1、该拓扑为公司网络，其中包括公司总部、公司分部以及公司骨干网，不包含运营商公网部分。
2、设备名称均使用拓扑上名称改名，并且区分大小写。
3、整张拓扑均使用私网地址进行配置。
4、整张网络中，运行OSPF协议或者BGP协议的设备，其Router-id值为设备名数字号，例如R1的Router-id为1.1.1.1、
5、OSPF路由宣告部分选择接口宣告方式，例如192.168.100.1 0.0.0.0；BGP仅宣告用户网段。
6、IBGP部分使用环回建立邻居，EBGP部分使用直连链路建立邻居，所有运行BGP的设备都需要建立邻居。
7、R1、R2、R5、R6、R7、R8、R9、R10需要配置环回接口，环回接口IP为设备名数字号，掩码为32，例如R2的环回接口为2.2.2.2/32
8、所有PC的IP地址均手工配置。
公司分部：
1、PC5和PC6属于不同VLAN
2、SW4是一个二层交换机
3、SW3是一个三层交换机
4、R9是分部出口路由器
5、分部使用OSPF进程200达到分部网络全网可达
6、公司分部出口设备运行BGP协议连接骨干网络，AS号为100
7、因AS-PATH属性原因，总部与分部路由会学习不到，使用命令如（peer 10.10.10.10 allow-as-loop，仅在总部与分部设备上配置即可），将允许AS号重复。
公司总部：
1、交换机为二层交换机
2、PC1和PC2属于一个网段，PC3和PC4是一个网段
3、R3和R4分别是下方PC的网关路由器
4、为保障公司总部到骨干网络的连通性，公司总部使用双路由器双出口的方式接入骨干网
5、为保障公司总部网络内部具备负载，R1、R2、R3、R4设备均作为设备冗余，并使用全连接的方式进行路由选路
6、总部内网使用OSPF进程100达到全网可达，OSPF需要宣告环回。
7、公司总部双出口设备运行BGP协议连接骨干网络，AS号为100
8、因为R1和R2重发布时会出现次优路径，需要修改BGP路由优先级，使用命令（preference 140 255 255，仅在总部设备上配置即可），配置位置在iPv4-family unicast中。
公司骨干网：
1、为保障公司网络连通性，骨干网络考虑设备冗余操作，连接总部使用双路由器，骨干网络部分路由器之间使用双联路方式
2、骨干网设备运行OSPF协议达到骨干网全网可达，进程号为10。
3、骨干网设备运行BGP协议，AS号为200。使用全连接方式建邻。
优化：
1、为达到分流互备效果，公司总部业务部访问分部流量走R1，R2做备份；公司总部工程部访问分部流量走R2，R1做备份，并要求来回路径一致。
2、公司总部双出口流量均流向R5，R6做备份。来回路径一致。
3、OSPF重发布时，更改类型为Type-1
4、所有策略名称为policy-1
5、更改开销时，全部更改为10
接口列表：
骨干网区域：
AR5：
The device is running!
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys R5
[R5]int g 0/0/0
[R5-GigabitEthernet0/0/0]ip add 10.10.10.2 30
[R5-GigabitEthernet0/0/0]int g 0/0/1
[R5-GigabitEthernet0/0/1]ip add 10.10.10.10 30
[R5-GigabitEthernet0/0/1]int g 0/0/2
[R5-GigabitEthernet0/0/2]ip add 10.10.10.21 30
[R5-GigabitEthernet0/0/2]int g 1/0/0
[R5-GigabitEthernet1/0/0]ip add 10.10.10.17 30
[R5-GigabitEthernet1/0/0]qu
[R5]interface LoopBack 0
[R5-LoopBack0]ip add 5.5.5.5 32
[R5-LoopBack0]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R5]ospf 10 router-id 5.5.5.5
[R5-ospf-10]area 0
[R5-ospf-10-area-0.0.0.0]network 10.10.10.21 0.0.0.0
[R5-ospf-10-area-0.0.0.0]network 10.10.10.17 0.0.0.0
[R5-ospf-10-area-0.0.0.0]network 5.5.5.5 0.0.0.0
[R5-ospf-10-area-0.0.0.0]q
[R5-ospf-10]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R5]bgp 200
[R5-bgp]router-id 5.5.5.5
[R5-bgp]peer 10.10.10.1 as 100
[R5-bgp]peer 10.10.10.9 as 100
[R5-bgp]peer 6.6.6.6 as 200
[R5-bgp]peer 6.6.6.6 connect-interface LoopBack 0
[R5-bgp]peer 7.7.7.7 as 200
[R5-bgp]peer 7.7.7.7 connect-interface LoopBack 0
[R5-bgp]peer 8.8.8.8 as 200
[R5-bgp]peer 8.8.8.8 connect-interface LoopBack 0
[R5-bgp]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R5]bgp 200
[R5-bgp]peer 7.7.7.7 next-hop-local
[R5-bgp]peer 8.8.8.8 next-hop-local
[R5-bgp]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R5]q
<R5>save
The current configuration will be written to the device.
Are you sure to continue? (y/n)[n]:y
It will take several minutes to save configuration file, please wait.......
Configuration file had been saved successfully
Note: The configuration file will take effect after being activated
<R5>AR6：
The device is running!
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys R6
[R6]int g 0/0/0
[R6-GigabitEthernet0/0/0]ip add 10.10.10.14 30
[R6-GigabitEthernet0/0/0]int g 0/0/1
[R6-GigabitEthernet0/0/1]ip add 10.10.10.6 30
[R6-GigabitEthernet0/0/1]int g 0/0/2
[R6-GigabitEthernet0/0/2]ip add 10.10.10.25 30
[R6-GigabitEthernet0/0/2]int g 1/0/0
[R6-GigabitEthernet1/0/0]ip add 10.10.10.18 30
[R6-GigabitEthernet1/0/0]qu
[R6]interface LoopBack 0
[R6-LoopBack0]ip add 6.6.6.6 32
[R6-LoopBack0]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R6]ospf 10 router-id 6.6.6.6
[R6-ospf-10]area 0
[R6-ospf-10-area-0.0.0.0]network 10.10.10.25 0.0.0.0
[R6-ospf-10-area-0.0.0.0]network 10.10.10.18 0.0.0.0
[R6-ospf-10-area-0.0.0.0]network 6.6.6.6 0.0.0.0
[R6-ospf-10-area-0.0.0.0]q
[R6-ospf-10]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R6]bgp 200
[R6-bgp]router-id 6.6.6.6
[R6-bgp]peer 10.10.10.5 as 100
[R6-bgp]peer 10.10.10.13 as 100
[R6-bgp]peer 5.5.5.5 as 200
[R6-bgp]peer 5.5.5.5 connect-interface LoopBack 0
[R6-bgp]peer 7.7.7.7 as 200
[R6-bgp]peer 7.7.7.7 connect-interface LoopBack 0
[R6-bgp]peer 8.8.8.8 as 200
[R6-bgp]peer 8.8.8.8 connect-interface LoopBack 0
[R6-bgp]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R6]bgp 200
[R6-bgp]peer 7.7.7.7 next-hop-local
[R6-bgp]peer 8.8.8.8 next-hop-local
[R6-bgp]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R6]route-policy policy-1 permit node 10
Info: New Sequence of this List.
[R6-route-policy]apply cost 10
[R6-route-policy]q
[R6]route-policy policy-1 permit node 20
Info: New Sequence of this List.
[R6-route-policy]q
[R6]bgp 200
[R6-bgp]peer 10.10.10.5 route-policy policy-1 export
[R6-bgp]peer 10.10.10.13 route-policy policy-1 export
[R6-bgp]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R6]q
<R6>save
The current configuration will be written to the device.
Are you sure to continue? (y/n)[n]:y
It will take several minutes to save configuration file, please wait.......
Configuration file had been saved successfully
Note: The configuration file will take effect after being activated
<R6>AR7：
The device is running!
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys R7
[R7]int g 0/0/0
[R7-GigabitEthernet0/0/0]ip add 10.10.10.22 30
[R7-GigabitEthernet0/0/0]int g 0/0/1
[R7-GigabitEthernet0/0/1]ip add 10.10.10.26 30
[R7-GigabitEthernet0/0/1]int g 0/0/2
[R7-GigabitEthernet0/0/2]ip add 10.10.10.29 30
[R7-GigabitEthernet0/0/2]int g 1/0/0
[R7-GigabitEthernet1/0/0]ip add 10.10.10.33 30
[R7-GigabitEthernet1/0/0]qu
[R7]interface LoopBack 0
[R7-LoopBack0]ip add 7.7.7.7 32
[R7-LoopBack0]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R7]ospf 10 router-id 7.7.7.7
[R7-ospf-10]area 0
[R7-ospf-10-area-0.0.0.0]network 10.10.10.22 0.0.0.0
[R7-ospf-10-area-0.0.0.0]network 10.10.10.26 0.0.0.0
[R7-ospf-10-area-0.0.0.0]network 10.10.10.29 0.0.0.0
[R7-ospf-10-area-0.0.0.0]network 10.10.10.33 0.0.0.0
[R7-ospf-10-area-0.0.0.0]network 7.7.7.7 0.0.0.0
[R7-ospf-10-area-0.0.0.0]q
[R7-ospf-10]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R7]bgp 200
[R7-bgp]router-id 7.7.7.7
[R7-bgp]peer 5.5.5.5 as 200
[R7-bgp]peer 5.5.5.5 connect-interface LoopBack 0
[R7-bgp]peer 6.6.6.6 as 200
[R7-bgp]peer 6.6.6.6 connect-interface LoopBack 0
[R7-bgp]peer 8.8.8.8 as 200
[R7-bgp]peer 8.8.8.8 connect-interface LoopBack 0
[R7-bgp]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R7]q
<R7>save
The current configuration will be written to the device.
Are you sure to continue? (y/n)[n]:y
It will take several minutes to save configuration file, please wait.......
Configuration file had been saved successfully
Note: The configuration file will take effect after being activated
<R7>AR8：
The device is running!
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys R8
[R8]int g 0/0/0
[R8-GigabitEthernet0/0/0]ip add 10.10.10.30 30
[R8-GigabitEthernet0/0/0]int g 0/0/1
[R8-GigabitEthernet0/0/1]ip add 10.10.10.34 30
[R8-GigabitEthernet0/0/1]int g 0/0/2
[R8-GigabitEthernet0/0/2]ip add 10.10.10.37 30
[R8-GigabitEthernet0/0/2]qu
[R8]interface LoopBack 0
[R8-LoopBack0]ip add 8.8.8.8 32
[R8-LoopBack0]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R8]ospf 10 router-id 8.8.8.8
[R8-ospf-10]area 0
[R8-ospf-10-area-0.0.0.0]network 10.10.10.30 0.0.0.0
[R8-ospf-10-area-0.0.0.0]network 10.10.10.34 0.0.0.0
[R8-ospf-10-area-0.0.0.0]network 8.8.8.8 0.0.0.0
[R8-ospf-10-area-0.0.0.0]q
[R8-ospf-10]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R8]bgp 200
[R8-bgp]router-id 8.8.8.8
[R8-bgp]peer 7.7.7.7 as 200
[R8-bgp]peer 7.7.7.7 connect-interface LoopBack 0
[R8-bgp]peer 6.6.6.6 as 200
[R8-bgp]peer 6.6.6.6 connect-interface LoopBack 0
[R8-bgp]peer 5.5.5.5 as 200
[R8-bgp]peer 5.5.5.5 connect-interface LoopBack 0
[R8-bgp]peer 10.10.10.38 as 100
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R8-bgp]peer 5.5.5.5 next-hop-local
[R8-bgp]peer 6.6.6.6 next-hop-local
[R8-bgp]peer 7.7.7.7 next-hop-local
[R8-bgp]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R8]q
<R8>save
The current configuration will be written to the device.
Are you sure to continue? (y/n)[n]:y
It will take several minutes to save configuration file, please wait.......
Configuration file had been saved successfully
Note: The configuration file will take effect after being activated
<R8>企业内部总区域：
AR1
The device is running!
