为了测试前面的无线模块的程序，写了一个usart操纵Windows超级终端的程序小程序。
废话少说，上代码：
1.硬件配置的头文件：
******************** (C) COPYRIGHT 2011 SDUEM ********************
* File Name : hw_config.h
* Author : wzb@sduem
* Version : V2.2.0
* Date : 05/13/2011
* Description : Hardware Configuration & Setup
*******************************************************************************/
/* Define to prevent recursive inclusion -------------------------------------*/
#ifndef __HW_CONFIG_H
#define __HW_CONFIG_H
/* Includes ------------------------------------------------------------------*/
#include "stm32f10x_lib.h"
/* Exported types ------------------------------------------------------------*/
/* Exported constants --------------------------------------------------------*/
/* Exported variables --------------------------------------------------------*/
extern u32 TimingDelay; // delay used!
/* Exported macro ------------------------------------------------------------*/
/* Exported define -----------------------------------------------------------*/
#if 0
//------------define the usart using-----------
#define USART_USING USART1
#define RCC_APB2Periph_USART_USING RCC_APB2Periph_USART1
#define USART_USING_IRQChannel USART1_IRQChannel
//--------------define USART pins-------------------
#define USART_RX_PIN GPIO_Pin_10
#define USART_TX_PIN GPIO_Pin_9
//------------define the SPI using-----------
#define SPI_USING SPI1
#define RCC_APB2Periph_SPI_USING RCC_APB2Periph_SPI1
#define SPI_USING_IRQChannel SPI1_IRQChannel
//--------------define SPI pins-------------------
#define SPI_SCK_PIN GPIO_Pin_5
#define SPI_MISO_PIN GPIO_Pin_6
#define SPI_MOSI_PIN GPIO_Pin_7
//-------------------define the GPIO for USART_USING------------------
#define GPIO_FOR_USART GPIOA
//-------------------define the GPIO for SPI_USING------------------
#define GPIO_FOR_SPI GPIOA
#endif
/* Exported functions ------------------------------------------------------- */
void System_Init(void);
void RCC_Configuration(void); /*****与时钟相关的寄存器配制*****/
void USART_Configuration(void);
void SPI_Configuration(void);
//usart 送往超级终端上的字符显示
void usart_putc(u8 ch) ;
void usart_puts(u8 str[]) ;
void usart_println(void);
void usart_cls();
void usart_printArray( u8 * array, u32 arraySize) ;
void USART_EXTI_DoIt(); // Usart外部中断
void Decrement_TimingDelay(void);
void delay_us(u32 nCount);
/* External variables --------------------------------------------------------*/
#endif /*__HW_CONFIG_H*/
/******************* (C) COPYRIGHT 2011 SDUEM *****END OF FILE****/
2. usart功能函数的代码实现：
/******************** (C) COPYRIGHT 2011 SDUEM ********************
* File Name : hw_config.c
* Author : wzb@SDUEM
* Version : V2.2.0
* Date : 05/13/2011
* Description : Hardware Configuration & Setup
********************************************************************************
*
*******************************************************************************/
/* Includes ------------------------------------------------------------------*/
#include "hw_config.h"
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Extern variables ----------------------------------------------------------*/
/* Exported variables ----------------------------------------------------------*/
u32 TimingDelay;
/* Private function prototypes -----------------------------------------------*/
static void SysTick_Configuration(void);
static void USART1_GPIO_Configuration();
static void USART1_NVIC_Configuration();
static void USART1_Configuration();
static void SPI1_GPIO_Configuration();
static void SPI1_NVIC_Configuration();
static void SPI1_Configuration();
/* ----------------------Exported functions ----------------------------------*/
/* ---------------RCC Configuration fuction -----------------------------------*/
/*******************************************************************************
* Function Name : RCC_Configuration
* Description : Configures the system clocks
* Input : None.
* Return : None.
