(参考文章)增加nand flash功能
(uboot分区参考)：uboot环境变量与内核MTD分区关系
移植环境
- 主机环境：VMare下RHLE6 ，1G内存。
- 编译编译环境：arm-linux-gcc v4.3.2
- 开发板：FL2440，4M nor flash，256M nand flash。
- u-boot版本：u-boot-2009.08
首先注意一个问题：
先请大家看《第五章 存储器控制器中》的Figure 5-1. S3C2440A Memory Map after Reset（也就是那个映射图），从理论上来讲，对于0x40000000以后的内存，只有在Nor boot的时候才存在；而在nandboot 的时候他被映射到了0x00000000，在0x40000000以后不存在内存。如果我们在启动的时候，将一些特定的数据写入0x40000000～0x40001000之间，那么按照数据手册上的说法，如果回读的结果和写入的一致说明是nor boot,否则就是nand boot! 这种办法理论上是通的，但是实际上，那个图是错的！！通过我的实验，正真的映射图如下：
从上图我们可以看出，无论是Nor boot还是nand boot ，这4K的内部SRAM都被映射到了0x40000000，而在nand boot的时候，这块内存同时还被映射到了0x00000000。那么一开始提出的办法就不可行了，而且在nand boot 的时候，写入0x40000000～0x40001000还会破坏自身的程序。
-
Nand flash或Nor flash双启动原理
首先，看一下我们熟悉的u-boot启动的时候执行的一段程序，这段程序一般存放在Nand flash中或Nor flash中。我们所说的Nand flash启动或Nor flash启动主要是涉及到一段搬移代码。这段搬移代码的功能是u-boot自己把自己搬移到内存中执行。如下是Nor flash启动中的这段搬移代码(这里以s3c2410为例)
relocate: /* relocate U-Boot to RAM */
adr r0, _start /* r0 <- current position of code */
ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
cmp r0, r1 /* don't reloc during debug */
beq stack_setup
ldr r2, _armboot_start
ldr r3, _bss_start
sub r2, r3, r2 /* r2 <- size of armboot */
add r2, r0, r2 /* r2 <- source end address */
copy_loop:
ldmia r0!, {r3-r10} /* copy from source address [r0] */
stmia r1!, {r3-r10} /* copy to target address [r1] */
cmp r0, r2 /* until source end addreee [r2] */
ble copy_loop
#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
#endif
上面这段代码就是把u-boot搬移到内存。而不同的启动方式区别也就在这段代码上，如果我们这里是Nand flash启动的话我们也需要写相同功能的代码，不同的是对于Nand的操作和Nor的操作是完全不同的，选择Nor flash启动是将Nor flash映射到片选0上也就是0x0地址而选择Nand flash启动则是将CPU的片内RAM(4K)映射到0地址，通过Nand flash控制器操作Nand flash。我们这里讨论如何实现Nand 和 Nor双启动。下面我们看看这两种启动的映射关系。
同时我们可以看到： 总线宽度和等待控制寄存器：
在系统重启时会扫描BWSCON的状态，而BWSCON的其他位的初始状态都是0，只有DW0(BWSCON[2:1])的值由OM[1:0]来决定，通过上面的2个图我们可以发现，我们可以通过判断BWSCON的第2位、第3位 {DW0（BWSCON[2:1])}的值，判断是Nor flash启动还是Nand Flash启动。
可以启动代码之前添加如下代码，来判断是Nor flash启动还是Nand Flash启动。
# define BWSCON 0x48000000
ldr r0,=BWSCON
ldr r0,[r0]
and r0,r0,#6
cmp r0, #0
bne relocate
///
//nand_boot
//Nand 搬移代码
relocate：
//nor_boot
//Nor 搬移代码
有了上面这段代码，就可以实现双启动了，只要再适当的添加对应的功能我们的uboot就完成了
-
为u-boot增加对nand flash支持实际操作
2.1 修改代码重定向部分，增加Nor flash 和Nand flash 双启动
修改cpu/arm920t/start.S文件，为使u-boot从Nand Flash启动，需要将下面注释掉的CPU和DRAM初始化部分还原。
用vim打开cpu/arm920t/start.S，定位到199行附近，找到如下代码
//#ifndef CONFIG_SKIP_LOWLEVEL_INIT
//bl cpu_init_crit
//#endif
将注释掉的这段代码恢复，修改如下：
#ifndef CONFIG_SKIP_LOWLEVEL_INIT