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys R1
[R1]interface GigabitEthernet 0/0/0
[R1-GigabitEthernet0/0/0]ip add 192.168.100.9 30
[R1-GigabitEthernet0/0/0]int g 0/0/1
[R1-GigabitEthernet0/0/1]ip add 10.10.10.41 30
[R1-GigabitEthernet0/0/1]int g 0/0/2
[R1-GigabitEthernet0/0/2]ip add 192.168.100.17 30
[R1-GigabitEthernet0/0/2]int g 1/0/0
[R1-GigabitEthernet1/0/0]ip add 10.10.10.1 30
[R1-GigabitEthernet1/0/0]int g 2/0/0
[R1-GigabitEthernet2/0/0]ip add 10.10.10.5 30
[R1-GigabitEthernet2/0/0]qu
[R1]interface LoopBack 0
[R1-LoopBack0]ip address 1.1.1.1 32
[R1-LoopBack0]qu
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R1]ospf 100 router-id 1.1.1.1
[R1-ospf-100]area 0
[R1-ospf-100-area-0.0.0.0]network 192.168.100.9 0.0.0.0
[R1-ospf-100-area-0.0.0.0]network 192.168.100.17 0.0.0.0
[R1-ospf-100-area-0.0.0.0]network 1.1.1.1 0.0.0.0
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R1]bgp 100
[R1-bgp]router-id 1.1.1.1
[R1-bgp]peer 2.2.2.2 as 100
[R1-bgp]peer 2.2.2.2 connect-interface LoopBack 0
[R1-bgp]peer 10.10.10.2 as 200
[R1-bgp]peer 10.10.10.6 as 200
[R1-bgp]qu
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R1]bgp 100
[R1-bgp]network 192.168.1.0 24
[R1-bgp]network 192.168.2.0 24
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R1-bgp]peer 10.10.10.2 allow-as-loop
[R1-bgp]peer 10.10.10.6 allow-as-loop
[R1-bgp]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R1]ospf 100
[R1-ospf-100]import-route bgp
[R1-ospf-100]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R1]bgp 100
[R1-bgp]ipv4-family unicast
[R1-bgp-af-ipv4]preference 140 255 255
[R1-bgp-af-ipv4]q
[R1-bgp]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R1]int g0/0/2
[R1-GigabitEthernet0/0/2]ospf cost 10
[R1-GigabitEthernet0/0/2]q
[R1]ospf 100
[R1-ospf-100]import-route bgp type 1
[R1-ospf-100]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R1]ip ip-prefix policy-1 permit 192.168.2.0 24
[R1]route-policy policy-1 permit node 10
Info: New Sequence of this List.
[R1-route-policy]if-match ip-prefix policy-1
[R1-route-policy]apply cost 10
[R1-route-policy]q
[R1]route-policy policy-1 permit node 20
Info: New Sequence of this List.
[R1-route-policy]q
[R1]bgp 100
[R1-bgp]peer 10.10.10.2 route-policy policy-1 export
[R1-bgp]peer 10.10.10.6 route-policy policy-1 export
[R1-bgp]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R1]q
<R1>save
The current configuration will be written to the device.
Are you sure to continue? (y/n)[n]:y
It will take several minutes to save configuration file, please wait.......
Configuration file had been saved successfully
Note: The configuration file will take effect after being activated
<R1>AR2：
The device is running!
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys R2
[R2]int g 0/0/0
[R2-GigabitEthernet0/0/0]ip add 192.168.100.13 30
[R2-GigabitEthernet0/0/0]int g 0/0/1
[R2-GigabitEthernet0/0/1]ip add 10.10.10.42 30
[R2-GigabitEthernet0/0/1]int g 0/0/2
[R2-GigabitEthernet0/0/2]ip add 192.168.100.5 30
[R2-GigabitEthernet0/0/2]int g 1/0/0
[R2-GigabitEthernet1/0/0]ip add 10.10.10.13 30
[R2-GigabitEthernet1/0/0]int g 2/0/0
[R2-GigabitEthernet2/0/0]ip add 10.10.10.9 30
[R2-GigabitEthernet2/0/0]qu
[R2]interface LoopBack 0
[R2-LoopBack0]ip address 2.2.2.2 32
[R2-LoopBack0]qu
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R2]ospf 100 router-id 2.2.2.2
[R2-ospf-100]area 0
[R2-ospf-100-area-0.0.0.0]network 192.168.100.13 0.0.0.0
[R2-ospf-100-area-0.0.0.0]network 192.168.100.5 0.0.0.0
[R2-ospf-100-area-0.0.0.0]network 2.2.2.2 0.0.0.0
[R2-ospf-100-area-0.0.0.0]q
[R2-ospf-100]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R2]bgp 100
[R2-bgp]router-id 2.2.2.2
[R2-bgp]peer 1.1.1.1 as 100
[R2-bgp]peer 1.1.1.1 connect-interface LoopBack 0
[R2-bgp]peer 10.10.10.10 as 200
[R2-bgp]peer 10.10.10.14 as 200
[R2-bgp]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R2]bgp 100
[R2-bgp]network 192.168.1.0 24
[R2-bgp]network 192.168.2.0 24
[R2-bgp]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R2]bgp 100
[R2-bgp]peer 10.10.10.10 allow-as-loop
[R2-bgp]peer 10.10.10.14 allow-as-loop
[R2-bgp]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R2]ospf 100
[R2-ospf-100]import-route bgp
[R2-ospf-100]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R2]bgp 100
[R2-bgp]ipv4-family unicast
[R2-bgp-af-ipv4]preference 140 255 255
[R2-bgp-af-ipv4]q
[R2-bgp]int g0/0/2
[R2-GigabitEthernet0/0/2]ospf cost 10
[R2-GigabitEthernet0/0/2]q
[R2]ospf 100
[R2-ospf-100]import-route bgp type 1
[R2-ospf-100]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R2]ip ip-prefix policy-1 permit 192.168.1.0 24
[R2]route-policy policy-1 permit node 10
Info: New Sequence of this List.
[R2-route-policy]if-match ip-prefix policy-1
[R2-route-policy]apply cost 10
[R2-route-policy]q
[R2]route-policy policy-1 permit node 20
Info: New Sequence of this List.
[R2-route-policy]q
[R2]bgp 100
[R2-bgp]peer 10.10.10.10 route-policy policy-1 export
[R2-bgp]peer 10.10.10.14 route-policy policy-1 export
[R2-bgp]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R2]q
<R2>save
The current configuration will be written to the device.
Are you sure to continue? (y/n)[n]:y
It will take several minutes to save configuration file, please wait.......
Configuration file had been saved successfully
Note: The configuration file will take effect after being activated
<R2>AR3：
The device is running!
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys R3
[R3]interface LoopBack 0
[R3-LoopBack0]ip address 3.3.3.3 32
[R3-LoopBack0]int g 0/0/0
[R3-GigabitEthernet0/0/0]ip add 192.168.100.10 30
[R3-GigabitEthernet0/0/0]int g 0/0/1
[R3-GigabitEthernet0/0/1]ip add 192.168.1.254 24
[R3-GigabitEthernet0/0/1]int g 0/0/2
[R3-GigabitEthernet0/0/2]ip add 192.168.100.1 30
[R3-GigabitEthernet0/0/2]int g 1/0/0
[R3-GigabitEthernet1/0/0]ip add 192.168.100.6 30
[R3-GigabitEthernet1/0/0]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R3]ospf 100 router-id 3.3.3.3
[R3-ospf-100]area 0
[R3-ospf-100-area-0.0.0.0]network 192.168.100.10 0.0.0.0
[R3-ospf-100-area-0.0.0.0]network 192.168.100.1 0.0.0.0
[R3-ospf-100-area-0.0.0.0]network 192.168.100.6 0.0.0.0
[R3-ospf-100-area-0.0.0.0]network 192.168.1.254 0.0.0.0
[R3-ospf-100-area-0.0.0.0]q
[R3-ospf-100]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R3]int g1/0/0
[R3-GigabitEthernet1/0/0]ospf cost 10
[R3-GigabitEthernet1/0/0]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R3]q
<R3>save
The current configuration will be written to the device.
Are you sure to continue? (y/n)[n]:y
It will take several minutes to save configuration file, please wait.......
Configuration file had been saved successfully
Note: The configuration file will take effect after being activated
<R3>AR4：
The device is running!
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys R4
[R4]interface LoopBack 0
[R4-LoopBack0]ip address 4.4.4.4 32
[R4-LoopBack0]int g 0/0/0
[R4-GigabitEthernet0/0/0]ip add 192.168.100.14 30
[R4-GigabitEthernet0/0/0]int g 0/0/1
[R4-GigabitEthernet0/0/1]ip add 192.168.2.254 24
[R4-GigabitEthernet0/0/1]int g 0/0/2
[R4-GigabitEthernet0/0/2]ip add 192.168.100.2 30
[R4-GigabitEthernet0/0/2]int g 1/0/0
[R4-GigabitEthernet1/0/0]ip add 192.168.100.18 30
[R4-GigabitEthernet1/0/0]qu
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R4]ospf 100 router-id 4.4.4.4
[R4-ospf-100]area 0
[R4-ospf-100-area-0.0.0.0]network 192.168.100.14 0.0.0.0
[R4-ospf-100-area-0.0.0.0]network 192.168.100.2 0.0.0.0
[R4-ospf-100-area-0.0.0.0]network 192.168.100.18 0.0.0.0
[R4-ospf-100-area-0.0.0.0]network 192.168.2.254 0.0.0.0
[R4-ospf-100-area-0.0.0.0]q
[R4-ospf-100]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R4]int g1/0/0
[R4-GigabitEthernet1/0/0]ospf cost 10
[R4-GigabitEthernet1/0/0]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R4]q
<R4>save
The current configuration will be written to the device.
Are you sure to continue? (y/n)[n]:y
It will take several minutes to save configuration file, please wait.......
Configuration file had been saved successfully
Note: The configuration file will take effect after being activated
<R4>LSW1：
The device is running!
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys SW1
[SW1]q
<SW1>save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]y
Now saving the current configuration to the slot 0.
Aug 4 2023 12:33:10-08:00 SW1 %%01CFM/4/SAVE(l)[1]:The user chose Y when decidi
ng whether to save the configuration to the device.
Save the configuration successfully.
<SW1>LSW2：
The device is running!
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys SW2
[SW2]q
<SW2>save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]y
Now saving the current configuration to the slot 0.
Aug 4 2023 12:33:16-08:00 SW2 %%01CFM/4/SAVE(l)[1]:The user chose Y when decidi
ng whether to save the configuration to the device.
Save the configuration successfully.
<SW2>PC1：
PC2：
PC3：
PC4：
企业分部网络区域：
AR9:
The device is running!
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys R9
[R9]interface LoopBack 0
[R9-LoopBack0]ip address 9.9.9.9 32
[R9-LoopBack0]int g 0/0/0
[R9-GigabitEthernet0/0/0]ip add 10.10.10.38 30
[R9-GigabitEthernet0/0/0]int g 0/0/1
[R9-GigabitEthernet0/0/1]ip add 192.168.200.2 30
[R9-GigabitEthernet0/0/1]qu
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R9]ospf 200 router-id 9.9.9.9
[R9-ospf-200]area 0
[R9-ospf-200-area-0.0.0.0]network 192.168.200.2 0.0.0.0
[R9-ospf-200-area-0.0.0.0]q
[R9-ospf-200]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R9]bgp 100
[R9-bgp]router-id 9.9.9.9
[R9-bgp]peer 10.10.10.37 as 200
[R9-bgp]network 192.168.3.0 24
[R9-bgp]network 192.168.4.0 24
[R9-bgp]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R9]bgp 100
[R9-bgp]peer 10.10.10.37 allow-as-loop
[R9-bgp]q
[R9]ospf 200
[R9-ospf-200]import-route bgp
[R9-ospf-200]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R9]ospf 200
[R9-ospf-200]import-route bgp type 1
[R9-ospf-200]q
[R9]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
<R9>save
The current configuration will be written to the device.
Are you sure to continue? (y/n)[n]:y
It will take several minutes to save configuration file, please wait.......
Configuration file had been saved successfully
Note: The configuration file will take effect after being activated
<R9>AR10:
The device is running!