*******************************************************************************/
//RCC时钟配置 for the whole system
void RCC_Configuration(void) {
//定义错误状态变量
ErrorStatus HSEStartUpStatus;
//将RCC寄存器重新设置为默认值
RCC_DeInit();
//打开外部高速时钟晶振
RCC_HSEConfig(RCC_HSE_ON);
//等待外部高速时钟晶振工作
HSEStartUpStatus = RCC_WaitForHSEStartUp();
if(HSEStartUpStatus == SUCCESS) {
//设置AHB时钟(HCLK)为系统时钟
RCC_HCLKConfig(RCC_SYSCLK_Div1);
//设置高速AHB时钟(APB2)为HCLK时钟
RCC_PCLK2Config(RCC_HCLK_Div1);
//设置低速AHB时钟(APB1)为HCLK的2分频
RCC_PCLK1Config(RCC_HCLK_Div2);
//设置FLASH代码延时
FLASH_SetLatency(FLASH_Latency_2);
//使能预取指缓存
FLASH_PrefetchBufferCmd(FLASH_PrefetchBuffer_Enable);
//设置PLL时钟，为HSE的9倍频 8MHz * 9 = 72MHz
RCC_PLLConfig(RCC_PLLSource_HSE_Div1, RCC_PLLMul_9);
//使能PLL
RCC_PLLCmd(ENABLE);
//等待PLL准备就绪
while(RCC_GetFlagStatus(RCC_FLAG_PLLRDY) == RESET);
//设置PLL为系统时钟源
RCC_SYSCLKConfig(RCC_SYSCLKSource_PLLCLK);
//判断PLL是否是系统时钟
while(RCC_GetSYSCLKSource() != 0x08);
}
//打开GPIOA AFIO USART1 SPI1 时钟，复用功能，串口1的时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOB | RCC_APB2Periph_AFIO | RCC_APB2Periph_USART1 | RCC_APB2Periph_SPI1, ENABLE);
}
/*******************************************************************************
* Function Name : RCC_Configuration_1
* Description : Configures the system clocks
* Input : None.
* Return : None.
*******************************************************************************/
void RCC_Configuration_1(void)
{
ErrorStatus HSEStartUpStatus;
/* RCC system reset(for debug purpose) */
RCC_DeInit(); //将RCC寄存器设备缺省值
/* Enable HSE */
RCC_HSEConfig(RCC_HSE_ON); //外部高速振荡器HSE 开启
/* Wait till HSE is ready */
HSEStartUpStatus = RCC_WaitForHSEStartUp(); //等待HSE启动
if (HSEStartUpStatus == SUCCESS) //如果HSE晶振稳定且就绪
{
/* Enable Prefetch Buffer */
FLASH_PrefetchBufferCmd(FLASH_PrefetchBuffer_Enable); //预取指缓存使能
/* Flash 2 wait state */
FLASH_SetLatency(FLASH_Latency_2); //设置FLASH存储器延时时钟周期数为2延时周期
/* HCLK = SYSCLK */
RCC_HCLKConfig(RCC_SYSCLK_Div1); //设置AHB时钟＝系统时钟
/* PCLK2 = HCLK */
RCC_PCLK2Config(RCC_HCLK_Div1); //设置APB2时钟 ＝ HCLK
/* PCLK1 = HCLK/2 */
RCC_PCLK1Config(RCC_HCLK_Div2); //设置APB1时钟 ＝ HCLK/2
/* ADCCLK = PCLK2/6 */
RCC_ADCCLKConfig(RCC_PCLK2_Div6); //设置ADC时钟＝PCLK/6
//PLL设置
//PLL输入时钟＝HSE时钟频率 输出 9倍频（HSE×9）
RCC_PLLConfig(RCC_PLLSource_HSE_Div1, RCC_PLLMul_9); //72M
/* Enable PLL */
RCC_PLLCmd(ENABLE);
/* Wait till PLL is ready */
while (RCC_GetFlagStatus(RCC_FLAG_PLLRDY) == RESET); //等待PLL就绪
/* Select PLL as system clock source */
RCC_SYSCLKConfig(RCC_SYSCLKSource_PLLCLK); //选择PLL作为系统时钟
/* Wait till PLL is used as system clock source */
//等待设置系统时钟为PLL成功
//返回值为 00：HSI 04：HSE 08：PLL
while (RCC_GetSYSCLKSource() != 0x08);
}
RCC_APB2PeriphClockCmd( RCC_APB2Periph_GPIOA | RCC_APB2Periph_GPIOB |RCC_APB2Periph_AFIO | RCC_APB2Periph_SPI1 | RCC_APB2Periph_USART1 , ENABLE);
SysTick_Configuration();
}
/*******************************************************************************
* Function Name : SysTick_Configuration
* Description : Configure a SysTick Base time to 10 ms.
