1.Refer to the exhibit. Why was this message received?<?xml:namespace prefix = o ns = "urn:schemas-microsoft-com:office:office" />

A.No VTY password has been set.
B.No enable password has been set.
C.No console password has been set.
D.No enable secret password has been set.
E.The login command has not been set . CON 0.
F.The login command has not been set . the VTY ports.
Correct:A
2.A network administrator needs to create 29 subnetworks while maximizing the number of host addresses available . each subnet. How many bits must be borrowed from the host field of the network address to provide the required number of subnets with the most hosts per subnet?
A.2
B<?xml:namespace prefix = st1 ns = "urn:schemas-microsoft-com:office:smarttags" />.3
C.4
D.5
E.6
F.7
Correct:D
3.Refer to the exhibit. If host A sends an IP packet to host B, what will the OSI Layer 3 source address be in the packet when it reaches host B?

A.10.168.10.99
B.10.168.11.88
C.10.168.11.65
D.A1:A1:A1:A1:A1:A1
E.B2:B2:B2:B2:B2:B2
F.C3:C3:C3:C3:C3:C3
Correct:A
4.What is the difference between the Cisco router IOS commands show cdp neighbor detail and show cdp entry?
A.The show cdp neighbor detail command shows all neighbor information, while show cdp entry displays .ly .e line of output for each neighbor.
B.The show cdp entry command shows neighbor information for specific neighbors .ly, while show cdp neighbor detail lists each neighbor with detailed output . each.
C.The show cdp entry command shows neighbor information for all neighbors with .e line of output for each, while show cdp neighbor detail lists each neighbor with detailed output . each.
D.The show cdp neighbor detail command shows neighbor information for a single neighbor .ly, while show cdp entry displays detailed output . each neighbor known.
Correct:B
5.Refer to the exhibit. A person is trying to send a file from a host . Network A of the JAX Company to a server . Network Z of the XYZ Company. The file transfer fails. The host . Network A can communicate with other hosts . Network A. Which command, issued from router RTA, would be the most useful for troubleshooting this problem?

A.show flash:
B.show history
C.show version
D.show interfaces
E.show controllers serial
Correct:D
6.drag drop

Correct:
Green choice10---->Yellow Choice1
Green choice2---->Yellow Choice2
Green choice5---->Yellow Choice3
Green choice3---->Yellow Choice4
Green choice8---->Yellow Choice5
7.Which Layer 4 protocol is used for a Telnet connection?
A.IP
B.TCP
C.UDP
D.ICMP
E.DNS
Correct:B
8.What is the subnet address of 172.16.159.159/22?
A.172.16.0.0
B.172.16.128.0
C.172.16.156.0
D.172.16.159.0
E.172.16.159.128
F.172.16.192.0
Correct:C
9.What is the purpose of flow control?
A.to ensure data is retransmitted if an acknowledgment is not received
B.to reassemble segments in the correct order at the destination device
C.to provide a means for the receiver to govern the amount of data sent by the sender
D.to regulate the size of each segment
Correct:C
10.During the boot sequence, a 2600 series router needs to locate and load an operating system. What is the default order the router uses to find an operating system?
A.Flash, TFTP server, ROM
B.Flash, TFTP server, RAM
C.Flash, NVRAM, TFTP server
D.ROM, TFTP server, Flash
E.Flash, ROM, TFTP server
Correct:A
11.What is the subnet address for the IP address 172.19.20.23/28?
A.172.19.20.0
B.172.19.20.15
C.172.19.20.16
D.172.19.20.20
E.172.19.20.32
Correct:C
12.Which two statements describe the IP address 10.16.3.65/23? (Choose two.)
A.The subnet address is 10.16.3.0 255.255.254.0.
B.The lowest host address in the subnet is 10.16.2.1 255.255.254.0.
C.The last valid host address in the subnet is 10.16.2.254 255.255.254.0
D.The broadcast address of the subnet is 10.16.3.255 255.255.254.0.
E.The network is not subnetted.
Correct:B D
13.An administrator issues the show ip interface s0/0 command and the output displays the line Serial0/0 is up, line protocol is upWhat does "line protocol is up" specifically indicate about the interface?
A.Keepalives are being received . the interface.
B.The cable is attached properly.
C.CDP has discovered the connected device.
D.A carrier detect signal has been received from the connected device.
E.IP is correctly configured . the interface.
Correct:A
14.The Hub and Spoke routers are directly connected through their serial interfaces for purposes of testing. Based . the output shown in the exhibit, what must be done to make the serial line operational?