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys R10
[R10]interface LoopBack 0
[R10-LoopBack0]ip address 10.10.10.10 32
[R10-LoopBack0]int g 0/0/0
[R10-GigabitEthernet0/0/0]ip address 192.168.200.1 30
[R10-GigabitEthernet0/0/0]int g0/0/1.1
[R10-GigabitEthernet0/0/1.1]ip address 192.168.3.254 24
[R10-GigabitEthernet0/0/1.1]dot1q termination vid 10
[R10-GigabitEthernet0/0/1.1]arp broadcast enable
[R10-GigabitEthernet0/0/1.1]int g0/0/1.2
[R10-GigabitEthernet0/0/1.2]ip address 192.168.4.254 24
[R10-GigabitEthernet0/0/1.2]dot1q termination vid 20
[R10-GigabitEthernet0/0/1.2]arp broadcast enable
[R10-GigabitEthernet0/0/1.2]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
[R10]ospf 200 router-id 10.10.10.10
[R10-ospf-200]area 0
[R10-ospf-200-area-0.0.0.0]network 192.168.3.254 0.0.0.0
[R10-ospf-200-area-0.0.0.0]network 192.168.4.254 0.0.0.0
[R10-ospf-200-area-0.0.0.0]network 192.168.200.1 0.0.0.0
[R10-ospf-200-area-0.0.0.0]q
[R10-ospf-200]q
[R10]q
=================================================================================================================================================================================
=================================================================================================================================================================================
=================================================================================================================================================================================
<R10>save
The current configuration will be written to the device.
Are you sure to continue? (y/n)[n]:y
It will take several minutes to save configuration file, please wait.......
Configuration file had been saved successfully
Note: The configuration file will take effect after being activated
<R10>LSW4:
The device is running!
<Huawei>sys
Enter system view, return user view with Ctrl+Z.
[Huawei]sys SW4
[SW4]vlan batch 10 20
Info: This operation may take a few seconds. Please wait for a moment...done.
[SW4]int g0/0/3
[SW4-GigabitEthernet0/0/3]port link-type access
[SW4-GigabitEthernet0/0/3]port default vlan 10
[SW4-GigabitEthernet0/0/3]int g0/0/2
[SW4-GigabitEthernet0/0/2]port link-type access
[SW4-GigabitEthernet0/0/2]port default vlan 20
[SW4-GigabitEthernet0/0/2]int g0/0/1
[SW4-GigabitEthernet0/0/1]port link-type trunk
[SW4-GigabitEthernet0/0/1]port trunk allow-pass vlan 10 20
[SW4-GigabitEthernet0/0/1]q
[SW4]q
<SW4>save
The current configuration will be written to the device.
Are you sure to continue?[Y/N]y
Now saving the current configuration to the slot 0.
Aug 4 2023 12:33:26-08:00 SW4 %%01CFM/4/SAVE(l)[5]:The user chose Y when decidi
ng whether to save the configuration to the device.
Save the configuration successfully.
<SW4>PC5:
PC6:
联通测试：
1、骨干网区域联通：
2、企业内部总区域联通：
3、企业分部网络区域联通：
4、企业内部总区域联通企业分部网络区域：
设备配置信息：
AR1：
<R1>display ip interface brief
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 7
The number of interface that is DOWN in Physical is 0
The number of interface that is UP in Protocol is 7
The number of interface that is DOWN in Protocol is 0
Interface IP Address/Mask Physical Protocol
GigabitEthernet0/0/0 192.168.100.9/30 up up
GigabitEthernet0/0/1 10.10.10.41/30 up up
GigabitEthernet0/0/2 192.168.100.17/30 up up
GigabitEthernet1/0/0 10.10.10.1/30 up up
GigabitEthernet2/0/0 10.10.10.5/30 up up
LoopBack0 1.1.1.1/32 up up(s)
NULL0 unassigned up up(s)
<R1>display ospf peer brief
OSPF Process 100 with Router ID 1.1.1.1
Peer Statistic Information
----------------------------------------------------------------------------
Area Id Interface Neighbor id State
0.0.0.0 GigabitEthernet0/0/0 3.3.3.3 Full
0.0.0.0 GigabitEthernet0/0/2 4.4.4.4 Full
----------------------------------------------------------------------------
<R1>display ospf lsdb
OSPF Process 100 with Router ID 1.1.1.1
Link State Database
Area: 0.0.0.0
Type LinkState ID AdvRouter Age Len Sequence Metric
Router 4.4.4.4 4.4.4.4 1739 72 80000012 1
Router 2.2.2.2 2.2.2.2 130 60 80000014 1
Router 1.1.1.1 1.1.1.1 1718 60 80000013 1
Router 3.3.3.3 3.3.3.3 145 72 80000015 1
Network 192.168.100.17 1.1.1.1 1423 32 80000009 0
Network 192.168.100.1 3.3.3.3 1445 32 80000009 0
Network 192.168.100.5 2.2.2.2 1537 32 80000009 0
Network 192.168.100.9 1.1.1.1 1551 32 80000009 0
Network 192.168.100.13 2.2.2.2 1467 32 80000009 0
AS External Database
Type LinkState ID AdvRouter Age Len Sequence Metric
External 192.168.4.0 1.1.1.1 1479 36 80000007 1
External 192.168.3.0 1.1.1.1 1479 36 80000007 1
External 192.168.4.0 2.2.2.2 1459 36 80000007 1
External 192.168.3.0 2.2.2.2 1459 36 80000007 1
<R1>display bgp peer
BGP local router ID : 1.1.1.1
Local AS number : 100
Total number of peers : 3 Peers in established state : 3
Peer V AS MsgRcvd MsgSent OutQ Up/Down State Pre
fRcv
2.2.2.2 4 100 224 226 0 03:38:24 Established
4
10.10.10.2 4 200 229 229 0 03:37:00 Established
4
10.10.10.6 4 200 230 226 0 03:34:23 Established
4
<R1>display bgp routing-table
BGP Local router ID is 1.1.1.1
Status codes: * - valid, > - best, d - damped,
h - history, i - internal, s - suppressed, S - Stale
Origin : i - IGP, e - EGP, ? - incomplete
Total Number of Routes: 14
Network NextHop MED LocPrf PrefVal Path/Ogn
*> 192.168.1.0 0.0.0.0 2 0 i
* i 2.2.2.2 3 100 0 i
* 10.10.10.2 0 200 100i
* 10.10.10.6 10 0 200 100i
*> 192.168.2.0 0.0.0.0 3 0 i
* i 2.2.2.2 2 100 0 i
* 10.10.10.2 0 200 100i
* 10.10.10.6 10 0 200 100i
*> 192.168.3.0 10.10.10.2 0 200 100i
* 10.10.10.6 10 0 200 100i
i 10.10.10.10 100 0 200 100i
*> 192.168.4.0 10.10.10.2 0 200 100i
* 10.10.10.6 10 0 200 100i
i 10.10.10.10 100 0 200 100i
<R1>display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 28 Routes : 28
Destination/Mask Proto Pre Cost Flags NextHop Interface
1.1.1.1/32 Direct 0 0 D 127.0.0.1 LoopBack0
2.2.2.2/32 OSPF 10 3 D 192.168.100.10 GigabitEthernet
0/0/0
10.10.10.0/30 Direct 0 0 D 10.10.10.1 GigabitEthernet
1/0/0
10.10.10.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
1/0/0
10.10.10.3/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
1/0/0
10.10.10.4/30 Direct 0 0 D 10.10.10.5 GigabitEthernet
2/0/0
10.10.10.5/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
2/0/0
10.10.10.7/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
2/0/0
10.10.10.40/30 Direct 0 0 D 10.10.10.41 GigabitEthernet
0/0/1
10.10.10.41/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
10.10.10.43/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
192.168.1.0/24 OSPF 10 2 D 192.168.100.10 GigabitEthernet
0/0/0
192.168.2.0/24 OSPF 10 3 D 192.168.100.10 GigabitEthernet
0/0/0
192.168.3.0/24 EBGP 140 0 D 10.10.10.2 GigabitEthernet
1/0/0
192.168.4.0/24 EBGP 140 0 D 10.10.10.2 GigabitEthernet
1/0/0
192.168.100.0/30 OSPF 10 2 D 192.168.100.10 GigabitEthernet
0/0/0
192.168.100.4/30 OSPF 10 11 D 192.168.100.10 GigabitEthernet
0/0/0
192.168.100.8/30 Direct 0 0 D 192.168.100.9 GigabitEthernet
0/0/0
192.168.100.9/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
192.168.100.11/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
192.168.100.12/30 OSPF 10 3 D 192.168.100.10 GigabitEthernet
0/0/0
192.168.100.16/30 Direct 0 0 D 192.168.100.17 GigabitEthernet
0/0/2
192.168.100.17/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
192.168.100.19/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
<R1>display current-configuration
[V200R003C00]
#
sysname R1
#
board add 0/1 1GEC
board add 0/2 1GEC
#
snmp-agent local-engineid 800007DB03000000000000
snmp-agent
#
clock timezone China-Standard-Time minus 08:00:00
#
portal local-server load portalpage.zip
#
drop illegal-mac alarm
#
set cpu-usage threshold 80 restore 75
#
aaa
authentication-scheme default
authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password cipher %$%$K8m.Nt84DZ}e#<0`8bmE3Uw}%$%$
local-user admin service-type http
#
firewall zone Local
priority 15
#
interface GigabitEthernet0/0/0
ip address 192.168.100.9 255.255.255.252
#
interface GigabitEthernet0/0/1
ip address 10.10.10.41 255.255.255.252
#
interface GigabitEthernet0/0/2
ip address 192.168.100.17 255.255.255.252
ospf cost 10
#
interface GigabitEthernet1/0/0
ip address 10.10.10.1 255.255.255.252
#
interface GigabitEthernet2/0/0
ip address 10.10.10.5 255.255.255.252
#
interface NULL0
#
interface LoopBack0
ip address 1.1.1.1 255.255.255.255
#
bgp 100
router-id 1.1.1.1
peer 2.2.2.2 as-number 100
peer 2.2.2.2 connect-interface LoopBack0
peer 10.10.10.2 as-number 200
peer 10.10.10.6 as-number 200
#
ipv4-family unicast
undo synchronization
preference 140 255 255
network 192.168.1.0
network 192.168.2.0
peer 2.2.2.2 enable
peer 10.10.10.2 enable
peer 10.10.10.2 route-policy policy-1 export
peer 10.10.10.2 allow-as-loop
peer 10.10.10.6 enable
peer 10.10.10.6 route-policy policy-1 export
peer 10.10.10.6 allow-as-loop
#
ospf 100 router-id 1.1.1.1
import-route bgp type 1
area 0.0.0.0
network 1.1.1.1 0.0.0.0
network 192.168.100.9 0.0.0.0
network 192.168.100.17 0.0.0.0
#
route-policy policy-1 permit node 10
if-match ip-prefix policy-1
apply cost 10
#
route-policy policy-1 permit node 20
#
ip ip-prefix policy-1 index 10 permit 192.168.2.0 24
#
user-interface con 0
authentication-mode password
user-interface vty 0 4
user-interface vty 16 20
#
wlan ac
#
return
<R1> AR2：
<R2>display ip interface brief
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 7
The number of interface that is DOWN in Physical is 0
The number of interface that is UP in Protocol is 7
The number of interface that is DOWN in Protocol is 0
Interface IP Address/Mask Physical Protocol
GigabitEthernet0/0/0 192.168.100.13/30 up up
GigabitEthernet0/0/1 10.10.10.42/30 up up
GigabitEthernet0/0/2 192.168.100.5/30 up up
GigabitEthernet1/0/0 10.10.10.13/30 up up
GigabitEthernet2/0/0 10.10.10.9/30 up up
LoopBack0 2.2.2.2/32 up up(s)
NULL0 unassigned up up(s)
<R2>display ospf peer brief
OSPF Process 100 with Router ID 2.2.2.2
Peer Statistic Information
----------------------------------------------------------------------------
Area Id Interface Neighbor id State
0.0.0.0 GigabitEthernet0/0/0 4.4.4.4 Full
0.0.0.0 GigabitEthernet0/0/2 3.3.3.3 Full
