个人记录之8266数据处理

个人记录，只想赚C币
#include “stm32f10x.h”
#include “bsp_usart1.h”
#include “bsp_SysTick.h”
#include “bsp_esp8266.h”
#include “test.h”
#include “bsp_dht11.h”
#include “bsp_led.h”
#include “bsp_beep.h”
#include <stdio.h>
#include <string.h>
#include <stdbool.h>

int main ( void )
{
uint8_t ucId, ucLen,z;
char cStr1 [ 100 ] = { 0 }, cCh;
char cStr2 [ 100 ] = { 0 },cStr3 [ 100 ] = { 0 }, cStr4 [ 100 ] = { 0 };
char buf1[]={0},buf2[50]={0},buf3[50]={0};
char * pCh, * pCh1;

USARTx_Config (); //初始化串口1
SysTick_Init (); //配置 SysTick 为 1ms 中断一次
ESP8266_Init (); //初始化WiFi模块使用的接口和外设
LED_Init ();
ESP8266_StaTcpClient_UnvarnishTest ();
while(1)
{
if ( strEsp8266_Fram_Record .InfBit .FramFinishFlag )
{
USART_ITConfig ( macESP8266_USARTx, USART_IT_RXNE, DISABLE );
strEsp8266_Fram_Record .Data_RX_BUF [ strEsp8266_Fram_Record .InfBit .FramLength ] = ‘\0’;

if ( ( ( pCh = strstr ( strEsp8266_Fram_Record .Data_RX_BUF, “<” ) ) != 0 ) &&
( ( pCh1 = strstr ( strEsp8266_Fram_Record .Data_RX_BUF, “>” ) ) != 0 ) )
{
if ( pCh < pCh1)
{
ucLen = pCh1-pCh+1;
memcpy ( cStr1, pCh, ucLen );
cStr1 [ ucLen ] = ‘\0’;
Usart_SendArray(macUSARTx,cStr1,strlen(cStr1)); //发送接收到的数据

		    sscanf(cStr1, "%*[^/]/%[^@]", buf1);  //buf1，cStr2为地址加参数	
				memcpy ( cStr2,buf1,strlen(buf1));    
				cStr2[strlen(buf1)] = '\0';    
	      Usart_SendArray(macUSARTx,cStr2,strlen(cStr2)); //发送cStr2的数据 地址加参数
				
				sscanf(buf1, "%*s%s",buf3);   //buf3为参数
				memcpy ( cStr3,buf3,strlen(buf3));    
				cStr3[strlen(buf3)] = '\0';    
	      Usart_SendArray(macUSARTx,cStr3,strlen(cStr3));	//发送参数 
				
				sscanf(buf1,"%[^, ]", buf2); //buf2为地址
				memcpy ( cStr4,buf2,strlen(buf2));    
				cStr4[strlen(buf2)] = '\0';    
	      Usart_SendArray(macUSARTx,cStr4,strlen(cStr4)); //发送地址
				
				macLED2_ON();
      Delay_ms(500);	
      macLED2_OFF();	
				 		}	 
  }	
   	strEsp8266_Fram_Record .InfBit .FramLength = 0;
    strEsp8266_Fram_Record .InfBit .FramFinishFlag = 0;			
		USART_ITConfig ( macESP8266_USARTx, USART_IT_RXNE, ENABLE ); //使能串口接收中断	
	}	

}
}