详解配置交换机多生成树MSTP+VRRP 的典型组网

详解配置交换机多生成树MSTP+VRRP 的典型组网

组网：

1. 这是一个由三台交换机组成的倒三角型二层交换网络；网络中有4个VLAN：10、20、30、40；接口编号如图所示；SW3为接入层交换机，SW1、SW2为汇聚层交换机；

2. VLAN10对应的网段为192.168.10.0/24；VLAN20对应的网段为192.168.20.0/24；VLAN30对应的网段为192.168.30.0/24；VLAN40对应的网段为192.168.40.0/24；各VLAN的网关均为192.168.x.254的地址，该地址为VRRP组的虚拟地址。

现在要求：

1. 由于网络中VLAN较多，并且存在二层环路，因此使用MSTP实现环路避免，同时实现负载分担。要求VLAN10、VLAN20的流量主走SW1-SW3这一侧链路，VLAN30、VLAN40的流量主走SW2-SW3这一侧链路；

2. 为了提高网络的网关层冗余能力，在SW1及SW2的vlanif10、vlanif20、vlanif30、vlanif40上部署VRRP，一共4组。

二、IP设置：

PC1:192.168.10.1/24,vlan10

PC2:192.168.20.1/24,vlan20

PC3:192.168.30.1/24,vlan30

PC4:192.168.40.1/24,vlan40

SW1:

vlanif10:192.168.10.253/24,virtual-ip:192.168.10.254/24,master

Vlanif20:192.168.20.253/24,virtual-ip:192.168.20.254/24,master

Vlanif30:192.168.30.253/24,virtual-ip:192.168.30.254/24,backup

Vlanif40:192.168.40.253/24,virtual-ip:192.168.40.254/24,backup

SW2:

vlanif10:192.168.10.252/24,virtual-ip:192.168.10.254/24,backup

Vlanif20:192.168.20.252/24,virtual-ip:192.168.20.254/24,backup

Vlanif30:192.168.30.252/24,virtual-ip:192.168.30.254/24,master

Vlanif40:192.168.40.252/24,virtual-ip:192.168.40.254/24,master

三、配置步骤：

由于网络中VLAN较多，并且存在二层环路因此使用MSTP实现环路避免，同时实现负载分担。将VLAN10、20映射到MSTP实例1；将VLAN30、40映射到MSTP实例2。MSTP实例1阻塞掉的端口为SW3的GE0/0/22，实例2阻塞掉的端口为SW3的GE0/0/21。换句话说就是SW1配置为实例1的主根、实例2的次根，而SW2配置为实例2的主根、实例1的次根。这个案例中必须确保VRRP的Master及Backup与MSTP的主、备根重叠。也就是说SW1是MSTP实例1的主根，同时它是vlanif10及vlanif20的VRRP Master，而SW2是MSTP实例2的主根，同时它是vlanif30及vlanif40的VRRP Master。

SW3的配置如下：

#在SW3上创建VLAN，并将接口加入相应的VLAN：

[SW3] vlan batch 10 20 30 40

[SW3] interface GigabitEthernet0/0/21

[SW3-GigabitEthernet0/0/21] port link-type trunk

[SW3-GigabitEthernet0/0/21] port trunk allow-pass vlan 10 20 30 40

[SW3] interface GigabitEthernet0/0/22

[SW3-GigabitEthernet0/0/22] port link-type trunk

[SW3-GigabitEthernet0/0/22] port trunk allow-pass vlan 10 20 30 40

#配置MSTP，将vlan10 20映射到实例1，将vlan30 40映射到实例2。在SW3上，MSTP实例1及实例2的优先级保持默认32768：

[SW3] stp mode mstp

[SW3] stp region-configuration

[SW3-mst-region] region-name huawei

#配置MSTP域名

[SW3-mst-region] instance 1 vlan 10 20

#将VLAN10、20映射到实例1

[SW3-mst-region] instance 2 vlan 30 40

#将VLAN30、40映射到实例2

[SW3-mst-region] active region-configuration #激活配置

[SW3-mst-region] quit

[SW3] stp enable

SW1的配置如下：

[SW1] vlan batch 10 20 30 40

[SW1] interface GigabitEthernet0/0/24

[SW1-GigabitEthernet0/0/24] port link-type trunk

[SW1-GigabitEthernet0/0/24] port trunk allow-pass vlan 10 20 30 40

[SW1] interface GigabitEthernet0/0/21

[SW1-GigabitEthernet0/0/21] port link-type trunk

[SW1-GigabitEthernet0/0/21] port trunk allow-pass vlan 10 20 30 40

#配置MSTP，将VLAN10 20映射到实例1，将VLAN30 40映射到实例2。将SW1的MSTP设置为实例1的主根，实例2的次根：

[SW1] stp mode mstp

[SW1] stp region-configuration

[SW1-mst-region] region-name huawei

[SW1-mst-region] instance 1 vlan 10 20

[SW1-mst-region] instance 2 vlan 30 40

[SW1-mst-region] active region-configuration

[SW1-mst-region] quit

[SW1] stp instance 1 root primary

[SW1] stp instance 2 root secondary

[SW1] stp enable

#配置vlanif10、vlanif20、vlanif30、vlanif40，分别加入VRRP组10,20,30,40。其中SW1为VRRP组10及20的Master，为组30及40的Backup：