----------------------------------------------------------------------------
<R2>display ospf lsdb
OSPF Process 100 with Router ID 2.2.2.2
Link State Database
Area: 0.0.0.0
Type LinkState ID AdvRouter Age Len Sequence Metric
Router 4.4.4.4 4.4.4.4 481 72 80000013 1
Router 2.2.2.2 2.2.2.2 670 60 80000014 1
Router 1.1.1.1 1.1.1.1 462 60 80000014 1
Router 3.3.3.3 3.3.3.3 687 72 80000015 1
Network 192.168.100.17 1.1.1.1 167 32 8000000A 0
Network 192.168.100.1 3.3.3.3 187 32 8000000A 0
Network 192.168.100.5 2.2.2.2 277 32 8000000A 0
Network 192.168.100.9 1.1.1.1 295 32 8000000A 0
Network 192.168.100.13 2.2.2.2 207 32 8000000A 0
AS External Database
Type LinkState ID AdvRouter Age Len Sequence Metric
External 192.168.4.0 2.2.2.2 199 36 80000008 1
External 192.168.3.0 2.2.2.2 199 36 80000008 1
External 192.168.4.0 1.1.1.1 223 36 80000008 1
External 192.168.3.0 1.1.1.1 223 36 80000008 1
<R2>display bgp peer
BGP local router ID : 2.2.2.2
Local AS number : 100
Total number of peers : 3 Peers in established state : 3
Peer V AS MsgRcvd MsgSent OutQ Up/Down State Pre
fRcv
1.1.1.1 4 100 233 233 0 03:47:27 Established
4
10.10.10.10 4 200 237 239 0 03:45:55 Established
4
10.10.10.14 4 200 240 237 0 03:43:22 Established
4
<R2>display bgp routing-table
BGP Local router ID is 2.2.2.2
Status codes: * - valid, > - best, d - damped,
h - history, i - internal, s - suppressed, S - Stale
Origin : i - IGP, e - EGP, ? - incomplete
Total Number of Routes: 14
Network NextHop MED LocPrf PrefVal Path/Ogn
*> 192.168.1.0 0.0.0.0 3 0 i
* i 1.1.1.1 2 100 0 i
* 10.10.10.10 0 200 100i
* 10.10.10.14 10 0 200 100i
*> 192.168.2.0 0.0.0.0 2 0 i
* i 1.1.1.1 3 100 0 i
* 10.10.10.10 0 200 100i
* 10.10.10.14 10 0 200 100i
*> 192.168.3.0 10.10.10.10 0 200 100i
* 10.10.10.14 10 0 200 100i
i 10.10.10.2 100 0 200 100i
*> 192.168.4.0 10.10.10.10 0 200 100i
* 10.10.10.14 10 0 200 100i
i 10.10.10.2 100 0 200 100i
<R2>display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 28 Routes : 28
Destination/Mask Proto Pre Cost Flags NextHop Interface
1.1.1.1/32 OSPF 10 3 D 192.168.100.14 GigabitEthernet
0/0/0
2.2.2.2/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.10.10.8/30 Direct 0 0 D 10.10.10.9 GigabitEthernet
2/0/0
10.10.10.9/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
2/0/0
10.10.10.11/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
2/0/0
10.10.10.12/30 Direct 0 0 D 10.10.10.13 GigabitEthernet
1/0/0
10.10.10.13/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
1/0/0
10.10.10.15/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
1/0/0
10.10.10.40/30 Direct 0 0 D 10.10.10.42 GigabitEthernet
0/0/1
10.10.10.42/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
10.10.10.43/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
192.168.1.0/24 OSPF 10 3 D 192.168.100.14 GigabitEthernet
0/0/0
192.168.2.0/24 OSPF 10 2 D 192.168.100.14 GigabitEthernet
0/0/0
192.168.3.0/24 EBGP 140 0 D 10.10.10.10 GigabitEthernet
2/0/0
192.168.4.0/24 EBGP 140 0 D 10.10.10.10 GigabitEthernet
2/0/0
192.168.100.0/30 OSPF 10 2 D 192.168.100.14 GigabitEthernet
0/0/0
192.168.100.4/30 Direct 0 0 D 192.168.100.5 GigabitEthernet
0/0/2
192.168.100.5/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
192.168.100.7/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
192.168.100.8/30 OSPF 10 3 D 192.168.100.14 GigabitEthernet
0/0/0
192.168.100.12/30 Direct 0 0 D 192.168.100.13 GigabitEthernet
0/0/0
192.168.100.13/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
192.168.100.15/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
192.168.100.16/30 OSPF 10 11 D 192.168.100.14 GigabitEthernet
0/0/0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
<R2>display current-configuration
[V200R003C00]
#
sysname R2
#
board add 0/1 1GEC
board add 0/2 1GEC
#
snmp-agent local-engineid 800007DB03000000000000
snmp-agent
#
clock timezone China-Standard-Time minus 08:00:00
#
portal local-server load portalpage.zip
#
drop illegal-mac alarm
#
set cpu-usage threshold 80 restore 75
#
aaa
authentication-scheme default
authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password cipher %$%$K8m.Nt84DZ}e#<0`8bmE3Uw}%$%$
local-user admin service-type http
#
firewall zone Local
priority 15
#
interface GigabitEthernet0/0/0
ip address 192.168.100.13 255.255.255.252
#
interface GigabitEthernet0/0/1
ip address 10.10.10.42 255.255.255.252
#
interface GigabitEthernet0/0/2
ip address 192.168.100.5 255.255.255.252
ospf cost 10
#
interface GigabitEthernet1/0/0
ip address 10.10.10.13 255.255.255.252
#
interface GigabitEthernet2/0/0
ip address 10.10.10.9 255.255.255.252
#
interface NULL0
#
interface LoopBack0
ip address 2.2.2.2 255.255.255.255
#
bgp 100
router-id 2.2.2.2
peer 1.1.1.1 as-number 100
peer 1.1.1.1 connect-interface LoopBack0
peer 10.10.10.10 as-number 200
peer 10.10.10.14 as-number 200
#
ipv4-family unicast
undo synchronization
preference 140 255 255
network 192.168.1.0
network 192.168.2.0
peer 1.1.1.1 enable
peer 10.10.10.10 enable
peer 10.10.10.10 route-policy policy-1 export
peer 10.10.10.10 allow-as-loop
peer 10.10.10.14 enable
peer 10.10.10.14 route-policy policy-1 export
peer 10.10.10.14 allow-as-loop
#
ospf 100 router-id 2.2.2.2
import-route bgp type 1
area 0.0.0.0
network 2.2.2.2 0.0.0.0
network 192.168.100.5 0.0.0.0
network 192.168.100.13 0.0.0.0
#
route-policy policy-1 permit node 10
if-match ip-prefix policy-1
apply cost 10
#
route-policy policy-1 permit node 20
#
ip ip-prefix policy-1 index 10 permit 192.168.1.0 24
#
user-interface con 0
authentication-mode password
user-interface vty 0 4
user-interface vty 16 20
#
wlan ac
#
return
<R2> AR3：
<R3>display ip interface brief
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 5
The number of interface that is DOWN in Physical is 0
The number of interface that is UP in Protocol is 5
The number of interface that is DOWN in Protocol is 0
Interface IP Address/Mask Physical Protocol
GigabitEthernet0/0/0 192.168.100.10/30 up up
GigabitEthernet0/0/1 192.168.1.254/24 up up
GigabitEthernet0/0/2 192.168.100.1/30 up up
GigabitEthernet1/0/0 192.168.100.6/30 up up
NULL0 unassigned up up(s)
<R3>display ospf peer brief
OSPF Process 100 with Router ID 3.3.3.3
Peer Statistic Information
----------------------------------------------------------------------------
Area Id Interface Neighbor id State
0.0.0.0 GigabitEthernet0/0/0 1.1.1.1 Full
0.0.0.0 GigabitEthernet0/0/2 4.4.4.4 Full
0.0.0.0 GigabitEthernet1/0/0 2.2.2.2 Full
----------------------------------------------------------------------------
<R3>display ospf lsdb
OSPF Process 100 with Router ID 3.3.3.3
Link State Database
Area: 0.0.0.0
Type LinkState ID AdvRouter Age Len Sequence Metric
Router 4.4.4.4 4.4.4.4 605 72 80000013 1
Router 2.2.2.2 2.2.2.2 795 60 80000014 1
Router 1.1.1.1 1.1.1.1 585 60 80000014 1
Router 3.3.3.3 3.3.3.3 810 72 80000015 1
Network 192.168.100.17 1.1.1.1 290 32 8000000A 0
Network 192.168.100.1 3.3.3.3 310 32 8000000A 0
Network 192.168.100.5 2.2.2.2 402 32 8000000A 0
Network 192.168.100.9 1.1.1.1 418 32 8000000A 0
Network 192.168.100.13 2.2.2.2 332 32 8000000A 0
AS External Database
Type LinkState ID AdvRouter Age Len Sequence Metric
External 192.168.4.0 1.1.1.1 346 36 80000008 1
External 192.168.4.0 2.2.2.2 324 36 80000008 1
External 192.168.3.0 1.1.1.1 346 36 80000008 1
External 192.168.3.0 2.2.2.2 324 36 80000008 1
<R3>display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 23 Routes : 24
Destination/Mask Proto Pre Cost Flags NextHop Interface
1.1.1.1/32 OSPF 10 1 D 192.168.100.9 GigabitEthernet
0/0/0
2.2.2.2/32 OSPF 10 2 D 192.168.100.2 GigabitEthernet
0/0/2
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
192.168.1.0/24 Direct 0 0 D 192.168.1.254 GigabitEthernet
0/0/1
192.168.1.254/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
192.168.1.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
192.168.2.0/24 OSPF 10 2 D 192.168.100.2 GigabitEthernet
0/0/2
192.168.3.0/24 O_ASE 150 2 D 192.168.100.9 GigabitEthernet
0/0/0
192.168.4.0/24 O_ASE 150 2 D 192.168.100.9 GigabitEthernet
0/0/0
192.168.100.0/30 Direct 0 0 D 192.168.100.1 GigabitEthernet
0/0/2
192.168.100.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
192.168.100.3/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
192.168.100.4/30 Direct 0 0 D 192.168.100.6 GigabitEthernet
1/0/0
192.168.100.6/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
1/0/0
192.168.100.7/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
1/0/0
192.168.100.8/30 Direct 0 0 D 192.168.100.10 GigabitEthernet
0/0/0
192.168.100.10/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
192.168.100.11/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
192.168.100.12/30 OSPF 10 2 D 192.168.100.2 GigabitEthernet
0/0/2
192.168.100.16/30 OSPF 10 11 D 192.168.100.9 GigabitEthernet
0/0/0
OSPF 10 11 D 192.168.100.2 GigabitEthernet
0/0/2
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
<R3>display current-configuration
[V200R003C00]
#
sysname R3
#
board add 0/1 1GEC
#
snmp-agent local-engineid 800007DB03000000000000
snmp-agent
#
clock timezone China-Standard-Time minus 08:00:00
#
portal local-server load portalpage.zip
#
drop illegal-mac alarm
#
set cpu-usage threshold 80 restore 75
#
aaa
authentication-scheme default
authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password cipher %$%$K8m.Nt84DZ}e#<0`8bmE3Uw}%$%$
local-user admin service-type http
#
firewall zone Local
priority 15
#
interface GigabitEthernet0/0/0
ip address 192.168.100.10 255.255.255.252
#
interface GigabitEthernet0/0/1
ip address 192.168.1.254 255.255.255.0
#
interface GigabitEthernet0/0/2
ip address 192.168.100.1 255.255.255.252
#
interface GigabitEthernet1/0/0
ip address 192.168.100.6 255.255.255.252
ospf cost 10
#
interface NULL0
#
ospf 100 router-id 3.3.3.3
area 0.0.0.0
network 192.168.1.254 0.0.0.0
network 192.168.100.1 0.0.0.0
network 192.168.100.6 0.0.0.0
network 192.168.100.10 0.0.0.0
#
user-interface con 0
authentication-mode password
user-interface vty 0 4
user-interface vty 16 20
#
wlan ac
#
return
<R3> AR4：
<R4>display ip interface brief