* Input : None
* Output : None
* Return : None
*******************************************************************************/
static void SysTick_Configuration(void)
{
/* Configure HCLK clock as SysTick clock source */
SysTick_CLKSourceConfig(SysTick_CLKSource_HCLK); //设置SysTick时钟为AHB时钟
/* SysTick interrupt each 72Hz with HCLK equal to 72MHz */
SysTick_SetReload(72); //设置重装值
/* Enable the SysTick Interrupt */
SysTick_ITConfig(ENABLE);
}
/*******************************************************************************
* Function Name : delay_us
* Description : Inserts a delay time.
* Input : nCount: specifies the delay time length (time base 1 us).
* Output : None
* Return : None
*******************************************************************************/
void delay_us(u32 nCount)
{
TimingDelay = nCount;
/* Enable the SysTick Counter */
SysTick_CounterCmd(SysTick_Counter_Enable);
while(TimingDelay != 0);
/* Disable the SysTick Counter */
SysTick_CounterCmd(SysTick_Counter_Disable);
/* Clear the SysTick Counter */
SysTick_CounterCmd(SysTick_Counter_Clear);
}
/*******************************************************************************
* Function Name : Decrement_TimingDelay
* Description : Decrements the TimingDelay variable.
* Input : None
* Output : TimingDelay
* Return : None
*******************************************************************************/
void Decrement_TimingDelay(void)
{
if (TimingDelay != 0x00)
{
TimingDelay--;
}
}
/* --------------- End of RCC Configuration fuction --------------------------*/
/* ---------------USART Configuration fuction --------------------------------*/
/*******************************************************************************
* Function Name : USART_Configuration
* Description : Configures the system clocks
* Input : None.
* Return : None.
*******************************************************************************/
void USART_Configuration(void) {
USART1_GPIO_Configuration();
USART1_NVIC_Configuration();
USART1_Configuration();
}
/* ---------------SPI Configuration fuction ----------------------------------*/
/*******************************************************************************
* Function Name : SPI_Configuration
* Description : Configures the system clocks
* Input : None.
* Return : None.
*******************************************************************************/
void SPI_Configuration(void) {
SPI1_GPIO_Configuration();
SPI1_NVIC_Configuration();
SPI1_Configuration();
}
/* ---------------System initial Configuration fuction ------------------------------------------*/
/*******************************************************************************
* Function Name : System_Init
* Description : Configures the system ;
* Input : None.
* Return : None.
*******************************************************************************/
void System_Init(void)
{
/* RCC configuration */
RCC_Configuration(); /*****与时钟相关的寄存器配制*****/
USART_Configuration();
SPI_Configuration();
}
/* -------------------End of Exported functions ----------------------------------*/
/* --------------private Configuration fuction for USART ------------------------------------------*/
/*******************************************************************************
* Function Name : USART1_GPIO_Configuration
* Description : Configures the USART1 GPIO Port and Pin
* Input : None.
* Return : None.
*******************************************************************************/
//GPIO口配置 for USART1
static void USART1_GPIO_Configuration(void){
GPIO_InitTypeDef GPIO_InitStructure;
//打开GPIO时钟，复用功能，串口1的时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_AFIO , ENABLE);
//PA9作为USART1的TX端，打开复用，负责发送数据
GPIO_StructInit(&GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
GPIO_Init(GPIOA, &GPIO_InitStructure);
//PA10作为USART1的RX端，负责接收数据
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_Init(GPIOA, &GPIO_InitStructure);
}
/*******************************************************************************
* Function Name : USART1_NVIC_Configuration
* Description : Configures the USART1 NVIC
* Input : None.
* Return : None.
*******************************************************************************/
//配置中断 for USART1
static void USART1_NVIC_Configuration() {
// NVIC init
#ifdef VEC_TAB_RAM
/* Set the Vector Table base location at 0x20000000 */
NVIC_SetVectorTable(NVIC_VectTab_RAM, 0x0);
#else /* VECT_TAB_FLASH */
/* Set the Vector Table base location at 0x08000000 */
NVIC_SetVectorTable(NVIC_VectTab_FLASH, 0x0);
#endif
NVIC_InitTypeDef NVIC_InitStructure;
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_2); //选择中断分组2
NVIC_InitStructure.NVIC_IRQChannel = USART1_IRQChannel; //选择串口1中断
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 0; //抢占式中断优先级设置为0
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0; //响应式中断优先级设置为0
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE; //使能中断
NVIC_Init(&NVIC_InitStructure);
}
/*******************************************************************************
* Function Name : USART1_Configuration
* Description : Configures the USART1 Configuration and enable set
* Input : None.