bl cpu_init_crit
#endif
- 判断当前代码位置，如果在内存，直接跳到stack_setup
#ifndef CONFIG_SKIP_RELOCATE_UBOOT
//relocate: /* relocate U-Boot to RAM */
/*---------------- Check the code position begain-----------*/
adr r0, _start /* r0 <- current position of code */
ldr r1, _TEXT_BASE /* test if we run from flash or RAM */
cmp r0, r1 /* don't reloc during debug */
beq stack_setup
/*------------------ Check the code position end -------------*/
-
如果不是在代码当前位置不再内存中，就判断启动的Flash：Nand 或者 Nor
/*------------ Check the boot flash begain --------------*/
# define BWSCON 0x48000000
ldr r0,=BWSCON
ldr r0,[r0]
ands r0,r0,#6
cmp r0, #0
bne relocate
/*-----------check the boot flash end-------------------*/
- 如果判断是在Nand Flash中启动的话，那么nand Flash搬移代码如下：
定义u-boot在nand flash中存放的长度为#define LENGTH_UBOOT 0x60000，可以方便修改u-boot因为裁剪和增添大小的改变而占的长度。
// copy U-Boot to RAM form Nand Flash
/*------------NAND BOOT start -------------------------*/
#define LENGTH_UBOOT 0x60000
#define NAND_CTL_BASE 0x4E000000
#ifdef CONFIG_S3C2440
/* Offset */
#define oNFCONF 0x00
#define oNFCONT 0x04
#define oNFCMD 0x08
#define oNFSTAT 0x20
@ reset NAND
mov r1, #NAND_CTL_BASE
ldr r2, =( (7<<12)|(7<<8)|(7<<4)|(0<<0) )
str r2, [r1, #oNFCONF]
ldr r2, [r1, #oNFCONF]
ldr r2, =( (1<<4)|(0<<1)|(1<<0) ) @ Active low CE Control
str r2, [r1, #oNFCONT]
ldr r2, [r1, #oNFCONT]
ldr r2, =(0x6) @ RnB Clear
str r2, [r1, #oNFSTAT]
ldr r2, [r1, #oNFSTAT]
mov r2, #0xff @ RESET command
strb r2, [r1, #oNFCMD]
mov r3, #0 @ wait
nand1:
add r3, r3, #0x1
cmp r3, #0xa
blt nand1
nand2:
ldr r2, [r1, #oNFSTAT] @ wait ready
tst r2, #0x4
beq nand2
ldr r2, [r1, #oNFCONT]
orr r2, r2, #0x2 @ Flash Memory Chip Disable
str r2, [r1, #oNFCONT]
@ get read to call C functions (for nand_read())
ldr sp, DW_STACK_START @ setup stack pointer
mov fp, #0 @ no previous frame, so fp=0
@ copy U-Boot to RAM
ldr r0, =TEXT_BASE
mov r1, #0x0
mov r2, #LENGTH_UBOOT
bl nand_read_ll
tst r0, #0x0
beq ok_nand_read
bad_nand_read:
loop2:
b loop2 @ infinite loop
ok_nand_read:
@ verify
mov r0, #0
ldr r1, =TEXT_BASE
mov r2, #0x400 @ 4 bytes * 1024 = 4K-bytes
go_next:
ldr r3, [r0], #4
ldr r4, [r1], #4
teq r3, r4
bne notmatch
subs r2, r2, #4
beq stack_setup
bne go_next
notmatch:
loop3:
b loop3 @ infinite loop
#endif
#ifdef CONFIG_S3C2410
/* Offset */
#define oNFCONF 0x00
#define oNFCMD 0x04
#define oNFSTAT 0x10
@ reset NAND
mov r1, #NAND_CTL_BASE
ldr r2, =0xf830 @ initial value
str r2, [r1, #oNFCONF]
ldr r2, [r1, #oNFCONF]