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 5
The number of interface that is DOWN in Physical is 0
The number of interface that is UP in Protocol is 5
The number of interface that is DOWN in Protocol is 0
Interface IP Address/Mask Physical Protocol
GigabitEthernet0/0/0 192.168.100.14/30 up up
GigabitEthernet0/0/1 192.168.2.254/24 up up
GigabitEthernet0/0/2 192.168.100.2/30 up up
GigabitEthernet1/0/0 192.168.100.18/30 up up
NULL0 unassigned up up(s)
<R4>display ospf peer brief
OSPF Process 100 with Router ID 4.4.4.4
Peer Statistic Information
----------------------------------------------------------------------------
Area Id Interface Neighbor id State
0.0.0.0 GigabitEthernet0/0/0 2.2.2.2 Full
0.0.0.0 GigabitEthernet0/0/2 3.3.3.3 Full
0.0.0.0 GigabitEthernet1/0/0 1.1.1.1 Full
----------------------------------------------------------------------------
<R4>display ospf lsdb
OSPF Process 100 with Router ID 4.4.4.4
Link State Database
Area: 0.0.0.0
Type LinkState ID AdvRouter Age Len Sequence Metric
Router 4.4.4.4 4.4.4.4 710 72 80000013 1
Router 2.2.2.2 2.2.2.2 901 60 80000014 1
Router 1.1.1.1 1.1.1.1 691 60 80000014 1
Router 3.3.3.3 3.3.3.3 917 72 80000015 1
Network 192.168.100.17 1.1.1.1 397 32 8000000A 0
Network 192.168.100.1 3.3.3.3 417 32 8000000A 0
Network 192.168.100.5 2.2.2.2 508 32 8000000A 0
Network 192.168.100.9 1.1.1.1 524 32 8000000A 0
Network 192.168.100.13 2.2.2.2 438 32 8000000A 0
AS External Database
Type LinkState ID AdvRouter Age Len Sequence Metric
External 192.168.4.0 1.1.1.1 452 36 80000008 1
External 192.168.4.0 2.2.2.2 430 36 80000008 1
External 192.168.3.0 1.1.1.1 452 36 80000008 1
External 192.168.3.0 2.2.2.2 430 36 80000008 1
<R4>display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 23 Routes : 24
Destination/Mask Proto Pre Cost Flags NextHop Interface
1.1.1.1/32 OSPF 10 2 D 192.168.100.1 GigabitEthernet
0/0/2
2.2.2.2/32 OSPF 10 1 D 192.168.100.13 GigabitEthernet
0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
192.168.1.0/24 OSPF 10 2 D 192.168.100.1 GigabitEthernet
0/0/2
192.168.2.0/24 Direct 0 0 D 192.168.2.254 GigabitEthernet
0/0/1
192.168.2.254/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
192.168.2.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
192.168.3.0/24 O_ASE 150 2 D 192.168.100.13 GigabitEthernet
0/0/0
192.168.4.0/24 O_ASE 150 2 D 192.168.100.13 GigabitEthernet
0/0/0
192.168.100.0/30 Direct 0 0 D 192.168.100.2 GigabitEthernet
0/0/2
192.168.100.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
192.168.100.3/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
192.168.100.4/30 OSPF 10 11 D 192.168.100.13 GigabitEthernet
0/0/0
OSPF 10 11 D 192.168.100.1 GigabitEthernet
0/0/2
192.168.100.8/30 OSPF 10 2 D 192.168.100.1 GigabitEthernet
0/0/2
192.168.100.12/30 Direct 0 0 D 192.168.100.14 GigabitEthernet
0/0/0
192.168.100.14/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
192.168.100.15/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
192.168.100.16/30 Direct 0 0 D 192.168.100.18 GigabitEthernet
1/0/0
192.168.100.18/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
1/0/0
192.168.100.19/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
1/0/0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
<R4>display current-configuration
[V200R003C00]
#
sysname R4
#
board add 0/1 1GEC
#
snmp-agent local-engineid 800007DB03000000000000
snmp-agent
#
clock timezone China-Standard-Time minus 08:00:00
#
portal local-server load portalpage.zip
#
drop illegal-mac alarm
#
set cpu-usage threshold 80 restore 75
#
aaa
authentication-scheme default
authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password cipher %$%$K8m.Nt84DZ}e#<0`8bmE3Uw}%$%$
local-user admin service-type http
#
firewall zone Local
priority 15
#
interface GigabitEthernet0/0/0
ip address 192.168.100.14 255.255.255.252
#
interface GigabitEthernet0/0/1
ip address 192.168.2.254 255.255.255.0
#
interface GigabitEthernet0/0/2
ip address 192.168.100.2 255.255.255.252
#
interface GigabitEthernet1/0/0
ip address 192.168.100.18 255.255.255.252
ospf cost 10
#
interface NULL0
#
ospf 100 router-id 4.4.4.4
area 0.0.0.0
network 192.168.2.254 0.0.0.0
network 192.168.100.2 0.0.0.0
network 192.168.100.14 0.0.0.0
network 192.168.100.18 0.0.0.0
#
user-interface con 0
authentication-mode password
user-interface vty 0 4
user-interface vty 16 20
#
wlan ac
#
return
<R4> AR5：
<R5>display ip interface brief
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 6
The number of interface that is DOWN in Physical is 0
The number of interface that is UP in Protocol is 6
The number of interface that is DOWN in Protocol is 0
Interface IP Address/Mask Physical Protocol
GigabitEthernet0/0/0 10.10.10.2/30 up up
GigabitEthernet0/0/1 10.10.10.10/30 up up
GigabitEthernet0/0/2 10.10.10.21/30 up up
GigabitEthernet1/0/0 10.10.10.17/30 up up
LoopBack0 5.5.5.5/32 up up(s)
NULL0 unassigned up up(s)
<R5>display ospf peer brief
OSPF Process 10 with Router ID 5.5.5.5
Peer Statistic Information
----------------------------------------------------------------------------
Area Id Interface Neighbor id State
0.0.0.0 GigabitEthernet0/0/2 7.7.7.7 Full
0.0.0.0 GigabitEthernet1/0/0 6.6.6.6 Full
----------------------------------------------------------------------------
<R5>display ospf lsdb
OSPF Process 10 with Router ID 5.5.5.5
Link State Database
Area: 0.0.0.0
Type LinkState ID AdvRouter Age Len Sequence Metric
Router 7.7.7.7 7.7.7.7 10 84 80000016 1
Router 6.6.6.6 6.6.6.6 108 60 80000011 1
Router 8.8.8.8 8.8.8.8 1781 48 8000000C 1
Router 5.5.5.5 5.5.5.5 118 60 80000013 1
Network 10.10.10.17 5.5.5.5 248 32 8000000A 0
Network 10.10.10.21 5.5.5.5 118 32 8000000A 0
Network 10.10.10.25 6.6.6.6 108 32 8000000A 0
Network 10.10.10.29 7.7.7.7 10 32 8000000A 0
<R5>display bgp peer
BGP local router ID : 5.5.5.5
Local AS number : 200
Total number of peers : 5 Peers in established state : 5
Peer V AS MsgRcvd MsgSent OutQ Up/Down State Pre
fRcv
6.6.6.6 4 200 245 247 0 03:56:14 Established
2
7.7.7.7 4 200 236 246 0 03:54:21 Established
0
8.8.8.8 4 200 237 243 0 03:51:44 Established
2
10.10.10.1 4 100 250 251 0 03:59:20 Established
2
10.10.10.9 4 100 252 251 0 03:59:11 Established
2
<R5>display bgp routing-table
BGP Local router ID is 5.5.5.5
Status codes: * - valid, > - best, d - damped,
h - history, i - internal, s - suppressed, S - Stale
Origin : i - IGP, e - EGP, ? - incomplete
Total Number of Routes: 8
Network NextHop MED LocPrf PrefVal Path/Ogn
*> 192.168.1.0 10.10.10.1 2 0 100i
* 10.10.10.9 10 0 100i
i 10.10.10.5 2 100 0 100i
*> 192.168.2.0 10.10.10.9 2 0 100i
* 10.10.10.1 10 0 100i
i 10.10.10.13 2 100 0 100i
*>i 192.168.3.0 8.8.8.8 2 100 0 100i
*>i 192.168.4.0 8.8.8.8 2 100 0 100i
<R5>display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 27 Routes : 28
Destination/Mask Proto Pre Cost Flags NextHop Interface
5.5.5.5/32 Direct 0 0 D 127.0.0.1 LoopBack0
6.6.6.6/32 OSPF 10 1 D 10.10.10.18 GigabitEthernet
1/0/0
7.7.7.7/32 OSPF 10 1 D 10.10.10.22 GigabitEthernet
0/0/2
8.8.8.8/32 OSPF 10 2 D 10.10.10.22 GigabitEthernet
0/0/2
10.10.10.0/30 Direct 0 0 D 10.10.10.2 GigabitEthernet
0/0/0
10.10.10.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
10.10.10.3/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
10.10.10.8/30 Direct 0 0 D 10.10.10.10 GigabitEthernet
0/0/1
10.10.10.10/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
10.10.10.11/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
10.10.10.16/30 Direct 0 0 D 10.10.10.17 GigabitEthernet
1/0/0
10.10.10.17/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
1/0/0
10.10.10.19/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
1/0/0
10.10.10.20/30 Direct 0 0 D 10.10.10.21 GigabitEthernet
0/0/2
10.10.10.21/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
10.10.10.23/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
10.10.10.24/30 OSPF 10 2 D 10.10.10.18 GigabitEthernet
1/0/0
OSPF 10 2 D 10.10.10.22 GigabitEthernet
0/0/2
10.10.10.28/30 OSPF 10 2 D 10.10.10.22 GigabitEthernet
0/0/2
10.10.10.32/30 OSPF 10 2 D 10.10.10.22 GigabitEthernet
0/0/2
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
192.168.1.0/24 EBGP 255 2 D 10.10.10.1 GigabitEthernet
0/0/0
192.168.2.0/24 EBGP 255 2 D 10.10.10.9 GigabitEthernet
0/0/1
192.168.3.0/24 IBGP 255 2 RD 8.8.8.8 GigabitEthernet
0/0/2
192.168.4.0/24 IBGP 255 2 RD 8.8.8.8 GigabitEthernet
0/0/2
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
<R5>display current-configuration
[V200R003C00]
#
sysname R5
#
board add 0/1 1GEC
#
snmp-agent local-engineid 800007DB03000000000000
snmp-agent
#
clock timezone China-Standard-Time minus 08:00:00
#
portal local-server load portalpage.zip
#
drop illegal-mac alarm
#
set cpu-usage threshold 80 restore 75
#
aaa
authentication-scheme default
authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password cipher %$%$K8m.Nt84DZ}e#<0`8bmE3Uw}%$%$
local-user admin service-type http
#
firewall zone Local
priority 15
#
interface GigabitEthernet0/0/0
ip address 10.10.10.2 255.255.255.252
#
interface GigabitEthernet0/0/1
ip address 10.10.10.10 255.255.255.252
#
interface GigabitEthernet0/0/2
ip address 10.10.10.21 255.255.255.252
#
interface GigabitEthernet1/0/0
ip address 10.10.10.17 255.255.255.252
#
interface NULL0
#
interface LoopBack0
ip address 5.5.5.5 255.255.255.255
#
bgp 200
router-id 5.5.5.5
peer 6.6.6.6 as-number 200
peer 6.6.6.6 connect-interface LoopBack0
peer 7.7.7.7 as-number 200
peer 7.7.7.7 connect-interface LoopBack0
peer 8.8.8.8 as-number 200
peer 8.8.8.8 connect-interface LoopBack0
peer 10.10.10.1 as-number 100
peer 10.10.10.9 as-number 100
#
ipv4-family unicast
undo synchronization
peer 6.6.6.6 enable
peer 7.7.7.7 enable
peer 7.7.7.7 next-hop-local
peer 8.8.8.8 enable
peer 8.8.8.8 next-hop-local
peer 10.10.10.1 enable
peer 10.10.10.9 enable
#
ospf 10 router-id 5.5.5.5
area 0.0.0.0
network 5.5.5.5 0.0.0.0
network 10.10.10.17 0.0.0.0
network 10.10.10.21 0.0.0.0
#
user-interface con 0
authentication-mode password
user-interface vty 0 4
user-interface vty 16 20
#
wlan ac
#
return
<R5>AR6：
<R6>display ip interface brief
