HCIP--RIP 综合实验

1.基于10.1.1.0/24对地址进行划分

借3位 划分网段

划分出8个网段 000 100 010 001 110 011 101 111

[AR1]int g 0/0/0

[AR1-GigabitEthernet0/0/0]ip ad 10.1.1.1 27

[AR1-GigabitEthernet0/0/0]int g 0/0/1

[AR1-GigabitEthernet0/0/1]ip ad 10.1.129 27

[AR2]int g 0/0/0

[AR2-GigabitEthernet0/0/0]ip ad 10.1.1.2 27

[AR2-GigabitEthernet0/0/0]int g 0/0/1

[AR2-GigabitEthernet0/0/1]ip ad 10.1.1.65 27

[AR3]int g 0/0/0

[AR3-GigabitEthernet0/0/0]ip ad 10.1.1.66 27

[AR3-GigabitEthernet0/0/0]int g 0/0/1

[AR3-GigabitEthernet0/0/1]ip ad 10.1.1.33 27

[AR4]int g 0/0/1

[AR4-GigabitEthernet0/0/1]ip ad 10.1.1.130 27

[AR4-GigabitEthernet0/0/1]int g 0/0/0

[AR4-GigabitEthernet0/0/0]ip ad 10.1.1.34 27

[AR4-GigabitEthernet0/0/0]int g 4/0/0

[AR4-GigabitEthernet4/0/0]ip ad 10.1.1.193 27

[AR4-GigabitEthernet4/0/0]int g 0/0/2

[AR4-GigabitEthernet0/0/2]ip ad 10.1.1.97 27

[AR5]int g 0/0/0

[AR5-GigabitEthernet0/0/0]ip ad 10.1.1.194 27

[AR6]int g 0/0/0

[AR6-GigabitEthernet0/0/0]ip ad 10.1.1.98 27

[AR6-GigabitEthernet0/0/0]int g 0/0/1

[AR6-GigabitEthernet0/0/1]ip ad 10.1.1.161 27

[AR7]int g 0/0/0

[AR7-GigabitEthernet0/0/0]ip ad 10.1.1.162 27

对路由器添加环回地址

[AR1]int lo 0

[AR1-LoopBack0]ip ad 172.16.1.1 24

[AR1-LoopBack0]int lo 2

[AR1-LoopBack2]ip ad 172.16.2.1 24

[AR1-LoopBack2]int lo 3

[AR1-LoopBack3]ip ad 172.16.3.1 24

[AR2]int lo 0

[AR2-LoopBack0]ip ad 2.2.2.2 24

[AR3]int lo 0

[AR3-LoopBack0]ip ad 3.3.3.3 24

[AR4]int lo 0

[AR4-LoopBack0]ip ad 4.4.4.4 24

[AR5]int lo 0

[AR5-LoopBack0]ip ad 5.5.5.5 24

[AR7]int lo 0

[AR7-LoopBack0]ip ad 7.7.7.7 24

进行rip配置

[AR1]rip

[AR1-rip-1]version 2

[AR1-rip-1]undo summary

[AR1-rip-1]network 172.16.0.0

[AR1-rip-1]network 10.0.0.0

[AR2]rip

[AR2-rip-1]version 2

[AR2-rip-1]undo summary

[AR2-rip-1]network 10.0.0.0

[AR2-rip-1]network 2.0.0.0

[AR3]rip

[AR3-rip-1]undo summary

[AR3-rip-1]version 2

[AR3-rip-1]network 10.0.0.0

[AR3-rip-1]network 3.0.0.0

[AR4]rip

[AR4-rip-1]version 2

[AR4-rip-1]undo summary

[AR4-rip-1]network 10.0.0.0

[AR4-rip-1]network 4.0.0.0

[AR5]rip

[AR5-rip-1]version 2

[AR5-rip-1]undo summary

[AR5-rip-1]network 10.0.0.0

因为rip1和rip2的数据不能互通 所以在rip1和Rip2的边界路由器的接口上配置允许两个版本的通过

在rip v1 和rip v2 两版本边界上的路由器接口的其中之一上加入另一个版本号允许该版本流量通过

[AR6]int g0/0/0

[AR6-GigabitEthernet0/0/0]rip version 2

3.R3使用R2访问R1环回

可以使用telnet来完成 R3登陆到R2上再访问R1

[AR2]aaa

[AR2-aaa]local-user user password cipher huawei

Info: Add a new user.

[AR2-aaa]local-user user service-type telnet

[AR2-aaa]local-user user privilege level 15

[AR2]telnet server enable

[AR2]user-interface vty 0 4

[AR2-ui-vty0-4]au

[AR2-ui-vty0-4]authentication-mode aaa

一定要在用户模式下Telnet 否则不会成功

5.R5为运营商

[AR5-rip-1]default-route originate

6.R1telnetR2实际telnet到R7

按照Nat server protocol tcp global current-interface 23 inside R7ip进行配置

7.R6、R7不能学习到R1的环回路由

[AR6]acl 2000

[AR6-acl-basic-2000]rule 10 deny source 172.16.0.0 0.0.255.255

[AR6-GigabitEthernet0/0/0]traffic-filter inbound acl 2000

实验完成。