* Return : None.
*******************************************************************************/
//串口初始化 for USART1
static void USART1_Configuration() {
USART_InitTypeDef USART_InitStructure;
//打开USART1时钟，串口1的时钟
RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1, ENABLE);
//将结构体设置为缺省状态
USART_StructInit(&USART_InitStructure);
//波特率设置为115200
USART_InitStructure.USART_BaudRate = 115200;
//一帧数据的宽度设置为8bits
USART_InitStructure.USART_WordLength = USART_WordLength_8b;
//在帧结尾传输1个停止位
USART_InitStructure.USART_StopBits = USART_StopBits_1;
//奇偶失能模式，无奇偶校验
USART_InitStructure.USART_Parity = USART_Parity_No;
//发送/接收使能
USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
//硬件流控制失能
USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
//设置串口1
USART_Init(USART1, &USART_InitStructure);
//打开串口1的中断响应函数
USART_ITConfig(USART1, USART_IT_RXNE, ENABLE);
//打开串口1
USART_Cmd(USART1, ENABLE);
//关闭串口1的中断响应函数
//USART_ITConfig(USART1, USART_IT_RXNE, DISABLE);
}
/* -------------- End of private Configuration fuction for USART -------------*/
/* --------------private Configuration fuction for SPI------------------------*/
/*******************************************************************************
* Function Name :SPI1_GPIO_Configuration
* Description : Configures the SPI1 Configuration and enable set
* Input : None.
* Return : None.
*******************************************************************************/
// SPI1 GPIO 配置
static void SPI1_GPIO_Configuration(void) {
GPIO_InitTypeDef GPIO_InitStructure;
/*使能SPI1的时钟，这个接口的时钟挂在APB2上*/
RCC_APB2PeriphClockCmd(RCC_APB2Periph_GPIOA | RCC_APB2Periph_AFIO, ENABLE);
/* 配置SPI1的输出引脚: MOSI(PA.07)、SCK(PA.05)引脚 */
GPIO_StructInit(&GPIO_InitStructure);
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_7 | GPIO_Pin_5; //SPI_MOSI_PIN | SPI_SCK_PIN
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP; //push-pull alternate function output mode
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz; // the speed mode configer
GPIO_Init(GPIOA, &GPIO_InitStructure);
/* 配置SPI1的输入引脚:SPI1 MISO (PA.06) configuration */
GPIO_InitStructure.GPIO_Pin = GPIO_Pin_6; //SPI_MISO_PIN
GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
GPIO_Init(GPIOA, &GPIO_InitStructure);
}
/*******************************************************************************
* Function Name :SPI1_NVIC_Configuration
* Description : Configures the USART1 Configuration and enable set
* Input : None.
* Return : None.
*******************************************************************************/
//SPI1 NVIC 配置
static void SPI1_NVIC_Configuration(void) {
// NVIC init
#ifdef VEC_TAB_RAM
/* Set the Vector Table base location at 0x20000000 */
NVIC_SetVectorTable(NVIC_VectTab_RAM, 0x0);
#else /* VECT_TAB_FLASH */
/* Set the Vector Table base location at 0x08000000 */
NVIC_SetVectorTable(NVIC_VectTab_FLASH, 0x0);
#endif
#if 0
//配置中断优先级
NVIC_PriorityGroupConfig(NVIC_PriorityGroup_1);
NVIC_InitTypeDef NVIC_InitStructure;
/* Enable SPI1 Interrupt */
NVIC_InitStructure.NVIC_IRQChannel = SPI1_IRQChannel; /****SPI1_IRQChannel**/
NVIC_InitStructure.NVIC_IRQChannelPreemptionPriority = 1;
NVIC_InitStructure.NVIC_IRQChannelSubPriority = 0;
NVIC_InitStructure.NVIC_IRQChannelCmd = ENABLE;
NVIC_Init(&NVIC_InitStructure);
#endif
}
/*******************************************************************************
* Function Name : SPI1_Configuration
* Description : Configures the SPI1 Configuration and enable set
* Input : None.
