OSPF协议配置实验（二）！

OSPF与RIP混合配置实验

实验要求:
1、按图配置ospf区域
2、area1配置成stub区域，area3配置为nssa区域
3、R1做路由汇总
4、全网互通
各设备设置如下：
R1：

[R1]int g0/0/0
[R1-GigabitEthernet0/0/0]ip a 10.0.0.1 24
[R1-GigabitEthernet0/0/0]q
[R1]ospf 1 router-id 1.1.1.1	
[R1-ospf-1]area 4
[R1-ospf-1-area-0.0.0.4]network 10.0.0.0 0.0.0.255
[R1]int LoopBack 0
[R1-LoopBack0]ip a 192.168.1.1 24
[R1-LoopBack0]int LoopBack 1
[R1-LoopBack1]ip a 192.168.2.1 24
[R1-LoopBack1]int LoopBack 2
[R1-LoopBack2]ip a 192.168.3.1 24
[R1-LoopBack2]int LoopBack 3
[R1-LoopBack3]ip a 192.168.4.1 24
[R1-LoopBack3]int LoopBack 4
[R1-LoopBack4]ip a 192.168.5.1 24
[R1-LoopBack4]int LoopBack 5
[R1-LoopBack5]ip a 192.168.6.1 24
[R1-LoopBack5]int LoopBack 6
[R1-LoopBack6]ip a 192.168.7.1 24
[R1-LoopBack6]q
[R1]ospf 1
R1-ospf-1]area 4
[R1-ospf-1-area-0.0.0.4]network 192.168.0.0 0.0.255.255

R2

[Huawei]int g0/0/0
[Huawei-GigabitEthernet0/0/0]ip a 10.0.0.2 24
[Huawei-GigabitEthernet0/0/0]int g0/0/1
[Huawei-GigabitEthernet0/0/1]ip a 20.0.0.1 24
[Huawei-GigabitEthernet0/0/1]int g2/0/0
[Huawei-GigabitEthernet2/0/0]ip a 30.0.0.1 24
[R2]ospf 1	
[R2]ospf 1 router-id 2.2.2.2
[R2-ospf-1]area 4
[R2-ospf-1-area-0.0.0.4]network 10.0.0.0 0.0.0.255	
[R2-ospf-1-area-0.0.0.4]q
[R2-ospf-1]area 0
[R2-ospf-1-area-0.0.0.0]network 30.0.0.0 0.0.0.255
[R2-ospf-1-area-0.0.0.0]q
[R2-ospf-1]area 1
[R2-ospf-1-area-0.0.0.1]network 20.0.0.0 0.0.0.255
[R2]ospf 1
[R2-ospf-1]area 1
[R2-ospf-1-area-0.0.0.1]stub                             //设置末梢区域
[R2]ospf 1  
[R2-ospf-1]area 4
[R2-ospf-1-area-0.0.0.4]abr-summary 192.168.0.0 255.255.0.0

R3：

[R3]int loop	
[R3]int LoopBack 0
[R3-LoopBack0]ip a 3.3.3.3 32
[R3-LoopBack0]q
[R3]ospf 1 router-id 3.3.3.3
[R3-ospf-1]q
[R3]ospf 1
[R3-ospf-1]area 1
[R3-ospf-1-area-0.0.0.1]network 20.0.0.0 0.0.0.255
[R3]ospf 1
[R3-ospf-1]ar	
[R3-ospf-1]area 1
[R3-ospf-1-area-0.0.0.1]stub                             //设置末梢区域
[R3-ospf-1-area-0.0.0.1]q
[R3]int g0/0/0
[R3-GigabitEthernet0/0/0]ip a 20.0.0.2 24
[R3-GigabitEthernet0/0/0]q
[R3]ospf 1
[R3-ospf-1]area 1
[R3-ospf-1-area-0.0.0.1]network 3.0.0.0 0.255.255.255

R4：

[R4]int g0/0/0
[R4-GigabitEthernet0/0/0]ip a 30.0.0.2 24 
[R4-GigabitEthernet0/0/0]int g0/0/1
[R4-GigabitEthernet0/0/1]ip a 40.0.0.1 24
[R4-GigabitEthernet0/0/1]q
[R4]ospf 1 router-id 4.4.4.4
[R4-ospf-1]area 0
[R4-ospf-1-area-0.0.0.0]network 30.0.0.0 0.0.0.255               
[R4-ospf-1]area 2
[R4-ospf-1-area-0.0.0.2]network 40.0.0.0 0.0.0.255
[R4-ospf-1-area-0.0.0.2]vlink-peer 5.5.5.5                   //设置虚接口

R5：

[R5]int g0/0/0
[R5-GigabitEthernet0/0/0]ip a 40.0.0.2 24
[R5-GigabitEthernet0/0/0]int g0/0/1
[R5-GigabitEthernet0/0/1]ip a 50.0.0.1 24
[R5]ospf 1 router-id 5.5.5.5
[R5-ospf-1]area 2
[R5-ospf-1-area-0.0.0.2]network 40.0.0.0 0.0.0.255
[R5-ospf-1-area-0.0.0.2]q
[R5-ospf-1]area 3
[R5-ospf-1-area-0.0.0.3]network 50.0.0.0 0.0.0.255
[R5]ospf 1
[R5-ospf-1]area 2
[R5-ospf-1-area-0.0.0.2]vlink-peer 4.4.4.4                  //设置虚接口
[R5-ospf-1-area-0.0.0.2]q
[R5-ospf-1]area 3
[R5-ospf-1-area-0.0.0.3]nssa 

R6：

[R6]int g0/0/0
[R6-GigabitEthernet0/0/0]ip a 50.0.0.2 24
[R6-GigabitEthernet0/0/0]int g0/0/1
[R6-GigabitEthernet0/0/1]ip a 60.0.0.1 24
[R6-GigabitEthernet0/0/1]q
[R6]ospf 1 router-id 6.6.6.6
[R6-ospf-1]area 3
[R6-ospf-1-area-0.0.0.3]network 50.0.0.0 0.0.0.255
[R6-ospf-1-area-0.0.0.3]q
[R6-ospf-1]q
[R6]rip 1
[R6-rip-1]version 2
[R6-rip-1]network 60.0.0.0
[R6-rip-1]import-route ospf 1
[R6-rip-1]q
[R6]osp	
[R6]ospf 1
[R6-ospf-1]import-route rip 1
[R6]ospf 1
[R6-ospf-1]area 3
[R6-ospf-1-area-0.0.0.3]nssa 
[R6]ospf 1

R7：

[R7]int g0/0/0
[R7-GigabitEthernet0/0/0]ip a 60.0.0.2 24
[R7-GigabitEthernet0/0/0]int g0/0/1
[R7-GigabitEthernet0/0/1]ip a 100.0.0.254 24
[R7-GigabitEthernet0/0/1]q
[R7]rip 1	
[R7-rip-1]version 2
[R7-rip-1]network 60.0.0.0
[R7-rip-1]import-route direct 
[R7-rip-1] q
[R7]rip 1
[R7-rip-1]silent-interface g0/0/1                          //设置静默接口

实验结果：


在R2和R3的zrea1中设置末梢区域后查看lsdb表“dis ospf lscb”会发现只有1类2类和3类LSA

在R5和R6的zrea3中设置nssa后查看lsdb表会发现有1类、2类、3类和7类LSA