bic r2, r2, #0x800 @ enable chip
str r2, [r1, #oNFCONF]
mov r2, #0xff @ RESET command
strb r2, [r1, #oNFCMD]
mov r3, #0 @ wait
nand1:
add r3, r3, #0x1
cmp r3, #0xa
blt nand1
nand2:
ldr r2, [r1, #oNFSTAT] @ wait ready
tst r2, #0x1
beq nand2
ldr r2, [r1, #oNFCONF]
orr r2, r2, #0x800 @ disable chip
str r2, [r1, #oNFCONF]
@ get read to call C functions (for nand_read())
ldr sp, DW_STACK_START @ setup stack pointer
mov fp, #0 @ no previous frame, so fp=0
@ copy U-Boot to RAM
ldr r0, =TEXT_BASE
mov r1, #0x0
mov r2, #LENGTH_UBOOT
bl nand_read_ll
tst r0, #0x0
beq ok_nand_read
bad_nand_read:
loop2:
b loop2 @ infinite loop
ok_nand_read:
@ verify
mov r0, #0
ldr r1, =TEXT_BASE
mov r2, #0x400 @ 4 bytes * 1024 = 4K-bytes
go_next:
ldr r3, [r0], #4
ldr r4, [r1], #4
teq r3, r4
bne notmatch
subs r2, r2, #4
beq stack_setup
bne go_next
notmatch:
loop3:
b loop3 @ infinite loop
#endif
/*---------------NAND BOOT end ---------------*/
- 如果判断是在Nor Flash中启动的话，那么nor Flash搬移代码如下：
// copy U-Boot to RAM form Nor Flash
/*---------------NOR BOOT start------------------*/
relocate: ; relocate U-Boot to RAM
adr r0, _start ;r0 <- current position of code
ldr r1, _TEXT_BASE ; test if we run from flash or RAM
ldr r2, _armboot_start
ldr r3, _bss_start
sub r2, r3, r2 ;r2 <- size of armboot
add r2, r0, r2 ;r2 <- source end address
copy_loop:
ldmia r0!, {r3-r10} ; copy from source address [r0]
stmia r1!, {r3-r10} ; copy to target address [r1]
cmp r0, r2 ; until source end addreee [r2]
ble copy_loop
#endif /* CONFIG_SKIP_RELOCATE_UBOOT */
/*----------NOR BOOT end------------------------*/
/* Set up the stack */
stack_setup:
ldr r0, _TEXT_BASE ; upper 128 KiB: relocated uboot
sub r0, r0, #CONFIG_SYS_MALLOC_LEN ; malloc area
sub r0, r0, #CONFIG_SYS_GBL_DATA_SIZE ; bdinfo
-
在上面添加的代码中有一个跳转：bl nand_read_ll ，它跳入是新增的C 语言文件board/fl2440/nand_read.c中的函数，这个文件原本是用vivi 的代码，后来经过openmoko 的修改，并支持不同的Nand Flash 芯片，我又这里多加了几个个芯片ID以支持所有fl2440 的Nand Flash。代码如下：
/*
* nand_read.c: Simple NAND read functions for booting from NAND
*
* This is used by cpu/arm920/start.S assembler code,
* and the board-specific linker script must make sure this
* file is linked within the first 4kB of NAND flash.
*
* Taken from GPLv2 licensed vivi bootloader,
* Copyright (C) 2002 MIZI Research, Inc.
*
* Author: Hwang, Chideok <hwang@mizi.com>
* Date : $Date: 2004/02/04 10:37:37 $
*
* u-boot integration and bad-block skipping (C) 2006 by OpenMoko, Inc.