* Return : None.
*******************************************************************************/
// SPI1 的配置
static void SPI1_Configuration(void) {
SPI_InitTypeDef SPI_InitStructure;
RCC_APB2PeriphClockCmd(RCC_APB2Periph_SPI1, ENABLE);
SPI_StructInit(&SPI_InitStructure);
/** SPI1 Configuration ****************/
SPI_InitStructure.SPI_Direction = SPI_Direction_2Lines_FullDuplex;/****全双工模式****/
SPI_InitStructure.SPI_Mode = SPI_Mode_Master; /****主模式********/
SPI_InitStructure.SPI_DataSize = SPI_DataSize_8b; /**数据长度为1字节**/
SPI_InitStructure.SPI_FirstBit = SPI_FirstBit_MSB; /**每个字节高位在前**/
SPI_InitStructure.SPI_CPOL = SPI_CPOL_Low; /**空闲时处于低电平**/
/**SPI_InitStructure.SPI_CPHA = SPI_CPHA_2Edge; **/ /**从第二个时钟周期开始采样*/
SPI_InitStructure.SPI_CPHA = SPI_CPHA_1Edge; /***从第一个时钟周期开始采样**/
SPI_InitStructure.SPI_NSS = SPI_NSS_Soft;
SPI_InitStructure.SPI_BaudRatePrescaler = SPI_BaudRatePrescaler_8;
SPI_InitStructure.SPI_CRCPolynomial = 7;
SPI_Init(SPI1, &SPI_InitStructure);
/* Enable SPI1 CRC calculation */
//SPI_CalculateCRC(SPI_USING, DISABLE); //使能RCC计算
//SPI_I2S_ITConfig(SPI_USING, SPI_I2S_IT_RXNE, DISABLE); //关闭接收中断，
//SPI_I2S_ITConfig(SPI_USING, SPI_I2S_IT_TXE, DISABLE); //关闭发送中断
SPI_Cmd(SPI1, ENABLE); //使能SPI1
}
void usart_putc(u8 ch) {
while( USART_GetFlagStatus(USART1, USART_FLAG_TXE) == RESET );
USART_SendData(USART1, ch);
}
void usart_puts(u8 str[]) {
while(*str != '\0' ) {
usart_putc(* str++);
}
}
void usart_println(void) {
usart_putc('\n');
usart_putc('\r');
}
void usart_cls() {
usart_putc(0x0c);
usart_putc(0x0c);
}
void usart_printArray( u8 * array, u32 arraySize) {
for(int i=0; i<arraySize; i++) {
usart_putc(* array++);
}
}
void USART_EXTI_DoIt(){
if( USART_GetFlagStatus(USART1, USART_FLAG_RXNE) == SET ) {
u8 ch = USART_ReceiveData(USART1);
USART_SendData(USART1, ch);
while( USART_GetFlagStatus(USART1, USART_FLAG_TXE) == RESET );
if(ch == '\r') {
USART_SendData(USART1, '\n');
while( USART_GetFlagStatus(USART1, USART_FLAG_TXE));
}
}
}
/* ------------End of private Configuration fuction for SPI-------------------*/
/***--------------------------Expired functions--------------------------------------*/
/******************* (C) COPYRIGHT 2011 SDUEM *****END OF FILE****/
3. 对无线模块nrf905se测试的主函数：
/******************** (C) COPYRIGHT 2011 SDU EMLIB ********************
* File Name : main.c
* Author : wzb@sdu
* Version : V1.1.1
* Date : 05/24/2011
* Description : USART1 communictate with pc AND NRF905SE.
