ospf下的mgre实验

首先给每个路由器配置接口IP及其环回地址

[R1]int l0
[R1-LoopBack0]ip add 192.168.1.1 24
[R1-LoopBack0]int g0/0/0
[R1-GigabitEthernet0/0/0]ip add 12.0.0.1 24
[R1-GigabitEthernet0/0/0]int g0/0/1
[R1-GigabitEthernet0/0/1]ip add 21.0.0.1 24

[ISP]int g0/0/0
[ISP-GigabitEthernet0/0/0]ip add 12.0.0.2 24
[ISP-GigabitEthernet0/0/0]int g0/0/1
[ISP-GigabitEthernet0/0/1]ip add 21.0.0.2 24
[ISP-GigabitEthernet0/0/1]int g0/0/2
[ISP-GigabitEthernet0/0/2]ip add 23.0.0.2 24
[ISP-GigabitEthernet0/0/2]int g4/0/0
[ISP-GigabitEthernet4/0/0]ip add 24.0.0.2 24
[ISP-GigabitEthernet4/0/0]int g4/0/1
[ISP-GigabitEthernet4/0/1]ip add 25.0.0.2 24
[ISP-GigabitEthernet4/0/1]int g4/0/2
[ISP-GigabitEthernet4/0/2]ip add 26.0.0.2 24

[R3]int l0
[R3-LoopBack0]ip add 192.168.3.1 24
[R3-LoopBack0]int g0/0/0
[R3-GigabitEthernet0/0/0]ip add 23.0.0.1 24

[R4]int l0
[R4-LoopBack0]ip add 192.168.4.1 24
[R4-LoopBack0]int g0/0/0
[R4-GigabitEthernet0/0/0]ip add 24.0.0.1 24

[R5]int l0
[R5-LoopBack0]ip add 192.168.5.1 24
[R5-LoopBack0]int g0/0/0
[R5-GigabitEthernet0/0/0]ip add 25.0.0.1 24

[R6]int l0
[R6-LoopBack0]ip add 192.168.6.1 24
[R6-LoopBack0]int g0/0/0
[R6-GigabitEthernet0/0/0]ip add 26.0.0.1 24

接着配置除ISP外所有路由器的缺省路由

[R1]ip route-static 0.0.0.0 0 12.0.0.2
[R1]ip route-static 0.0.0.0 0 21.0.0.2

[R3]ip route-static 0.0.0.0 0 23.0.0.2

[R4]ip route-static 0.0.0.0 0 24.0.0.2

[R5]ip route-static 0.0.0.0 0 25.0.0.2

[R6]ip route-static 0.0.0.0 0 26.0.0.2

配置完成后验证是否可以ping通每个接口即可

然后用R1，R3，R4构建全连的mgre环境

第四：R1-R5-R6建立hub-spoke的MGRE环境，以R1为中心

第五：R1，R3-R6均存在环回网段模拟用户私网，利用OSPF使全网可达

最后修改接口ospf网络类型

[R1]int t0/0/0

[R1-Tunnel0/0/0]ospf network-type broadcast 
[R1-Tunnel0/0/0]int t0/0/1
[R1-Tunnel0/0/1]ospf network-type p2mp

[R3]int t0/0/0
[R3-Tunnel0/0/0]ospf network-type broadcast 

[R4]int t0/0/0
[R4-Tunnel0/0/0]ospf network-type broadcast 

[R5]int t0/0/0
[R5-Tunnel0/0/0]ospf network-type p2mp

[R6]int t0/0/0
[R6-Tunnel0/0/0]ospf network-type p2mp