOOPS 255 /* Number of times to try */

/*

* 这个函数会用三种方法来尝试打开A20Gate有一个能打开就成

*/

int enable_a20(void)

{

int loops = A20_ENABLE_LOOPS;

int kbc_err;

while (loops--) {

/* First, check to see if A20 is already enabled

(legacy free, etc.) */

if (a20_test_short())

return 0;

/* Next, try the BIOS (INT 0x15, AX=0x2401) */

enable_a20_bios();

if (a20_test_short())

return 0;

/* Try enabling A20 through the keyboard controller */

kbc_err = empty_8042();

//这句测试是防止bios打开A20的延时

if (a20_test_short())

return 0; /* BIOS worked, but with delayed reaction */

if (!kbc_err) {

enable_a20_kbc();

if (a20_test_long())

return 0;

}

/* Finally, try enabling the "fast A20 gate" */

enable_a20_fast();

if (a20_test_long())

return 0;

}

return -1;

}

//

有疑问加站长微信联系(非本文作者)

  • 0
    点赞
  • 0
    收藏
    觉得还不错? 一键收藏
  • 0
    评论
评论
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值