合宙PY32F103休眠STOP模式

PY32F030 SWD 在线烧录说明
先在程序进入 通迅脚恢复到GPIO 模式
无限复位
上电运行后
再次烧入正式程序
或者在代码进行上面循环操作

由正常程序烧录到复位程序时无需外部电源
直接用jlink 的5v 即可
h文档 源码

/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __MAIN_H
#define __MAIN_H

 #ifdef __cplusplus
extern "C" {
#endif

/* Includes ------------------------------------------------------------------*/
#include "py32f0xx_hal.h"
#include "py32f030xx_Start_Kit.h"

//LOW POWER
#define LPW_STOP 0x06
#define LPW_ISR2 0x1F	
#define LPW_ISR1 0x3F
#define LPW_ISR3 0x5F
#define LPW_ISR4 0x6F

#define SET_BIT_HIGH   0xFF	

//LED 管脚  
#define COM0_PORT_PIN  GPIO_PIN_15	
#define COM1_PORT_PIN  GPIO_PIN_3	
#define COM2_PORT_PIN  GPIO_PIN_4	
#define LEDW_PORT_PIN  GPIO_PIN_5
#define LEDY_PORT_PIN  GPIO_PIN_8

//休眠中断寄存器
#define ISR_KEY_REGISTER   EXTI4_15_IRQn
#define ISR_IR_REGISTER    EXTI4_15_IRQn

//CTR GPIO
#define BEEP_PORT_PIN   GPIO_PIN_14
#define SWING_PORT_PIN  GPIO_PIN_4
#define FANP_PORT_PIN   GPIO_PIN_2
#define IR_PORT_PIN     GPIO_PIN_1

//BAT
#define VDC_PORT_PIN    GPIO_PIN_12 

//功能开关标志
#define FUNC_STOP  0
#define IO_EN      1

//定时计数器
#define TIMER_CNT  3600

//状态切换控制
#define LAMP_STEP_W         0x1A	
#define LAMP_STEP_Y         0x1B
#define LAMP_STEP_MIX       0x1C
#define LAMP_STEP_STOP      0x1D
#define LAMP_STEP_STANDBY   0x1E

//FIX LOW POWER FLAG
extern unsigned char Lpwr_flag;	
extern LPTIM_HandleTypeDef LPTIMConf;	
extern GPIO_InitTypeDef    SEG_GPIO_Initure;
extern uint32_t            StartCalibration;

/* Private includes ----------------------------------------------------------*/
/* Private defines -----------------------------------------------------------*/
/* Exported variables prototypes ---------------------------------------------*/
/* Exported functions prototypes ---------------------------------------------*/
void APP_ErrorHandler(void);
extern void APP_ConfigureExti(void);
extern void Start_Init(void);
extern void Register_DeInit(void);

#ifdef __cplusplus
}
#endif

#endif /* __MAIN_H */



//Ó²¼þµÍµçƽ ÉèÖÃΪÏÂÀ­ÊäÈë
//Ó²¼þ¸ßµçƽ ÉèÖÃΪÉÏÀ­ÊäÈë
//Ðü¿Õ½Å     ÉèÖÃΪģÄâÊäÈë
void LPWR_GPIO_float(void)
{
     	GPIO_InitTypeDef  GPIO_InitStruct;
     	__HAL_RCC_GPIOF_CLK_ENABLE();         

            /* Enable GPIOA clock */
        	__HAL_RCC_GPIOB_CLK_ENABLE();        

              /* Enable GPIOA clock */
         	__HAL_RCC_GPIOA_CLK_ENABLE();        

                  /* Enable GPIOA clock */

	// -----------------------------------------------------beep
	GPIO_InitStruct.Pin   = GPIO_PIN_1 | GPIO_PIN_2| \
              	        GPIO_PIN_3 | GPIO_PIN_4| \
													GPIO_PIN_5 | GPIO_PIN_7| \
													GPIO_PIN_13 | GPIO_PIN_14| \
													GPIO_PIN_15;  //SWCLK
	GPIO_InitStruct.Mode  = GPIO_MODE_ANALOG;            /* Push-pull output */
	GPIO_InitStruct.Pull  = GPIO_NOPULL;                    /* Enable pull-up */
	GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;          /* GPIO speed */  

	/* GPIO Initialization */
	HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);      

