stm32 库函数(按键控制led灯闪烁)最简单易懂的使用方法

STM32 使用库函数(按键控制led不同的闪烁效果)

下面是main.c

#include "stm32f10x.h"
#include "led.h"`
#include "key.h"
int main(void)
	
{
while(1)
     {
        if(!GPIO_ReadInputDataBit(GPIOE,GPIO_Pin_3))
        {
           GPIO_WriteBit(GPIOE,GPIO_Pin_5,(BitAction)(1));
        }
        else
        {
           GPIO_WriteBit(GPIOE,GPIO_Pin_5,(BitAction)(0));
        }
     }
	
}

led.c

#include "led.h"


void LED_Init(void)
{
GPIO_InitTypeDef GPIO_InitStructure;//构造结构体 
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB,ENABLE);
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOE,ENABLE);//使能其所在时钟 
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_5;//定义IO端口 
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP;//定义IO端口输出模式 
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;//定义IO端口输出速度
GPIO_Init(GPIOE, &GPIO_InitStructure);//写入其中 
}

led.h

#ifndef _led_H

#include "stm32f10x.h"
#include "stm32f10x_gpio.h"






void LED_Init(void);

#endif

key.c

#include "key.h"

void KEY_Init(void)

{
    GPIO_InitTypeDef  GPIO_InitStructure; //构造结构体 
    RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOE,ENABLE);//使能其所在时钟        
    GPIO_InitStructure.GPIO_Pin = GPIO_Pin_3;//定义IO端口                       
    GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU;//上拉输入    
  
    GPIO_Init(GPIOE,&GPIO_InitStructure);      

}

key.h

#ifndef _led_H
#define _led_H

#include "stm32f10x.h"
#include "stm32f10x_gpio.h"
void KEY_Init(void);
#define KEYPORT GPIOE
#define KEY1    GPIO_Pin_3



#endif
  • 13
    点赞
  • 69
    收藏
    觉得还不错? 一键收藏
  • 6
    评论
以下是一个使用STM32库函数实现的按键中断控制LED的示例代码: ```c #include "stm32f10x.h" void GPIO_Configuration(void); void EXTI_Configuration(void); void NVIC_Configuration(void); int main(void) { GPIO_Configuration(); EXTI_Configuration(); NVIC_Configuration(); while (1) { // 循环等待按键中断 } } void GPIO_Configuration(void) { GPIO_InitTypeDef GPIO_InitStructure; // 打开GPIOB和GPIOC时钟 RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOB | RCC_APB2Periph_GPIOC, ENABLE); // 配置GPIOB.0为输入模式,上拉输入 GPIO_InitStructure.GPIO_Pin = GPIO_Pin_0; GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IPU; GPIO_Init(GPIOB, &GPIO_InitStructure); // 配置GPIOC.13为输出模式,推挽输出 GPIO_InitStructure.GPIO_Pin = GPIO_Pin_13; GPIO_InitStructure.GPIO_Mode = GPIO_Mode_Out_PP; GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; GPIO_Init(GPIOC, &GPIO_InitStructure); } void EXTI_Configuration(void) { EXTI_InitTypeDef EXTI_InitStructure; // 打开AFIO时钟 RCC_APB2PeriphClockCmd(RCC_APB2Periph_AFIO, ENABLE); // 将PB.0连接到EXTI线0上 GPIO_EXTILineConfig(GPIO_PortSourceGPIOB, GPIO_PinSource0); // 配置EXTI线0为中断模式,下降沿触发 EXTI_InitStructure.EXTI_Line = EXTI_Line0; EXTI_InitStructure.EXTI_Mode = EXTI_Mode_Interrupt; EXTI_InitStructure.EXTI_Trigger = EXTI_Trigger_Falling; EXTI_InitStructure.EXTI_LineCmd = ENABLE; EXTI_Init(&EXTI_InitStructure); } void NVIC_Configuration(void) { NVIC_InitTypeDef NVIC_InitStructure; // 配置EXTI线0的中断优先级为0 NVIC_InitStructure.NVIC_IRQChannel = EXTI0_IRQn; NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0; NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0; NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; NVIC_Init(&NVIC_InitStructure); } void EXTI0_IRQHandler(void) { if (EXTI_GetITStatus(EXTI_Line0) != RESET) { // 按键中断发生,切换LED状态 GPIOC->ODR ^= GPIO_Pin_13; // 清除中断标志位 EXTI_ClearITPendingBit(EXTI_Line0); } } ``` 在该示例代码中,我们使用GPIOB.0作为输入按键,GPIOC.13作为输出LED。在GPIO配置函数中,我们使用库函数来配置GPIOB.0为输入模式并开启上拉输入,GPIOC.13为推挽输出模式。在EXTI配置函数中,我们使用库函数将GPIOB.0连接到EXTI线0上,并配置EXTI线0为下降沿触发的中断模式。在NVIC配置函数中,我们配置了EXTI线0的中断优先级为0,并开启中断。在按键中断处理函数中,我们切换GPIOC.13的状态,并清除中断标志位。最后,在while循环中等待按键中断的发生。

“相关推荐”对你有帮助么?

  • 非常没帮助
  • 没帮助
  • 一般
  • 有帮助
  • 非常有帮助
提交
评论 6
添加红包

请填写红包祝福语或标题

红包个数最小为10个

红包金额最低5元

当前余额3.43前往充值 >
需支付:10.00
成就一亿技术人!
领取后你会自动成为博主和红包主的粉丝 规则
hope_wisdom
发出的红包
实付
使用余额支付
点击重新获取
扫码支付
钱包余额 0

抵扣说明:

1.余额是钱包充值的虚拟货币,按照1:1的比例进行支付金额的抵扣。
2.余额无法直接购买下载,可以购买VIP、付费专栏及课程。

余额充值