* Author: Harald Welte <laforge@openmoko.org>
*/
#include <common.h>
#include <linux/mtd/nand.h>
#define __REGb(x) (*(volatile unsigned char *)(x))
#define __REGw(x) (*(volatile unsigned short *)(x))
#define __REGi(x) (*(volatile unsigned int *)(x))
#define NF_BASE 0x4e000000
#if defined(CONFIG_S3C2410)
#define NFCONF __REGi(NF_BASE + 0x0)
#define NFCMD __REGb(NF_BASE + 0x4)
#define NFADDR __REGb(NF_BASE + 0x8)
#define NFDATA __REGb(NF_BASE + 0xc)
#define NFSTAT __REGb(NF_BASE + 0x10)
#define NFSTAT_BUSY 1
#define nand_select() (NFCONF &= ~0x800)
#define nand_deselect() (NFCONF |= 0x800)
#define nand_clear_RnB() do {} while (0)
#elif defined(CONFIG_S3C2440) || defined(CONFIG_S3C2442)
#define NFCONF __REGi(NF_BASE + 0x0)
#define NFCONT __REGi(NF_BASE + 0x4)
#define NFCMD __REGb(NF_BASE + 0x8)
#define NFADDR __REGb(NF_BASE + 0xc)
#define NFDATA __REGb(NF_BASE + 0x10)
#define NFDATA16 __REGw(NF_BASE + 0x10)
#define NFSTAT __REGb(NF_BASE + 0x20)
#define NFSTAT_BUSY 1
#define nand_select() (NFCONT &= ~(1 << 1))
#define nand_deselect() (NFCONT |= (1 << 1))
#define nand_clear_RnB() (NFSTAT |= (1 << 2))
#endif
static inline void nand_wait(void)
{
int i;
while (!(NFSTAT & NFSTAT_BUSY))
for (i=0; i<10; i++);
}
struct boot_nand_t {
int page_size;
int block_size;
int bad_block_offset;
// unsigned long size;
};
#if 0
#if defined(CONFIG_S3C2410) || defined(CONFIG_FL2440)
/* configuration for 2410 with 512byte sized flash */
#define NAND_PAGE_SIZE 512
#define BAD_BLOCK_OFFSET 5
#define NAND_BLOCK_MASK (NAND_PAGE_SIZE - 1)
#define NAND_BLOCK_SIZE 0x4000
#else
/* configuration for 2440 with 2048byte sized flash */
#define NAND_5_ADDR_CYCLE
#define NAND_PAGE_SIZE 2048
#define BAD_BLOCK_OFFSET NAND_PAGE_SIZE
#define NAND_BLOCK_MASK (NAND_PAGE_SIZE - 1)
#define NAND_BLOCK_SIZE (NAND_PAGE_SIZE * 64)
#endif
/* compile time failure in case of an invalid configuration */
#if defined(CONFIG_S3C2410) && (NAND_PAGE_SIZE != 512)
#error "S3C2410 does not support nand page size != 512"
#endif
#endif
static int is_bad_block(struct boot_nand_t * nand, unsigned long i)
{
unsigned char data;
unsigned long page_num;
nand_clear_RnB();
if (nand->page_size == 512) {
NFCMD = NAND_CMD_READOOB; /* 0x50 */
NFADDR = nand->bad_block_offset & 0xf;
NFADDR = (i >> 9) & 0xff;
NFADDR = (i >> 17) & 0xff;
NFADDR = (i >> 25) & 0xff;
} else if (nand->page_size == 2048) {
page_num = i >> 11; /* addr / 2048 */
NFCMD = NAND_CMD_READ0;
NFADDR = nand->bad_block_offset & 0xff;
NFADDR = (nand->bad_block_offset >> 8) & 0xff;