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 6
The number of interface that is DOWN in Physical is 0
The number of interface that is UP in Protocol is 6
The number of interface that is DOWN in Protocol is 0
Interface IP Address/Mask Physical Protocol
GigabitEthernet0/0/0 10.10.10.14/30 up up
GigabitEthernet0/0/1 10.10.10.6/30 up up
GigabitEthernet0/0/2 10.10.10.25/30 up up
GigabitEthernet1/0/0 10.10.10.18/30 up up
LoopBack0 6.6.6.6/32 up up(s)
NULL0 unassigned up up(s)
<R6>display ospf peer brief
OSPF Process 10 with Router ID 6.6.6.6
Peer Statistic Information
----------------------------------------------------------------------------
Area Id Interface Neighbor id State
0.0.0.0 GigabitEthernet0/0/2 7.7.7.7 Full
0.0.0.0 GigabitEthernet1/0/0 5.5.5.5 Full
----------------------------------------------------------------------------
<R6>display ospf lsdb
OSPF Process 10 with Router ID 6.6.6.6
Link State Database
Area: 0.0.0.0
Type LinkState ID AdvRouter Age Len Sequence Metric
Router 7.7.7.7 7.7.7.7 384 84 80000016 1
Router 6.6.6.6 6.6.6.6 481 60 80000011 1
Router 8.8.8.8 8.8.8.8 355 48 8000000D 1
Router 5.5.5.5 5.5.5.5 493 60 80000013 1
Network 10.10.10.17 5.5.5.5 623 32 8000000A 0
Network 10.10.10.21 5.5.5.5 493 32 8000000A 0
Network 10.10.10.25 6.6.6.6 481 32 8000000A 0
Network 10.10.10.29 7.7.7.7 384 32 8000000A 0
<R6>display bgp peer
BGP local router ID : 6.6.6.6
Local AS number : 200
Total number of peers : 5 Peers in established state : 5
Peer V AS MsgRcvd MsgSent OutQ Up/Down State Pre
fRcv
5.5.5.5 4 200 247 247 0 03:58:04 Established
2
7.7.7.7 4 200 237 247 0 03:55:53 Established
0
8.8.8.8 4 200 240 246 0 03:54:10 Established
2
10.10.10.5 4 100 249 254 0 03:58:32 Established
2
10.10.10.13 4 100 251 255 0 03:58:28 Established
2
<R6>display bgp routing-table
BGP Local router ID is 6.6.6.6
Status codes: * - valid, > - best, d - damped,
h - history, i - internal, s - suppressed, S - Stale
Origin : i - IGP, e - EGP, ? - incomplete
Total Number of Routes: 8
Network NextHop MED LocPrf PrefVal Path/Ogn
*> 192.168.1.0 10.10.10.5 2 0 100i
* 10.10.10.13 10 0 100i
i 10.10.10.1 2 100 0 100i
*> 192.168.2.0 10.10.10.13 2 0 100i
* 10.10.10.5 10 0 100i
i 10.10.10.9 2 100 0 100i
*>i 192.168.3.0 8.8.8.8 2 100 0 100i
*>i 192.168.4.0 8.8.8.8 2 100 0 100i
<R6>display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 27 Routes : 28
Destination/Mask Proto Pre Cost Flags NextHop Interface
5.5.5.5/32 OSPF 10 1 D 10.10.10.17 GigabitEthernet
1/0/0
6.6.6.6/32 Direct 0 0 D 127.0.0.1 LoopBack0
7.7.7.7/32 OSPF 10 1 D 10.10.10.26 GigabitEthernet
0/0/2
8.8.8.8/32 OSPF 10 2 D 10.10.10.26 GigabitEthernet
0/0/2
10.10.10.4/30 Direct 0 0 D 10.10.10.6 GigabitEthernet
0/0/1
10.10.10.6/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
10.10.10.7/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
10.10.10.12/30 Direct 0 0 D 10.10.10.14 GigabitEthernet
0/0/0
10.10.10.14/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
10.10.10.15/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
10.10.10.16/30 Direct 0 0 D 10.10.10.18 GigabitEthernet
1/0/0
10.10.10.18/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
1/0/0
10.10.10.19/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
1/0/0
10.10.10.20/30 OSPF 10 2 D 10.10.10.17 GigabitEthernet
1/0/0
OSPF 10 2 D 10.10.10.26 GigabitEthernet
0/0/2
10.10.10.24/30 Direct 0 0 D 10.10.10.25 GigabitEthernet
0/0/2
10.10.10.25/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
10.10.10.27/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
10.10.10.28/30 OSPF 10 2 D 10.10.10.26 GigabitEthernet
0/0/2
10.10.10.32/30 OSPF 10 2 D 10.10.10.26 GigabitEthernet
0/0/2
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
192.168.1.0/24 EBGP 255 2 D 10.10.10.5 GigabitEthernet
0/0/1
192.168.2.0/24 EBGP 255 2 D 10.10.10.13 GigabitEthernet
0/0/0
192.168.3.0/24 IBGP 255 2 RD 8.8.8.8 GigabitEthernet
0/0/2
192.168.4.0/24 IBGP 255 2 RD 8.8.8.8 GigabitEthernet
0/0/2
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
<R6>display current-configuration
[V200R003C00]
#
sysname R6
#
board add 0/1 1GEC
#
snmp-agent local-engineid 800007DB03000000000000
snmp-agent
#
clock timezone China-Standard-Time minus 08:00:00
#
portal local-server load portalpage.zip
#
drop illegal-mac alarm
#
set cpu-usage threshold 80 restore 75
#
aaa
authentication-scheme default
authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password cipher %$%$K8m.Nt84DZ}e#<0`8bmE3Uw}%$%$
local-user admin service-type http
#
firewall zone Local
priority 15
#
interface GigabitEthernet0/0/0
ip address 10.10.10.14 255.255.255.252
#
interface GigabitEthernet0/0/1
ip address 10.10.10.6 255.255.255.252
#
interface GigabitEthernet0/0/2
ip address 10.10.10.25 255.255.255.252
#
interface GigabitEthernet1/0/0
ip address 10.10.10.18 255.255.255.252
#
interface NULL0
#
interface LoopBack0
ip address 6.6.6.6 255.255.255.255
#
bgp 200
router-id 6.6.6.6
peer 5.5.5.5 as-number 200
peer 5.5.5.5 connect-interface LoopBack0
peer 7.7.7.7 as-number 200
peer 7.7.7.7 connect-interface LoopBack0
peer 8.8.8.8 as-number 200
peer 8.8.8.8 connect-interface LoopBack0
peer 10.10.10.5 as-number 100
peer 10.10.10.13 as-number 100
#
ipv4-family unicast
undo synchronization
peer 5.5.5.5 enable
peer 7.7.7.7 enable
peer 7.7.7.7 next-hop-local
peer 8.8.8.8 enable
peer 8.8.8.8 next-hop-local
peer 10.10.10.5 enable
peer 10.10.10.5 route-policy policy-1 export
peer 10.10.10.13 enable
peer 10.10.10.13 route-policy policy-1 export
#
ospf 10 router-id 6.6.6.6
area 0.0.0.0
network 6.6.6.6 0.0.0.0
network 10.10.10.18 0.0.0.0
network 10.10.10.25 0.0.0.0
#
route-policy policy-1 permit node 10
apply cost 10
#
route-policy policy-1 permit node 20
#
user-interface con 0
authentication-mode password
user-interface vty 0 4
user-interface vty 16 20
#
wlan ac
#
return
<R6> AR7：
<R7>display ip interface brief
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 6
The number of interface that is DOWN in Physical is 0
The number of interface that is UP in Protocol is 6
The number of interface that is DOWN in Protocol is 0
Interface IP Address/Mask Physical Protocol
GigabitEthernet0/0/0 10.10.10.22/30 up up
GigabitEthernet0/0/1 10.10.10.26/30 up up
GigabitEthernet0/0/2 10.10.10.29/30 up up
GigabitEthernet1/0/0 10.10.10.33/30 up up
LoopBack0 7.7.7.7/32 up up(s)
NULL0 unassigned up up(s)
<R7>display ospf peer brief
OSPF Process 10 with Router ID 7.7.7.7
Peer Statistic Information
----------------------------------------------------------------------------
Area Id Interface Neighbor id State
0.0.0.0 GigabitEthernet0/0/0 5.5.5.5 Full
0.0.0.0 GigabitEthernet0/0/1 6.6.6.6 Full
0.0.0.0 GigabitEthernet0/0/2 8.8.8.8 Full
----------------------------------------------------------------------------
<R7>display ospf lsdb
OSPF Process 10 with Router ID 7.7.7.7
Link State Database
Area: 0.0.0.0
Type LinkState ID AdvRouter Age Len Sequence Metric
Router 7.7.7.7 7.7.7.7 477 84 80000016 1
Router 6.6.6.6 6.6.6.6 576 60 80000011 1
Router 8.8.8.8 8.8.8.8 448 48 8000000D 1
Router 5.5.5.5 5.5.5.5 586 60 80000013 1
Network 10.10.10.17 5.5.5.5 716 32 8000000A 0
Network 10.10.10.21 5.5.5.5 586 32 8000000A 0
Network 10.10.10.25 6.6.6.6 576 32 8000000A 0
Network 10.10.10.29 7.7.7.7 477 32 8000000A 0
<R7>display bgp peer
BGP local router ID : 7.7.7.7
Local AS number : 200
Total number of peers : 3 Peers in established state : 3
Peer V AS MsgRcvd MsgSent OutQ Up/Down State Pre
fRcv
5.5.5.5 4 200 247 239 0 03:57:52 Established
2
6.6.6.6 4 200 247 239 0 03:57:34 Established
2
8.8.8.8 4 200 242 240 0 03:56:12 Established
2
<R7>display bgp routing-table
BGP Local router ID is 7.7.7.7
Status codes: * - valid, > - best, d - damped,
h - history, i - internal, s - suppressed, S - Stale
Origin : i - IGP, e - EGP, ? - incomplete
Total Number of Routes: 6
Network NextHop MED LocPrf PrefVal Path/Ogn
*>i 192.168.1.0 5.5.5.5 2 100 0 100i
* i 6.6.6.6 2 100 0 100i
*>i 192.168.2.0 5.5.5.5 2 100 0 100i
* i 6.6.6.6 2 100 0 100i
*>i 192.168.3.0 8.8.8.8 2 100 0 100i
*>i 192.168.4.0 8.8.8.8 2 100 0 100i
<R7>display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 25 Routes : 26
Destination/Mask Proto Pre Cost Flags NextHop Interface
5.5.5.5/32 OSPF 10 1 D 10.10.10.21 GigabitEthernet
0/0/0
6.6.6.6/32 OSPF 10 1 D 10.10.10.25 GigabitEthernet
0/0/1
7.7.7.7/32 Direct 0 0 D 127.0.0.1 LoopBack0
8.8.8.8/32 OSPF 10 1 D 10.10.10.30 GigabitEthernet
0/0/2
10.10.10.16/30 OSPF 10 2 D 10.10.10.21 GigabitEthernet
0/0/0
OSPF 10 2 D 10.10.10.25 GigabitEthernet
0/0/1
10.10.10.20/30 Direct 0 0 D 10.10.10.22 GigabitEthernet
0/0/0
10.10.10.22/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
10.10.10.23/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
10.10.10.24/30 Direct 0 0 D 10.10.10.26 GigabitEthernet
0/0/1
10.10.10.26/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
10.10.10.27/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
10.10.10.28/30 Direct 0 0 D 10.10.10.29 GigabitEthernet
0/0/2
10.10.10.29/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
10.10.10.31/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
10.10.10.32/30 Direct 0 0 D 10.10.10.33 GigabitEthernet
1/0/0
10.10.10.33/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
1/0/0
10.10.10.35/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
1/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
192.168.1.0/24 IBGP 255 2 RD 5.5.5.5 GigabitEthernet
0/0/0
192.168.2.0/24 IBGP 255 2 RD 5.5.5.5 GigabitEthernet
0/0/0
192.168.3.0/24 IBGP 255 2 RD 8.8.8.8 GigabitEthernet
0/0/2
192.168.4.0/24 IBGP 255 2 RD 8.8.8.8 GigabitEthernet
0/0/2
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
<R7>display current-configuration
[V200R003C00]
#
sysname R7
#
board add 0/1 1GEC
#
snmp-agent local-engineid 800007DB03000000000000
snmp-agent
#
clock timezone China-Standard-Time minus 08:00:00
#
portal local-server load portalpage.zip
#
drop illegal-mac alarm
#
set cpu-usage threshold 80 restore 75
#
aaa
authentication-scheme default
authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password cipher %$%$K8m.Nt84DZ}e#<0`8bmE3Uw}%$%$