A.Start the clock . the Hub router.
B.Change the IP address . the Spoke router.
C.Configure the serial 0/0 interface . the Spoke router with a clockrate.
D.Replace the broken cable between the two devices.
E.Use the no shutdown command . the Hub router.
Correct:C
15.Which command will reinitialize the router and totally replace the running configuration with the current startup configuration?
A.router# reload
B.router# copy tftp startup-config
C.router# copy startup-config running-config
D.router# copy running-config flash
E.router# setup
F.router# restart
Correct:A
16.Refer to the graphic. What is the purpose of the two numbers shown following the exec-timeout command?

A.If no commands have been typed in 55 seconds, the console connection will be closed.
B.If no router activity has been detected in .e hour and 55 minutes, the console will be locked out.
C.If no commands have been typed in .e minute and 55 seconds, the console connection will be closed.
D.If connected to the router by Telnet, input must be detected within .e hour and 55 seconds or the connection will be closed.
E.If connected to the router by Telnet, input must be detected within .e minute and 55 seconds or the connection will be closed.
Correct:C
17.How will a Cisco 2600 series router respond if the conditions listed below exist during the boot process? 1) The IOS image in flash is missing. 2) No network connectivity is available. 3) The router fallback IOS image is corrupt.
A.The router will enter setup mode.
B.The router will enter ROM monitor mode.
C.The router will enter global configuration mode.
D.The boot will hang until an IOS is available.
E.The router will enter the prompted setup dialog.
Correct:B
18.A router receives a packet . interface 172.16.45.66/26. The source IP of the packet is 172.16.45.126/26 and the destination is 172.16.46.191/26. How will the router handle the packet?
A.The destination is a host . another subnet, so the router will not forward the packet.
B.The destination is a host . the same subnet, so the router will forward the packet.
C.The destination is a broadcast address, so the router will not forward the packet.
D.The destination is a network address, so the router will forward the packet.
Correct:C
19.Host A needs to communicate with the email server shown in the graphic. What address will be placed in the destination address field of the frame when it leaves Host A?

A.the MAC address of Host A
B.the MAC address of Switch 1
C.the MAC address of E0 of the router
D.the MAC address of E1 of the router
E.the MAC address of Switch 2
F.the MAC address of the email server
Correct:C
20.What is the default configuration register setting . most Cisco routers?
A.0x2210
B.0x2104
C.0x2102
D.0x2012
E.0x2142
Correct:C
21.drag drop

Correct:
Green choice1---->Yellow Choice5
Green choice2---->Yellow Choice2
Green choice3---->Yellow Choice4
Green choice4---->Yellow Choice3
Green choice5---->Yellow Choice1
22.Which statements accurately describe CDP? (Choose three.)
A.CDP is an IEEE standard protocol.
B.CDP is a Cisco proprietary protocol.
C.CDP is a datalink layer protocol.
D.CDP is a network layer protocol.
E.CDP can discover directly connected neighboring Cisco devices.
F.CDP can discover Cisco devices that are not directly connected.
Correct:B C E
23.drag drop

Correct:
Green choice1---->Yellow Choice2
Green choice2---->Yellow Choice1
Green choice4---->Yellow Choice3
Green choice6---->Yellow Choice4
Green choice5---->Yellow Choice5
24.Why is the show processes command used . a router before a debug command is entered?
A.to verify the IOS version that is running
B.to verify the amount of space in flash memory
C.to view the number of timers that are currently in use
D.to verify that the CPU utilization is low enough to handle the effects of a debug command
E.to check if the load meter file has enough space left to store the output of the debug command
Correct:D
25.lab

Correct:
26.drag drop

Correct:
Green choice4---->Yellow Choice1
Green choice3---->Yellow Choice2
Green choice6---->Yellow Choice3
Green choice2---->Yellow Choice4
Green choice5---->Yellow Choice5
27.Which of the following commands displays the configurable parameters and statistics of all interfaces . a router?
A.show running-config
B.show startup-config
C.show interfaces
D.show processes
E.show versions
Correct:C
28.Which types of cables are required to interconnect the devices shown in the graphic? (Choose three.)

A.V.35 cable
B.crossover cable
C.USB cable
D.RJ-11 cable
E.rollover cable
F.straight-through cable
Correct:B E F
29.Which statements are true regarding ICMP packets? (Choose two.)
A.They acknowledge receipt of TCP segments.
B.They guarantee datagram delivery.
C.They can provide hosts with information about network problems.
D.They are encapsulated within IP datagrams.
E.They are encapsulated within UDP datagrams.
Correct:C D
30.If NVRAM lacks boot system commands, where does the router look for the Cisco IOS by default?
A.ROM
B.RAM
C.Flash
D.bootstrap
E.startup-config
Correct:C