NFADDR = page_num & 0xff;
NFADDR = (page_num >> 8) & 0xff;
NFADDR = (page_num >> 16) & 0xff;
NFCMD = NAND_CMD_READSTART;
} else {
return -1;
}
nand_wait();
data = (NFDATA & 0xff);
if (data != 0xff)
return 1;
return 0;
}
static int nand_read_page_ll(struct boot_nand_t * nand, unsigned char *buf, unsigned long addr)
{
unsigned short *ptr16 = (unsigned short *)buf;
unsigned int i, page_num;
nand_clear_RnB();
NFCMD = NAND_CMD_READ0;
if (nand->page_size == 512) {
/* Write Address */
NFADDR = addr & 0xff;
NFADDR = (addr >> 9) & 0xff;
NFADDR = (addr >> 17) & 0xff;
NFADDR = (addr >> 25) & 0xff;
} else if (nand->page_size == 2048) {
page_num = addr >> 11; /* addr / 2048 */
/* Write Address */
NFADDR = 0;
NFADDR = 0;
NFADDR = page_num & 0xff;
NFADDR = (page_num >> 8) & 0xff;
NFADDR = (page_num >> 16) & 0xff;
NFCMD = NAND_CMD_READSTART;
} else {
return -1;
}
nand_wait();
#if defined(CONFIG_S3C2410)
for (i = 0; i < nand->page_size; i++) {
*buf = (NFDATA & 0xff);
buf++;
}
#elif defined(CONFIG_S3C2440) || defined(CONFIG_S3C2442)
for (i = 0; i < (nand->page_size>>1); i++) {
*ptr16 = NFDATA16;
ptr16++;
}
#endif
return nand->page_size;
}
static unsigned short nand_read_id(void)
{
unsigned short res = 0;
NFCMD = NAND_CMD_READID;
NFADDR = 0;
res = NFDATA;
res = (res << 8) | NFDATA;
return res;
}
extern unsigned int dynpart_size[];
/* low level nand read function */
int nand_read_ll(unsigned char *buf, unsigned long start_addr, int size)
{
int i, j;
unsigned short nand_id;
struct boot_nand_t nand;
/* chip Enable */
nand_select();
nand_clear_RnB();
for (i = 0; i < 10; i++)
;
nand_id = nand_read_id();
if (0) { /* dirty little hack to detect if nand id is misread */
unsigned short * nid = (unsigned short *)0x31fffff0;
*nid = nand_id;
}
if (nand_id == 0xec76 /* Samsung K91208 */
||nand_id == 0xad76 ) { /*Hynix HY27US08121A*/
nand.page_size = 512;
nand.block_size = 16 * 1024;
nand.bad_block_offset = 5;
// nand.size = 0x4000000;
} else if (nand_id == 0xecf1 /* Samsung K9F1G08U0B */
||nand_id == 0xecda /* Samsung K9F2G08U0B */
||nand_id == 0xecd3 ) { /* Samsung K9K8G08 */
nand.page_size = 2048;
nand.block_size = 128 * 1024;
nand.bad_block_offset = nand.page_size;
// nand.size = 0x8000000;
} else {
return -1; // hang
}
if ((start_addr & (nand.block_size-1)) || (size & ((nand.block_size-1))))
return -1; /* invalid alignment */
for (i=start_addr; i < (start_addr + size);) {
#ifdef CONFIG_S3C2410_NAND_SKIP_BAD
