OSPF综合实验--接口实验

要求1：

首先进行基础的IP配置
[r1]interface g0/0/0
[r1-GigabitEthernet0/0/0]ip address 61.0.0.2 24
Apr  5 2024 18:19:06-08:00 r1 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP on the interfaceGigabitEthernet0/0/0 has entered the UP state. 
[r1]interface g0/0/1
[r1-GigabitEthernet0/0/1]ip address 16.0.0.2 24
Apr  5 2024 18:19:18-08:00 r1 %%01IFNET/4/LINK_STATE(l)[1]:The line protocol IP on the interfaceGigabitEthernet0/0/1 has entered the UP state. 
[r1]interface l0
[r1-LoopBack0]ip address 1.1.1.1 24
 

 

 

 每个路由器写一条指向ISP的缺省路由，保证公网能通

[r1]ip route-static 0.0.0.0 0 16.0.0.1
[r1]ip route-static 0.0.0.0 0 61.0.0.1
 

 

测试公网保证能正常通讯

要求2：

R1/R4/R5为MGRE环境
R1为中心站点

R4,R5上分别做如下配置

[r4]interface t0/0/0
[r4-Tunnel0/0/0]ip address 192.168.1.2 24
[r4-Tunnel0/0/0]tunnel-protocol gre p2mp 
[r4-Tunnel0/0/0]source g0/0/0
Apr 10 2024 11:20:06-08:00 r4 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP 
on the interface Tunnel0/0/0 has entered the UP state.     
[r4-Tunnel0/0/0]nhrp entry 192.168.1.1 16.0.0.2 register 
 

[r5]interface t0/0/0
[r5-Tunnel0/0/0]ip address 192.168.1.3 24    
[r5-Tunnel0/0/0]tunnel-protocol gre p2mp 
[r5-Tunnel0/0/0]source g0/0/0
Apr 10 2024 11:21:00-08:00 r5 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP 
on the interface Tunnel0/0/0 has entered the UP state.     

 

在R1上查看NHRP表象

 

同时在三台路由器上修改接口网络类型为broadcast，即可实现全连

R1,R2,R3为星型拓扑，创建新的隧道并做如下配置

[r2]interface t0/0/1
[r2-Tunnel0/0/1]ip address 192.168.2.2 24
[r2-Tunnel0/0/1]tunnel-protocol gre p2mp
[r2-Tunnel0/0/1]source g0/0/0
Apr 10 2024 11:39:56-08:00 r2 %%01IFNET/4/LINK_STATE(l)[2]:The line protocol IP 
on the interface Tunnel0/0/1 has entered the UP state. 
[r2-Tunnel0/0/1]nh entry 192.168.2.1 61.0.0.2 register 
 

 查看R1上的NHRP表象，得到4个表象

要求3：

将R1-R5划分到一个OSPF区域，并宣告私网网段

测试，得到结果，全网可达