RT-11SJ 环境下运行pdp11汇编MACRO-11

2019独角兽企业重金招聘Python工程师标准>>>

一、在simh下运行RT-11SJ

1:安装simh：win下直接安装，linux下make后在BIN目录找到pdp11并cp到搜索路径目录下

2:到http://simh.trailing-edge.com/software.html 下载RT-11 V4 for the PDP-11 的镜像磁盘文件rt11swre.tar.Z并解压，在Disks目录下可得到镜像文件rtv4_rk.dsk

3:建立运行目录rt11swre，把rtv4_rk.dsk移到该目录

4:建立simh启动文件boot.ini如下：rt11swre$ cat boot.ini 

set cpu 256k

att rk0 rtv4_rk.dsk

boot rk0

5:启动pdp11   

$ pdp11 boot.ini 

PDP-11 simulator V3.9-0

Disabling CR

RT-11SJ  V04.00C 

.D 56=5015

.TYPE V4USER.TXT

Welcome to RT-11 Version 4. RT-11 V04 provides new hardware support

and some major enhancements over Version 3B.

Please use the HELP command;  it describes the new options in many

of the utilities.

If you are using a terminal that requires fill characters,

modify location 56 with a Deposit command before proceeding with

system installation. LA36 DECwriter II and VT52 DECscope terminals

do NOT require such modification.

.D 56=0

.

.号为 RT-11操作系统的命令提示符（类似dos下的c:\>或unix下的$）

二、在RT-11环境下输入HELLO.MAC源程序

编辑程序EDIT我不会用，这里用COPY命令（类似在unix用cat命令创建文件的方法）：

.COPY TT: HELLO.MAC

 Files copied:

^.TITLE  HELLO WORLD

        .MCALL  .TTYOUT,.EXIT

HELLO:: MOV     #MSG,R1  ;STARTING ADDRESS OF STRING

1$:     MOVB    (R1)+,R0 ;FETCH NEXT CHARACTER

        BEQ     DONE     ;IF ZERO, EXIT LOOP

        .TTYOUT          ;OTHERWISE PRINT IT

        BR      1$       ;REPEAT LOOP

DONE:   .EXIT

MSG:    .ASCIZ /HELLO, WORLD!/

        .END    HELLO

^ZTT:            to DK:HELLO.MAC

注意最后一行(必须另起一行、不能在.END HELLO后面)只需输入ctrl+Z文件便会保存到磁盘

 .DIR *.MAC

 

HELLO .MAC     1                 

 1 Files, 1 Blocks

 2496 Free blocks

三、汇编

.MACRO HELLO

ERRORS DETECTED:  0

四、连接并运行

.LINK HELLO

.R HELLO

HELLO, WORLD!

更简单的HELLOWORLD：

;        MACRO-11  EXAMPLE.

       .MCALL  .EXIT, .PRINT

START:

        .PRINT  #MES

        .EXIT

MES:    .ASCIZ  /HELLO !!!/

.END    START

还有一个版本：

.MCALL .REGDEF,.TTYOUT,.EXIT

.REGDEF

HELLO:

        MOV #MSG,R1

        MOVB (R1),R0

        LOOP: .TTYOUT

        MOVB (R1)+,R0

        BNE LOOP

        .EXIT

MSG: .ASCIZ /HELLO, WORLD!/

.END HELLO

.TITLE  HELLO WORLD
        .MCALL  .TTYOUT,.EXIT
HELLO:: MOV     #MSG,R1  ;STARTING ADDRESS OF STRING
1$:     MOVB    (R1)+,R0 ;FETCH NEXT CHARACTER
        BEQ     DONE     ;IF ZERO, EXIT LOOP
        .TTYOUT          ;OTHERWISE PRINT IT
        BR      1$       ;REPEAT LOOP
DONE:   .EXIT

MSG:    .ASCIZ /HELLO, WORLD!/
        .END    HELLO

;        MACRO-11  EXAMPLE.

       .MCALL  .EXIT, .PRINT

START:
        .PRINT  #MES
        .EXIT

MES:    .ASCIZ  /HELLO !!!/

.END    START

.MCALL .REGDEF,.TTYOUT,.EXIT

.REGDEF
HELLO:
        MOV #MSG,R1
        MOVB (R1),R0
        LOOP: .TTYOUT
        MOVB (R1)+,R0
        BNE LOOP
        .EXIT

MSG: .ASCIZ /HELLO, WORLD!/
.END HELLO

Installing RT-11 5.3 on SIMH

 

转载于:https://my.oschina.net/u/2245781/blog/505415