local-user admin service-type http
#
firewall zone Local
priority 15
#
interface GigabitEthernet0/0/0
ip address 10.10.10.22 255.255.255.252
#
interface GigabitEthernet0/0/1
ip address 10.10.10.26 255.255.255.252
#
interface GigabitEthernet0/0/2
ip address 10.10.10.29 255.255.255.252
#
interface GigabitEthernet1/0/0
ip address 10.10.10.33 255.255.255.252
#
interface NULL0
#
interface LoopBack0
ip address 7.7.7.7 255.255.255.255
#
bgp 200
router-id 7.7.7.7
peer 5.5.5.5 as-number 200
peer 5.5.5.5 connect-interface LoopBack0
peer 6.6.6.6 as-number 200
peer 6.6.6.6 connect-interface LoopBack0
peer 8.8.8.8 as-number 200
peer 8.8.8.8 connect-interface LoopBack0
#
ipv4-family unicast
undo synchronization
peer 5.5.5.5 enable
peer 6.6.6.6 enable
peer 8.8.8.8 enable
#
ospf 10 router-id 7.7.7.7
area 0.0.0.0
network 7.7.7.7 0.0.0.0
network 10.10.10.22 0.0.0.0
network 10.10.10.26 0.0.0.0
network 10.10.10.29 0.0.0.0
network 10.10.10.33 0.0.0.0
#
user-interface con 0
authentication-mode password
user-interface vty 0 4
user-interface vty 16 20
#
wlan ac
#
return
<R7> AR8：
<R8>display ip interface brief
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 5
The number of interface that is DOWN in Physical is 1
The number of interface that is UP in Protocol is 4
The number of interface that is DOWN in Protocol is 2
Interface IP Address/Mask Physical Protocol
GigabitEthernet0/0/0 10.10.10.30/30 up up
GigabitEthernet0/0/1 10.10.10.34/30 down down
GigabitEthernet0/0/2 10.10.10.37/30 up up
GigabitEthernet1/0/0 unassigned up down
LoopBack0 8.8.8.8/32 up up(s)
NULL0 unassigned up up(s)
<R8>display ospf peer brief
OSPF Process 10 with Router ID 8.8.8.8
Peer Statistic Information
----------------------------------------------------------------------------
Area Id Interface Neighbor id State
0.0.0.0 GigabitEthernet0/0/0 7.7.7.7 Full
----------------------------------------------------------------------------
<R8>display ospf lsdb
OSPF Process 10 with Router ID 8.8.8.8
Link State Database
Area: 0.0.0.0
Type LinkState ID AdvRouter Age Len Sequence Metric
Router 7.7.7.7 7.7.7.7 572 84 80000016 1
Router 6.6.6.6 6.6.6.6 671 60 80000011 1
Router 8.8.8.8 8.8.8.8 541 48 8000000D 1
Router 5.5.5.5 5.5.5.5 682 60 80000013 1
Network 10.10.10.17 5.5.5.5 812 32 8000000A 0
Network 10.10.10.21 5.5.5.5 682 32 8000000A 0
Network 10.10.10.25 6.6.6.6 671 32 8000000A 0
Network 10.10.10.29 7.7.7.7 572 32 8000000A 0
<R8>display bgp peer
BGP local router ID : 8.8.8.8
Local AS number : 200
Total number of peers : 4 Peers in established state : 4
Peer V AS MsgRcvd MsgSent OutQ Up/Down State Pre
fRcv
5.5.5.5 4 200 246 242 0 03:56:40 Established
2
6.6.6.6 4 200 247 243 0 03:57:16 Established
2
7.7.7.7 4 200 239 243 0 03:57:37 Established
0
10.10.10.38 4 100 240 240 0 03:55:07 Established
2
<R8>display bgp routing-table
BGP Local router ID is 8.8.8.8
Status codes: * - valid, > - best, d - damped,
h - history, i - internal, s - suppressed, S - Stale
Origin : i - IGP, e - EGP, ? - incomplete
Total Number of Routes: 6
Network NextHop MED LocPrf PrefVal Path/Ogn
*>i 192.168.1.0 5.5.5.5 2 100 0 100i
* i 6.6.6.6 2 100 0 100i
*>i 192.168.2.0 5.5.5.5 2 100 0 100i
* i 6.6.6.6 2 100 0 100i
*> 192.168.3.0 10.10.10.38 2 0 100i
*> 192.168.4.0 10.10.10.38 2 0 100i
<R8>display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 22 Routes : 22
Destination/Mask Proto Pre Cost Flags NextHop Interface
5.5.5.5/32 OSPF 10 2 D 10.10.10.29 GigabitEthernet
0/0/0
6.6.6.6/32 OSPF 10 2 D 10.10.10.29 GigabitEthernet
0/0/0
7.7.7.7/32 OSPF 10 1 D 10.10.10.29 GigabitEthernet
0/0/0
8.8.8.8/32 Direct 0 0 D 127.0.0.1 LoopBack0
10.10.10.16/30 OSPF 10 3 D 10.10.10.29 GigabitEthernet
0/0/0
10.10.10.20/30 OSPF 10 2 D 10.10.10.29 GigabitEthernet
0/0/0
10.10.10.24/30 OSPF 10 2 D 10.10.10.29 GigabitEthernet
0/0/0
10.10.10.28/30 Direct 0 0 D 10.10.10.30 GigabitEthernet
0/0/0
10.10.10.30/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
10.10.10.31/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
10.10.10.32/30 OSPF 10 2 D 10.10.10.29 GigabitEthernet
0/0/0
10.10.10.36/30 Direct 0 0 D 10.10.10.37 GigabitEthernet
0/0/2
10.10.10.37/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
10.10.10.39/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/2
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
192.168.1.0/24 IBGP 255 2 RD 5.5.5.5 GigabitEthernet
0/0/0
192.168.2.0/24 IBGP 255 2 RD 5.5.5.5 GigabitEthernet
0/0/0
192.168.3.0/24 EBGP 255 2 D 10.10.10.38 GigabitEthernet
0/0/2
192.168.4.0/24 EBGP 255 2 D 10.10.10.38 GigabitEthernet
0/0/2
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
<R8>display current-configuration
[V200R003C00]
#
sysname R8
#
board add 0/1 1GEC
#
snmp-agent local-engineid 800007DB03000000000000
snmp-agent
#
clock timezone China-Standard-Time minus 08:00:00
#
portal local-server load portalpage.zip
#
drop illegal-mac alarm
#
set cpu-usage threshold 80 restore 75
#
aaa
authentication-scheme default
authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password cipher %$%$K8m.Nt84DZ}e#<0`8bmE3Uw}%$%$
local-user admin service-type http
#
firewall zone Local
priority 15
#
interface GigabitEthernet0/0/0
ip address 10.10.10.30 255.255.255.252
#
interface GigabitEthernet0/0/1
ip address 10.10.10.34 255.255.255.252
#
interface GigabitEthernet0/0/2
ip address 10.10.10.37 255.255.255.252
#
interface GigabitEthernet1/0/0
#
interface NULL0
#
interface LoopBack0
ip address 8.8.8.8 255.255.255.255
#
bgp 200
router-id 8.8.8.8
peer 5.5.5.5 as-number 200
peer 5.5.5.5 connect-interface LoopBack0
peer 6.6.6.6 as-number 200
peer 6.6.6.6 connect-interface LoopBack0
peer 7.7.7.7 as-number 200
peer 7.7.7.7 connect-interface LoopBack0
peer 10.10.10.38 as-number 100
#
ipv4-family unicast
undo synchronization
peer 5.5.5.5 enable
peer 5.5.5.5 next-hop-local
peer 6.6.6.6 enable
peer 6.6.6.6 next-hop-local
peer 7.7.7.7 enable
peer 7.7.7.7 next-hop-local
peer 10.10.10.38 enable
#
ospf 10 router-id 8.8.8.8
area 0.0.0.0
network 8.8.8.8 0.0.0.0
network 10.10.10.30 0.0.0.0
network 10.10.10.34 0.0.0.0
#
user-interface con 0
authentication-mode password
user-interface vty 0 4
user-interface vty 16 20
#
wlan ac
#
return
<R8>AR9：
<R9>display ip interface brief
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 3
The number of interface that is DOWN in Physical is 1
The number of interface that is UP in Protocol is 3
The number of interface that is DOWN in Protocol is 1
Interface IP Address/Mask Physical Protocol
GigabitEthernet0/0/0 10.10.10.38/30 up up
GigabitEthernet0/0/1 192.168.200.2/30 up up
GigabitEthernet0/0/2 unassigned down down
NULL0 unassigned up up(s)
<R9>display ospf peer brief
OSPF Process 200 with Router ID 9.9.9.9
Peer Statistic Information
----------------------------------------------------------------------------
Area Id Interface Neighbor id State
0.0.0.0 GigabitEthernet0/0/1 10.10.10.10 Full
----------------------------------------------------------------------------
<R9>display ospf lsdb
OSPF Process 200 with Router ID 9.9.9.9
Link State Database
Area: 0.0.0.0
Type LinkState ID AdvRouter Age Len Sequence Metric
Router 9.9.9.9 9.9.9.9 702 36 8000000E 1
Router 10.10.10.10 10.10.10.10 456 60 80000010 1
Network 192.168.200.2 9.9.9.9 463 32 8000000B 0
AS External Database
Type LinkState ID AdvRouter Age Len Sequence Metric
External 192.168.2.0 9.9.9.9 1356 36 80000008 1
External 192.168.1.0 9.9.9.9 1356 36 80000008 1
<R9>display bgp peer
BGP local router ID : 9.9.9.9
Local AS number : 100
Total number of peers : 1 Peers in established state : 1
Peer V AS MsgRcvd MsgSent OutQ Up/Down State Pre
fRcv
10.10.10.37 4 200 240 241 0 03:56:27 Established
2
<R9>display bgp routing-table
BGP Local router ID is 9.9.9.9
Status codes: * - valid, > - best, d - damped,
h - history, i - internal, s - suppressed, S - Stale
Origin : i - IGP, e - EGP, ? - incomplete
Total Number of Routes: 4
Network NextHop MED LocPrf PrefVal Path/Ogn
*> 192.168.1.0 10.10.10.37 0 200 100i
*> 192.168.2.0 10.10.10.37 0 200 100i
*> 192.168.3.0 0.0.0.0 2 0 i
*> 192.168.4.0 0.0.0.0 2 0 i
<R9>display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 14 Routes : 14
Destination/Mask Proto Pre Cost Flags NextHop Interface
10.10.10.36/30 Direct 0 0 D 10.10.10.38 GigabitEthernet
0/0/0
10.10.10.38/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
10.10.10.39/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
192.168.1.0/24 EBGP 255 0 D 10.10.10.37 GigabitEthernet
0/0/0
192.168.2.0/24 EBGP 255 0 D 10.10.10.37 GigabitEthernet
0/0/0
192.168.3.0/24 OSPF 10 2 D 192.168.200.1 GigabitEthernet
0/0/1
192.168.4.0/24 OSPF 10 2 D 192.168.200.1 GigabitEthernet
0/0/1
192.168.200.0/30 Direct 0 0 D 192.168.200.2 GigabitEthernet
0/0/1
192.168.200.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
192.168.200.3/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
<R9>display current-configuration
[V200R003C00]
#
sysname R9
#
snmp-agent local-engineid 800007DB03000000000000
snmp-agent
#
clock timezone China-Standard-Time minus 08:00:00
#
portal local-server load portalpage.zip
#
drop illegal-mac alarm
#
set cpu-usage threshold 80 restore 75
#
aaa
authentication-scheme default
authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password cipher %$%$K8m.Nt84DZ}e#<0`8bmE3Uw}%$%$
local-user admin service-type http
#
firewall zone Local
priority 15
#
interface GigabitEthernet0/0/0
ip address 10.10.10.38 255.255.255.252
#
interface GigabitEthernet0/0/1
ip address 192.168.200.2 255.255.255.252
#
interface GigabitEthernet0/0/2
#
interface NULL0
#
bgp 100
router-id 9.9.9.9
peer 10.10.10.37 as-number 200
#
ipv4-family unicast
undo synchronization
network 192.168.3.0
network 192.168.4.0
peer 10.10.10.37 enable
peer 10.10.10.37 allow-as-loop
#
ospf 200 router-id 9.9.9.9
import-route bgp type 1
area 0.0.0.0
network 192.168.200.2 0.0.0.0
#
user-interface con 0
authentication-mode password
user-interface vty 0 4
user-interface vty 16 20
#
wlan ac
#
return
<R9> AR10：
<R10>display ip interface brief
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 5