//if (i & (nand.block_size-1)== 0) {//warning: suggest parentheses around comparison in operand of '&'
if ((i & (nand.block_size-1))== 0) {
if (is_bad_block(&nand, i) ||
is_bad_block(&nand, i + nand.page_size)) {
/* Bad block */
i += nand.block_size;
size += nand.block_size;
continue;
}
}
#endif
j = nand_read_page_ll(&nand, buf, i);
i += j;
buf += j;
}
/* chip Disable */
nand_deselect();
return 0;
}
然后保存为nand_read.c，还要记得路径是在board /fl2440/目录下。
注意：上面这段代码中对Nand进行寻址的部分，这跟具体的Nand Flash的寻址方式有关。
根据我们开发板上的Nand Flash(K9F2G08x0a)数据手册得知，片内寻址是采用28位地址形式。从第0位开始分五次通过I/O0－I/O7进行传送，并进行片内寻址。具体含义和结构图如下(相关概念参考Nand数据手册)：
0-11位：Y-Buffers偏移地址
12-28位：X-Buffers偏移地址
2.3. 在board/fl2440/Makefile中添加nand_read.c的编译选项，使他编译到u-boot中，修改后代码如下：
include $(TOPDIR)/config.mk
LIB = $(obj)lib$(BOARD).a
COBJS := nand_read.o fl2440.o flash.o
SOBJS := lowlevel_init.o
2.4. 在fl2440.h头文件中加入Nand要用到的宏和寄存器的定义。
用vim打开include/configs/fl2440.h头文件，定位到文件末尾处加入下列代码：
/*-----------------------------------------------------------------------
* NAND flash settings
*/
#define CONFIG_S3C2410_NAND_SKIP_BAD 1
2.5. 在cpu/arm920t/u-boot.lds中添加下面两行代码，主要目的是防止编译器把我们自己添加的用于nandboot的子函数放到4K之后，否则是无法启动的，修改后代码如下：
.text :
{
cpu/arm920t/start.o (.text)
board/samsung/fl2440/lowlevel_init.o (.text)
board/samsung/fl2440/nand_read.o (.text)
*(.text)
}
现在的Nand还不能做任何事情，而且也没有显示有关Nand的任何信息，所以只能说明上面的这些步骤只是完成了Nand移植的Stage1部分。下面我们来添加我们开发板上的Nand Flash(K9F2G08x0A)的Stage2部分的有关操作支持。
-
Uboot第二间断nandflash移植
在U-boot 启动的第一阶段，初始化了Nand Flash 控制器。但到第二阶段start_armboot函数还是会再次初始化Nand Flash 控制器。因为第二阶段和第一阶段的代码基本是独立的，第一阶段的代码基本只起到代码重定位的作用，到了第二阶段才是真正U-boot 的开始，以前的初始化过程还会重做一遍，比如始化Nand Flash 控制器、CPU 频率等。因为 S3C2440 和S3C2410 之间的很大差别就是：S3C2410 的Nand Flash 控制器只支持512B+16B 的Nand Flash，而S3C2440 还支持2KB+64B 的大容量Nand Flash。所以在Nand Flash 控制器上寄存器和控制流程上的差别很明显，底层驱动代码的修改也是必须的。具体的差别还是需要对比芯片数据手册的，下面我们结合代码来分析一下u-boot在第二阶段的执行流程：
<1>. lib_arm/board.c文件中的start_armboot函数调用了drivers/mtd/nand/nand.c文件中的nand_init函数，如下：
#if defined(CONFIG_CMD_NAND) //可以看到CONFIG_CMD_NAND宏决定了Nand的初始化
puts ("NAND: ");
nand_init();
#endif
<2>. nand_init调用了同文件下的nand_init_chip函数；
<3>. nand_init_chip函数调用drivers/mtd/nand/s3c2410_nand.c文件下的board_nand_init函数，然后再调用drivers/mtd/nand/nand_base.c函数中的nand_scan函数；
<4>.nand_scan函数调用了同文件下的nand_scan_ident函数等。
-
Nand Flash 相关代码的修改
打开/drivers/mtd/nand/s3c2410_nand.c，定位到37行，修改如下：
#define __REGb(x) (*(volatile unsigned char *)(x))
#define __REGi(x) (*(volatile unsigned int *)(x))
#define NF_BASE 0x4e000000
#if defined(CONFIG_S3C2410)
#define NFCONF __REGi(NF_BASE + 0x0)
#define NFCMD __REGb(NF_BASE + 0x4)
... ...
