实验拓扑

wKioL1WeCvKD9ghQAAE3af4lVT4686.jpg

实验需求

1、C1与C3属于vlan10,C2与C4属于vlan20


2、SW1与SW2之间使用LACP模式链路捆绑,活动接口为2个


3、SW1与R1之间进行链路混绑


4、VLAN 10 与 VLAN 20 通过DHCP自动获取IP地址


5、在R1上配置单臂路由使全网互通


vlan10 IP:192.168.10.0/24

vlan20 IP:192.168.20.0/24


SW1配置:

<SW1>system-view                //进入系统视图

[SW1]vlan batch 10 20          //创建vlan

[SW1]inter e0/0/1                     //进接口

[SW1-Ethernet0/0/1]port hybrid pvid vlan 10      //为进来的数据包加vlan10标签

[SW1-Ethernet0/0/1]port hybrid untagged vlan 10   //将接口以untagged方式加入vlan10

[SW1-Ethernet0/0/1]quit

[SW1]inter e0/0/2

[SW1-Ethernet0/0/2]port hybrid pvid vlan 20

[SW1-Ethernet0/0/2]port hybrid untagged vlan 20

[SW1-Ethernet0/0/2]quit

[SW1]lacp priority 100                //配置系统优先级为100

[SW1]inter eth-trunk 1                 //进入eth-trunk 1

[SW1-Eth-Trunk1]mode lacp-static        //设置为lacp模式

[SW1-Eth-Trunk1]max active-linknumber 2      //设置活动接口为2

[SW1-Eth-Trunk1]port hybrid tagged vlan 10 20   //将接口以tagged方式加入到vlan10和vlan20,设置中继

[SW1-Eth-Trunk1]quit

[SW1]interface e0/0/10             //进接口

[SW1-Ethernet0/0/10]eth-trunk 1     //将接口加入eth-trunk

[SW1-Ethernet0/0/10]lacp priority 100   //设置接口优先级为100,默认为32768

[SW1-Ethernet0/0/10]inter e0/0/11

[SW1-Ethernet0/0/11]eth-trunk 1

[SW1-Ethernet0/0/11]inter e0/0/12

[SW1-Ethernet0/0/12]eth-trunk 1

[SW1-Ethernet0/0/12]quit

[SW1]interface Eth-Trunk 2                 //进入eth-trunk 2

[SW1-Eth-Trunk2]trunkport GigabitEthernet 0/0/1 0/0/2   //将接口加入到eth-trunk中

[SW1-Eth-Trunk2]port hybrid tagged vlan 10 20         //将接口以tagged方式加入到vlan10和vlan20



SW2配置:


<SW2>system-view 

[SW2]vlan batch 10 20

[SW2]inter e0/0/3

[SW2-Ethernet0/0/3]port hybrid pvid vlan 10

[SW2-Ethernet0/0/3]port hybrid untagged vlan 10

[SW2-Ethernet0/0/3]quit

[SW2]interface e0/0/4

[SW2-Ethernet0/0/4]port hybrid pvid vlan 20

[SW2-Ethernet0/0/4]port hybrid untagged vlan 20

[SW2-Ethernet0/0/4]quit

[SW2]interface Eth-trunk 1

[SW2-Eth-Trunk1]mode lacp-static 

[SW2-Eth-Trunk1]max active-linknumber 2

[SW2-Eth-Trunk1]trunkport Ethernet 0/0/10 to 0/0/12

[SW2-Eth-Trunk1]port hybrid tagged vlan 10 20


wKioL1WeEUKyu8h5AAH22p55RC0852.jpg

通过display eth-trunk 1 查看端口信息,发现优先级高的e0/0/10,e0/0/11接口被选中为活动接口优先级低的未被


在SW1上关闭一个端口SW1


[SW1]interface e0/0/10

[SW1-Ethernet0/0/10]shutdown


wKiom1WeIMfAgvRiAAGzunR3qPA177.jpg

会发现0/0/10接口关闭了以后 0/0/12接口自动补上了


R1配置:

<R1>system-view 

[R1]dhcp enable 

[R1]interface Eth-Trunk 1            //进入eth-trunk 1 

[R1-Eth-Trunk1]undo portswitch       //转换三层口,默认eth-trunk是二层口路由是三层端口要把接口转换成三层接口才可以捆绑

[R1-Eth-Trunk1]trunkport GigabitEthernet 0/0/1 0/0/2     //将接口加入eth-trunk

[R1]interface Eth-Trunk 1.10        //进入子接口

[R1-Eth-Trunk1.10]dot1q termination vid 10    //封装dot1q,设置为vlan10的网关

[R1-Eth-Trunk1.10]ip address 192.168.10.1 24    //配置接口IP

[R1-Eth-Trunk1.10]arp broadcast enable     //开启ARP广播

[R1-Eth-Trunk1.10]dhcp select interface   //采用接口地址池的DHCP功能

[R1-Eth-Trunk1.10]inter eth-trunk 1.20

[R1-Eth-Trunk1.20]dot ter vid 20

[R1-Eth-Trunk1.20]ip add 192.168.20.1 24

[R1-Eth-Trunk1.20]a b e

[R1-Eth-Trunk1.20]dhcp sel int



用PC自动获取DHCP

wKioL1WeNDPx_uGAAAHFBwSKGuU762.jpg

wKiom1WeMqbj-GjAAAGR2BbxR6g570.jpg

C2获取

wKiom1WeMvSjNx_IAAGGV3A-EAg655.jpg

C3获取

wKiom1WeM1LQM7n8AAGVK4iZtog697.jpg

C4获取

wKiom1WeM6CBaN7NAAGQiZdWiKc740.jpg


C1去测试,全网互通

wKioL1WeNmCRH2mMAANMzSzPDbs976.jpg