The number of interface that is DOWN in Physical is 1
The number of interface that is UP in Protocol is 4
The number of interface that is DOWN in Protocol is 2
Interface IP Address/Mask Physical Protocol
GigabitEthernet0/0/0 192.168.200.1/30 up up
GigabitEthernet0/0/1 unassigned up down
GigabitEthernet0/0/1.1 192.168.3.254/24 up up
GigabitEthernet0/0/1.2 192.168.4.254/24 up up
GigabitEthernet0/0/2 unassigned down down
NULL0 unassigned up up(s)
<R10>display ospf peer brief
OSPF Process 200 with Router ID 10.10.10.10
Peer Statistic Information
----------------------------------------------------------------------------
Area Id Interface Neighbor id State
0.0.0.0 GigabitEthernet0/0/0 9.9.9.9 Full
----------------------------------------------------------------------------
<R10>display ospf lsdb
OSPF Process 200 with Router ID 10.10.10.10
Link State Database
Area: 0.0.0.0
Type LinkState ID AdvRouter Age Len Sequence Metric
Router 9.9.9.9 9.9.9.9 790 36 8000000E 1
Router 10.10.10.10 10.10.10.10 542 60 80000010 1
Network 192.168.200.2 9.9.9.9 551 32 8000000B 0
AS External Database
Type LinkState ID AdvRouter Age Len Sequence Metric
External 192.168.2.0 9.9.9.9 1444 36 80000008 1
External 192.168.1.0 9.9.9.9 1444 36 80000008 1
<R10>display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: Public
Destinations : 15 Routes : 15
Destination/Mask Proto Pre Cost Flags NextHop Interface
127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0
127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
192.168.1.0/24 O_ASE 150 2 D 192.168.200.2 GigabitEthernet
0/0/0
192.168.2.0/24 O_ASE 150 2 D 192.168.200.2 GigabitEthernet
0/0/0
192.168.3.0/24 Direct 0 0 D 192.168.3.254 GigabitEthernet
0/0/1.1
192.168.3.254/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1.1
192.168.3.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1.1
192.168.4.0/24 Direct 0 0 D 192.168.4.254 GigabitEthernet
0/0/1.2
192.168.4.254/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1.2
192.168.4.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/1.2
192.168.200.0/30 Direct 0 0 D 192.168.200.1 GigabitEthernet
0/0/0
192.168.200.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
192.168.200.3/32 Direct 0 0 D 127.0.0.1 GigabitEthernet
0/0/0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0
<R10>display current-configuration
[V200R003C00]
#
sysname R10
#
snmp-agent local-engineid 800007DB03000000000000
snmp-agent
#
clock timezone China-Standard-Time minus 08:00:00
#
portal local-server load portalpage.zip
#
drop illegal-mac alarm
#
set cpu-usage threshold 80 restore 75
#
aaa
authentication-scheme default
authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password cipher %$%$K8m.Nt84DZ}e#<0`8bmE3Uw}%$%$
local-user admin service-type http
#
firewall zone Local
priority 15
#
interface GigabitEthernet0/0/0
ip address 192.168.200.1 255.255.255.252
#
interface GigabitEthernet0/0/1
#
interface GigabitEthernet0/0/1.1
dot1q termination vid 10
ip address 192.168.3.254 255.255.255.0
arp broadcast enable
#
interface GigabitEthernet0/0/1.2
dot1q termination vid 20
ip address 192.168.4.254 255.255.255.0
arp broadcast enable
#
interface GigabitEthernet0/0/2
#
interface NULL0
#
ospf 200 router-id 10.10.10.10
area 0.0.0.0
network 192.168.3.254 0.0.0.0
network 192.168.4.254 0.0.0.0
network 192.168.200.1 0.0.0.0
#
user-interface con 0
authentication-mode password
user-interface vty 0 4
user-interface vty 16 20
#
wlan ac
#
return
<R10> LSW1：
<SW1>display interface brief
PHY: Physical
*down: administratively down
(l): loopback
(s): spoofing
(b): BFD down
(e): ETHOAM down
(dl): DLDP down
(d): Dampening Suppressed
InUti/OutUti: input utility/output utility
Interface PHY Protocol InUti OutUti inErrors outErrors
GigabitEthernet0/0/1 up up 0% 0% 0 0
GigabitEthernet0/0/2 up up 0% 0% 0 0
GigabitEthernet0/0/3 up up 0% 0% 0 0
GigabitEthernet0/0/4 down down 0% 0% 0 0
GigabitEthernet0/0/5 down down 0% 0% 0 0
GigabitEthernet0/0/6 down down 0% 0% 0 0
GigabitEthernet0/0/7 down down 0% 0% 0 0
GigabitEthernet0/0/8 down down 0% 0% 0 0
GigabitEthernet0/0/9 down down 0% 0% 0 0
GigabitEthernet0/0/10 down down 0% 0% 0 0
GigabitEthernet0/0/11 down down 0% 0% 0 0
GigabitEthernet0/0/12 down down 0% 0% 0 0
GigabitEthernet0/0/13 down down 0% 0% 0 0
GigabitEthernet0/0/14 down down 0% 0% 0 0
GigabitEthernet0/0/15 down down 0% 0% 0 0
GigabitEthernet0/0/16 down down 0% 0% 0 0
GigabitEthernet0/0/17 down down 0% 0% 0 0
GigabitEthernet0/0/18 down down 0% 0% 0 0
GigabitEthernet0/0/19 down down 0% 0% 0 0
GigabitEthernet0/0/20 down down 0% 0% 0 0
GigabitEthernet0/0/21 down down 0% 0% 0 0
GigabitEthernet0/0/22 down down 0% 0% 0 0
GigabitEthernet0/0/23 down down 0% 0% 0 0
GigabitEthernet0/0/24 down down 0% 0% 0 0
MEth0/0/1 down down 0% 0% 0 0
NULL0 up up(s) 0% 0% 0 0
Vlanif1 up down -- -- 0 0
<SW1>LSW2：
<SW2>display interface brief
PHY: Physical
*down: administratively down
(l): loopback
(s): spoofing
(b): BFD down
(e): ETHOAM down
(dl): DLDP down
(d): Dampening Suppressed
InUti/OutUti: input utility/output utility
Interface PHY Protocol InUti OutUti inErrors outErrors
GigabitEthernet0/0/1 up up 0% 0% 0 0
GigabitEthernet0/0/2 up up 0% 0% 0 0
GigabitEthernet0/0/3 up up 0% 0% 0 0
GigabitEthernet0/0/4 down down 0% 0% 0 0
GigabitEthernet0/0/5 down down 0% 0% 0 0
GigabitEthernet0/0/6 down down 0% 0% 0 0
GigabitEthernet0/0/7 down down 0% 0% 0 0
GigabitEthernet0/0/8 down down 0% 0% 0 0
GigabitEthernet0/0/9 down down 0% 0% 0 0
GigabitEthernet0/0/10 down down 0% 0% 0 0
GigabitEthernet0/0/11 down down 0% 0% 0 0
GigabitEthernet0/0/12 down down 0% 0% 0 0
GigabitEthernet0/0/13 down down 0% 0% 0 0
GigabitEthernet0/0/14 down down 0% 0% 0 0
GigabitEthernet0/0/15 down down 0% 0% 0 0
GigabitEthernet0/0/16 down down 0% 0% 0 0
GigabitEthernet0/0/17 down down 0% 0% 0 0
GigabitEthernet0/0/18 down down 0% 0% 0 0
GigabitEthernet0/0/19 down down 0% 0% 0 0
GigabitEthernet0/0/20 down down 0% 0% 0 0
GigabitEthernet0/0/21 down down 0% 0% 0 0
GigabitEthernet0/0/22 down down 0% 0% 0 0
GigabitEthernet0/0/23 down down 0% 0% 0 0
GigabitEthernet0/0/24 down down 0% 0% 0 0
MEth0/0/1 down down 0% 0% 0 0
NULL0 up up(s) 0% 0% 0 0
Vlanif1 up down -- -- 0 0
<SW2>LSW4：
<SW4>display interface brief
PHY: Physical
*down: administratively down
(l): loopback
(s): spoofing
(b): BFD down
(e): ETHOAM down
(dl): DLDP down
(d): Dampening Suppressed
InUti/OutUti: input utility/output utility
Interface PHY Protocol InUti OutUti inErrors outErrors
GigabitEthernet0/0/1 up up 0% 0% 0 0
GigabitEthernet0/0/2 up up 0% 0% 0 0
GigabitEthernet0/0/3 up up 0% 0% 0 0
GigabitEthernet0/0/4 down down 0% 0% 0 0
GigabitEthernet0/0/5 down down 0% 0% 0 0
GigabitEthernet0/0/6 down down 0% 0% 0 0
GigabitEthernet0/0/7 down down 0% 0% 0 0
GigabitEthernet0/0/8 down down 0% 0% 0 0
GigabitEthernet0/0/9 down down 0% 0% 0 0
GigabitEthernet0/0/10 down down 0% 0% 0 0
GigabitEthernet0/0/11 down down 0% 0% 0 0
GigabitEthernet0/0/12 down down 0% 0% 0 0
GigabitEthernet0/0/13 down down 0% 0% 0 0
GigabitEthernet0/0/14 down down 0% 0% 0 0
GigabitEthernet0/0/15 down down 0% 0% 0 0
GigabitEthernet0/0/16 down down 0% 0% 0 0
GigabitEthernet0/0/17 down down 0% 0% 0 0
GigabitEthernet0/0/18 down down 0% 0% 0 0
GigabitEthernet0/0/19 down down 0% 0% 0 0
GigabitEthernet0/0/20 down down 0% 0% 0 0
GigabitEthernet0/0/21 down down 0% 0% 0 0
GigabitEthernet0/0/22 down down 0% 0% 0 0
GigabitEthernet0/0/23 down down 0% 0% 0 0
GigabitEthernet0/0/24 down down 0% 0% 0 0
MEth0/0/1 down down 0% 0% 0 0
NULL0 up up(s) 0% 0% 0 0
Vlanif1 up down -- -- 0 0
<SW4>display vlan
The total number of vlans is : 3
--------------------------------------------------------------------------------
U: Up; D: Down; TG: Tagged; UT: Untagged;
MP: Vlan-mapping; ST: Vlan-stacking;
#: ProtocolTransparent-vlan; *: Management-vlan;
--------------------------------------------------------------------------------
VID Type Ports
--------------------------------------------------------------------------------
1 common UT:GE0/0/1(U) GE0/0/4(D) GE0/0/5(D) GE0/0/6(D)
GE0/0/7(D) GE0/0/8(D) GE0/0/9(D) GE0/0/10(D)
GE0/0/11(D) GE0/0/12(D) GE0/0/13(D) GE0/0/14(D)
GE0/0/15(D) GE0/0/16(D) GE0/0/17(D) GE0/0/18(D)
GE0/0/19(D) GE0/0/20(D) GE0/0/21(D) GE0/0/22(D)
GE0/0/23(D) GE0/0/24(D)
10 common UT:GE0/0/3(U)
TG:GE0/0/1(U)
20 common UT:GE0/0/2(U)
TG:GE0/0/1(U)
VID Status Property MAC-LRN Statistics Description
--------------------------------------------------------------------------------
1 enable default enable disable VLAN 0001
10 enable default enable disable VLAN 0010
20 enable default enable disable VLAN 0020
<SW4>display current-configuration
#
sysname SW4
#
vlan batch 10 20
#
cluster enable
ntdp enable
ndp enable
#
drop illegal-mac alarm
#
diffserv domain default
#
drop-profile default
#
aaa
authentication-scheme default
authorization-scheme default
accounting-scheme default
domain default
domain default_admin
local-user admin password simple admin
local-user admin service-type http
#
interface Vlanif1
#
interface MEth0/0/1
#
interface GigabitEthernet0/0/1
port link-type trunk
port trunk allow-pass vlan 10 20
#
interface GigabitEthernet0/0/2
port link-type access
port default vlan 20
#
interface GigabitEthernet0/0/3
port link-type access
port default vlan 10
#
interface GigabitEthernet0/0/4
#
interface GigabitEthernet0/0/5
#
interface GigabitEthernet0/0/6
#
interface GigabitEthernet0/0/7
#
interface GigabitEthernet0/0/8
#
interface GigabitEthernet0/0/9
#
interface GigabitEthernet0/0/10
#
interface GigabitEthernet0/0/11
#
interface GigabitEthernet0/0/12
#
interface GigabitEthernet0/0/13
#
interface GigabitEthernet0/0/14
#
interface GigabitEthernet0/0/15
#
interface GigabitEthernet0/0/16
#
interface GigabitEthernet0/0/17
#
interface GigabitEthernet0/0/18
#
interface GigabitEthernet0/0/19
#
interface GigabitEthernet0/0/20
#
interface GigabitEthernet0/0/21
#
interface GigabitEthernet0/0/22
#
interface GigabitEthernet0/0/23
#
interface GigabitEthernet0/0/24
#
interface NULL0
#
user-interface con 0
user-interface vty 0 4
#
return
<SW4> 
91
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