#define S3C2410_ADDR_NALE 4
#define S3C2410_ADDR_NCLE 8
#endif
#if defined(CONFIG_S3C2440)
#define S3C2410_ADDR_NALE 0x08
#define S3C2410_ADDR_NCLE 0x0c
#define NFCONF __REGi(NF_BASE + 0x0)
#define NFCONT __REGb(NF_BASE + 0x4)
#define NFCMD __REGb(NF_BASE + 0x8)
#define NFADDR __REGb(NF_BASE + 0xc)
#define NFDATA __REGb(NF_BASE + 0x10)
#define NFMECCD0 __REGb(NF_BASE + 0x14)
#define NFMECCD1 __REGb(NF_BASE + 0x18)
#define NFSECCD __REGb(NF_BASE + 0x1c)
#define NFSTAT __REGb(NF_BASE + 0x20)
#define NFESTAT0 __REGb(NF_BASE + 0x24)
#define NFESTAT1 __REGb(NF_BASE + 0x28)
#define NFMECC0 __REGb(NF_BASE + 0x2c)
#define NFMECC1 __REGb(NF_BASE + 0x30)
#define NFSECC __REGb(NF_BASE + 0x34)
#define NFSBLK __REGb(NF_BASE + 0x38)
#define NFEBLK __REGb(NF_BASE + 0x3c)
#define NFECC0 __REGb(NF_BASE + 0x2c)
#define NFECC1 __REGb(NF_BASE + 0x2d)
#define NFECC2 __REGb(NF_BASE + 0x2e)
#define S3C2410_NFCONT_EN (1<<0)
#define S3C2410_NFCONT_INITECC (1<<4)
#define S3C2410_NFCONT_nFCE (1<<1)
#define S3C2410_NFCONT_MAINECCLOCK (1<<5)
#define S3C2410_NFCONF_TACLS(x) ((x)<<12)
#define S3C2410_NFCONF_TWRPH0(x) ((x)<<8)
#define S3C2410_NFCONF_TWRPH1(x) ((x)<<4)
#endif
ulong IO_ADDR_W = NF_BASE;
static void s3c2410_hwcontrol(struct mtd_info *mtd, int cmd, unsigned int ctrl)
{
//struct nand_chip *chip = mtd->priv;
DEBUGN("hwcontrol(): 0x%02x 0x%02x\n", cmd, ctrl);
if (ctrl & NAND_CTRL_CHANGE) {
//ulong IO_ADDR_W = NF_BASE;//应注释掉这个局部变量否则找不到ID "No NAND device found!!!"
IO_ADDR_W = NF_BASE;
if (!(ctrl & NAND_CLE))
IO_ADDR_W |= S3C2410_ADDR_NCLE;
if (!(ctrl & NAND_ALE))
IO_ADDR_W |= S3C2410_ADDR_NALE;
//chip->IO_ADDR_W = (void *)IO_ADDR_W;
#if defined(CONFIG_S3C2410)
if (ctrl & NAND_NCE)
NFCONF &= ~S3C2410_NFCONF_nFCE;
else
NFCONF |= S3C2410_NFCONF_nFCE;
#endif
#if defined(CONFIG_S3C2440)
if (ctrl & NAND_NCE)
NFCONT &= ~S3C2410_NFCONT_nFCE;
else
NFCONT |= S3C2410_NFCONT_nFCE;
#endif
}
if (cmd != NAND_CMD_NONE)
//writeb(cmd, chip->IO_ADDR_W);
writeb(cmd, (void *)IO_ADDR_W);
}
... ...
#ifdef CONFIG_S3C2410_NAND_HWECC
void s3c2410_nand_enable_hwecc(struct mtd_info *mtd, int mode)
{
DEBUGN("s3c2410_nand_enable_hwecc(%p, %d)\n", mtd, mode);
#if defined(CONFIG_S3C2410)
NFCONF |= S3C2410_NFCONF_INITECC;
#endif
#if defined(CONFIG_S3C2440)
NFCONT |= S3C2410_NFCONT_INITECC;
#endif
}
... ...