********************************************************************************/
/* Includes ------------------------------------------------------------------*/
#include "hw_config.h"
#include "nrf905.h"
/*************************************************************************
* Function Name: main
* Parameters: none
*
* Return: none
*
* Description: main
*
*************************************************************************/
void main(void)
{
#ifdef DEBUG
debug();
#endif
RCC_Configuration();
USART_Configuration();
SPI_Configuration();
NRF905SE_Configuration();
// send packet
#if 1
u8 tx_array[4];
u8 rx_array[4];
//NRF905SE_GetRxAddress(rx_array, 4);
//NRF905SE_GetTxAddress(tx_array, 4);
NRF905SE_GetRxAddress(rx_array, NRF905SE_GetRxAddressSize());
NRF905SE_GetTxAddress(tx_array, NRF905SE_GetTxAddressSize());
usart_cls();
usart_puts("我是发送者， 我的地址是: ");
usart_printArray(rx_array, NRF905SE_GetRxAddressSize());
usart_println();
usart_puts("this is the NRF905SE transfer for send data, its info are as follows: ");
usart_println();
usart_puts("我的接收地址： ");
usart_printArray(rx_array, NRF905SE_GetRxAddressSize());
usart_println();
usart_puts("我的向目标地址：");
usart_printArray(tx_array, NRF905SE_GetTxAddressSize());
usart_puts("发送数据");
usart_println();
//NRF905SE_SendPacket(NRF905SE_TxBuffer, NRF905SE_BufferSize); /*****发送32字节的数据包*****/
u8 n = 48;
u8 payload_array[32];
u8 payloadSize = NRF905SE_GetTxPayloadSize();
//NRF905SE_SendPacket(NRF905SE_TxBuffer, NRF905SE_GetTxPayloadSize());
NRF905SE_SendPacket(NRF905SE_TxBuffer, payloadSize);
while(1) {
if(n== 58) {
n -= 10;
usart_println();
}
usart_puts("发包：(");
usart_putc(n++);
usart_puts(")");
NRF905SE_GetTxPayload( payload_array, payloadSize);
usart_printArray(payload_array, payloadSize);
usart_println();
if(n %2 == 0) {
for(int i=0; i<payloadSize; i++) {
payload_array[i] -= 1;
}
}
else {
for(int i=0; i<payloadSize; i++) {
payload_array[i] += 1;
}
}
NRF905SE_SendPacket(payload_array, payloadSize);
//NRF905SE_SetTxPayload(payload_array, payloadSize);
//NRF905SE_SendData();
/*
for(u32 i=0; i<1000; i++) {
for(u32 j = 0; j<1000; j++)
for(u32 k=0; k<5; k++);
}
*/
}
#endif
//receive data
#if 0
NRF905SE_SetRxAddress("1234", 4);
NRF905SE_SetTxAddress("0123", 4);
u8 tx_array[4];
u8 rx_array[4];
NRF905SE_GetRxAddress(rx_array, 4);
NRF905SE_GetTxAddress(tx_array, 4);
usart_cls();
usart_puts("this is the NRF905SE transfer for receive data, its info are as follows: ");
usart_println();
usart_puts("我的接收地址： ");
usart_printArray(rx_array, 4);
usart_println();
usart_puts("我的目标发送地址：");
usart_printArray(tx_array, 4);
usart_println();
usart_puts("我开始接受来自发射器：");
usart_printArray(tx_array, 4);
usart_puts("发送来的数据：");
usart_println();
u8 payloadSize = NRF905SE_GetRxPayloadSize();
u8 n = 48;
while(1) {
/*****发送32字节的数据包*****/
if(n== 58 ) {
n -= 10;
usart_println();
}
if(NRF905SE_ReceivePacket(NRF905SE_RxBuffer, payloadSize) ) {
usart_puts("收包(");
usart_putc(n++);
usart_puts("): ");
usart_printArray(NRF905SE_RxBuffer, payloadSize);
usart_println();
}
}
#endif
while(1);
}
#ifdef DEBUG
/*******************************************************************************
* Function Name : assert_failed
* Description : Reports the name of the source file and the source line number
* where the assert_param error has occurred.
* Input : - file: pointer to the source file name
* - line: assert_param error line source number
* Output : None
* Return : None
*******************************************************************************/
void assert_failed(u8* file, u32 line)
{
volatile bool Flag = TRUE;
/* User can add his own implementation to report the file name and line number,
ex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
/* Infinite loop */
while (Flag )
{
}
}
#endif
4.备注：以上代码是基于stm32固件库的，具体的端口配置，具体的板子相关。代码是基于IAR开发的。有时间的话，我会提供整个开发工程的下载！
2万+
被折叠的 条评论
为什么被折叠?
到【灌水乐园】发言