	// -----------------------------------------------------beep
	GPIO_InitStruct.Pin   = GPIO_PIN_1 | GPIO_PIN_3| \
              	        GPIO_PIN_4 | GPIO_PIN_5| \
													GPIO_PIN_8;  
	GPIO_InitStruct.Mode  = GPIO_MODE_ANALOG;            /* Push-pull output */
	GPIO_InitStruct.Pull  = GPIO_NOPULL;                    /* Enable pull-up */
	GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;          /* GPIO speed */  

	/* GPIO Initialization */
	HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);  

	// -----------------------------------------------------beep
	GPIO_InitStruct.Pin   = GPIO_PIN_0 | GPIO_PIN_2;
	GPIO_InitStruct.Mode  = GPIO_MODE_ANALOG;            /* Push-pull output */
	GPIO_InitStruct.Pull  = GPIO_NOPULL;                    /* Enable pull-up */
	GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;          /* GPIO speed */  

	/* GPIO Initialization */
	HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);  
}

//20240522
 void APP_ConfigureExti(void)
{	
        LPWR_GPIO_float();

	__HAL_ADC_DISABLE(&AdcHandle);	
	
	/* ³õʼ»¯ÍⲿÖÐ¶Ï */
	GPIO_InitTypeDef  GPIO_InitStruct={0};

	__HAL_RCC_GPIOA_CLK_ENABLE();                  /* Enable GPIOA clock */
	__HAL_RCC_GPIOF_CLK_ENABLE();                  /* Enable GPIOA clock */	
	
	GPIO_InitStruct.Mode  = GPIO_MODE_IT_RISING_FALLING;  /* GPIO mode set to falling edge interrupt */
	GPIO_InitStruct.Pull  = GPIO_PULLUP;           /* Pull-up */
	GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;  /* High-speed */
	GPIO_InitStruct.Pin   = GPIO_PIN_6 | GPIO_PIN_12;
	HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
	
	//GPIO_MODE_EVT_RISING GPIO_MODE_INPUT
	GPIO_InitStruct.Mode  = GPIO_MODE_IT_RISING_FALLING;  /* GPIO mode set to falling edge interrupt */
	GPIO_InitStruct.Pull  = GPIO_PULLUP;           /* Pull-up */
	GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_LOW;  /* High-speed */
	GPIO_InitStruct.Alternate = GPIO_AF1_IR; 
	GPIO_InitStruct.Pin   = GPIO_PIN_1;
	HAL_GPIO_Init(GPIOF, &GPIO_InitStruct);		
	
	/* Enable EXTI interrupt */
	HAL_NVIC_EnableIRQ( EXTI4_15_IRQn );
	HAL_NVIC_EnableIRQ( EXTI0_1_IRQn );		

	/* Configure interrupt priority */
	HAL_NVIC_SetPriority(EXTI4_15_IRQn, 1, 1);
	HAL_NVIC_SetPriority(EXTI0_1_IRQn,  2, 2);		
						
	/* Suspend SysTick */
HAL_SuspendTick();
	
  APP_SystemClockConfig( RCC_HSICALIBRATION_8MHz );
										
	/* Enter STOP mode PWR_MAINREGULATOR_ON | PWR_LOWPOWERREGULATOR_ON*/
	HAL_PWR_EnterSTOPMode( PWR_LOWPOWERREGULATOR_ON, PWR_STOPENTRY_WFI );

	/* Resume the SysTick interrupt */
	HAL_ResumeTick(); 	
			
while( HAL_NVIC_GetPendingIRQ(EXTI0_1_IRQn) )
	{					
			__HAL_GPIO_EXTI_CLEAR_IT( GPIO_PIN_1 );		
	    NVIC_ClearPendingIRQ( EXTI0_1_IRQn );				
		  break;			
	}		
	
while( HAL_NVIC_GetPendingIRQ(EXTI4_15_IRQn) )
	{
			__HAL_GPIO_EXTI_CLEAR_IT( GPIO_PIN_6 | GPIO_PIN_12 );		
	    NVIC_ClearPendingIRQ( EXTI4_15_IRQn );				
		  break;
	}		
	
	Lpwr_flag = LPW_ISR1;
	HAL_TIM_PWM_DeInit(&Tim14Handle);
	HAL_TIM_PWM_DeInit(&Tim3Handle);		
	HAL_TIM_Base_DeInit(&Tim16Handle);	
	HAL_ADC_DeInit(&AdcHandle);			
}