#endif
int board_nand_init(struct nand_chip *nand)
{
u_int32_t cfg;
u_int8_t tacls, twrph0, twrph1;
S3C24X0_CLOCK_POWER * const clk_power = S3C24X0_GetBase_CLOCK_POWER();
DEBUGN("board_nand_init()\n");
clk_power->CLKCON |= (1 << 4);
/* initialize hardware */
#if defined(CONFIG_S3C2410)
twrph0 = 3; twrph1 = 0; tacls = 0;
cfg = S3C2410_NFCONF_EN;
cfg |= S3C2410_NFCONF_TACLS(tacls - 1);
cfg |= S3C2410_NFCONF_TWRPH0(twrph0 - 1);
cfg |= S3C2410_NFCONF_TWRPH1(twrph1 - 1);
NFCONF = cfg;
/* initialize nand_chip data structure */
nand->IO_ADDR_R = nand->IO_ADDR_W = (void *)0x4e00000c;
#endif
#if defined(CONFIG_S3C2440)
twrph0 = 4; twrph1 = 2; tacls = 0;
cfg = 0;
cfg |= S3C2410_NFCONF_TACLS(tacls - 1);
cfg |= S3C2410_NFCONF_TWRPH0(twrph0 - 1);
cfg |= S3C2410_NFCONF_TWRPH1(twrph1 - 1);
NFCONF = cfg;
NFCONT = (0<<13)|(0<<12)|(0<<10)|(0<<9)|(0<<8)|(0<<6)|(0<<5)|(1<<4)|(0<<1)|(1<<0);
/* initialize nand_chip data structure */
nand->IO_ADDR_R = nand->IO_ADDR_W = (void *)0x4e000010;
#endif
/* read_buf and write_buf are default */
/* read_byte and write_byte are default */
-
在fl2440.h里添加nand_flash相关宏定义
打开include/configs/fl2440.h，定位到98行附近，加入下列代码：
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_DATE
#define CONFIG_CMD_ELF
#define CONFIG_CMD_NAND
#define CONFIG_CMD_JFFS2 /* JFFS2 Support*/
... ...
在文件末尾处加入下列代码：
/*-----------------------------------------------------------------------
* NAND flash settings
*/
#if defined(CONFIG_CMD_NAND)
#define CONFIG_NAND_S3C2410
#define CONFIG_SYS_NAND_BASE 0x4E000000
#define CONFIG_SYS_MAX_NAND_DEVICE 1 /* Max number of NAND devices */
#define SECTORSIZE 512
#define SECTORSIZE_2K 2048
#define NAND_SECTOR_SIZE SECTORSIZE
#define NAND_SECTOR_SIZE_2K SECTORSIZE_2K
#define NAND_BLOCK_MASK 511
#define NAND_BLOCK_MASK_2K 2047
#define NAND_MAX_CHIPS 1
#define CONFIG_MTD_NAND_VERIFY_WRITE
#define CONFIG_SYS_64BIT_VSPRINTF /* needed for nand_util.c */
#endif /* CONFIG_CMD_NAND */
#define CONFIG_S3C2410_NAND_SKIP_BAD 1
u-boot在默认的情况下把环境变量都是保存到Nor Flash中的，所以我们要修改代码，让它保存到Nand中，如下：
打开include/configs/fl2440.h，定位到193行附近，注释掉下列代码：
/* timeout values are in ticks */
#define CONFIG_SYS_FLASH_ERASE_TOUT (5*CONFIG_SYS_HZ) /* Timeout for Flash Erase */
#define CONFIG_SYS_FLASH_WRITE_TOUT (5*CONFIG_SYS_HZ) /* Timeout for Flash Write */
//#define CONFIG_ENV_IS_IN_FLASH 1
//#define CONFIG_ENV_SIZE 0x20000 /* Total Size of Environment Sector */
然后加入下列代码：
/*-----------------------------------------------------------------------
* NAND flash settings
*/
#define CONFIG_ENV_IS_IN_NAND 1
#define CONFIG_ENV_OFFSET 0x40000 //将环境变量保存到nand中的0x40000位置必，须在块的起始位置
#define CONFIG_ENV_SIZE 0x20000 //必须为块大小的整数倍 ， 否则会提示下面的信息，将擦除整个块
#if defined(CONFIG_CMD_NAND)
Warning: Erase size 0x00010000 smaller than one erase block 0x00020000
Erasing 0x00020000 instead
NAND 128MiB 3,3V 8-bit: MTD Erase failure: -22
Writing to Nand... FAILED!
扫一扫
2125
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