[SW1] interface Vlanif 10

[SW1-vlanif10] ip address 192.168.10.253 255.255.255.0

[SW1-vlanif10] vrrp vrid 10 virtual-ip 192.168.10.254

[SW1-vlanif10] vrrp vrid 10 priority 120

[SW1] interface Vlanif 20

[SW1-vlanif20] ip address 192.168.20.253 255.255.255.0

[SW1-vlanif20] vrrp vrid 20 virtual-ip 192.168.20.254

[SW1-vlanif20] vrrp vrid 20 priority 120

[SW1] interface Vlanif 30

[SW1-vlanif30] ip address 192.168.30.253 255.255.255.0

[SW1-vlanif30] vrrp vrid 30 virtual-ip 192.168.30.254

[SW1] interface Vlanif 40

[SW1-vlanif40] ip address 192.168.40.253 255.255.255.0

[SW1-vlanif40] vrrp vrid 40 virtual-ip 192.168.40.254

SW2的配置如下：

[SW2] vlan batch 10 20 30 40

[SW2] interface GigabitEthernet0/0/24

[SW2-GigabitEthernet0/0/24] port link-type trunk

[SW2-GigabitEthernet0/0/24] port trunk allow-pass vlan 10 20 30 40

[SW2] interface GigabitEthernet0/0/22

[SW2-GigabitEthernet0/0/22] port link-type trunk

[SW2-GigabitEthernet0/0/22] port trunk allow-pass vlan 10 20 30 40

#配置MSTP，将VLAN10 20映射到实例1，将VLAN30 40映射到实例2。将SW2的MSTP设置为实例2的主根，实例1的次根：

[SW2] stp mode mstp

[SW2] stp region-configuration

[SW2-mst-region] region-name huawei

[SW2-mst-region] instance 1 vlan 10 20

[SW2-mst-region] instance 2 vlan 30 40

[SW2-mst-region] active region-configuration

[SW2-mst-region] quit

[SW2] stp instance 1 root secondary

[SW2] stp instance 2 root primary

[SW2] stp enable

#配置vlanif10、vlanif20、vlanif30、vlanif40，分别加入VRRP组10,20,30,40。其中SW1为VRRP组30及40的Master，为组10及20的Backup

[SW2] interface Vlanif 10

[SW2-vlanif10] ip address 192.168.10.252 255.255.255.0

[SW2-vlanif10] vrrp vrid 10 virtual-ip 192.168.10.254

[SW2] interface Vlanif 20

[SW2-vlanif20] ip address 192.168.20.252 255.255.255.0

[SW2-vlanif20] vrrp vrid 20 virtual-ip 192.168.20.254

[SW2] interface Vlanif 30

[SW2-vlanif30] ip address 192.168.30.252 255.255.255.0

[SW2-vlanif30] vrrp vrid 30 virtual-ip 192.168.30.254

[SW2-vlanif30] vrrp vrid 30 priority 120

[SW2] interface Vlanif 40

[SW2-vlanif40] ip address 192.168.40.252 255.255.255.0

[SW2-vlanif40] vrrp vrid 40 virtual-ip 192.168.40.254

[SW2-vlanif40] vrrp vrid 40 priority 120

完成配置后，各VLAN的用户都能够ping通自己的网关，在SW3上看看：

<SW3>dis stp bri

MSTID Port Role STP State Protection

0 GigabitEthernet0/0/1 DESI FORWARDING NONE

0 GigabitEthernet0/0/2 DESI FORWARDING NONE

0 GigabitEthernet0/0/3 DESI LEARNING NONE

0 GigabitEthernet0/0/4 DESI LEARNING NONE

0 GigabitEthernet0/0/21 DESI FORWARDING NONE

0 GigabitEthernet0/0/22 ROOT FORWARDING NONE

1 GigabitEthernet0/0/1 DESI FORWARDING NONE

1 GigabitEthernet0/0/2 DESI FORWARDING NONE

1 GigabitEthernet0/0/21 ROOT FORWARDING NONE

1 GigabitEthernet0/0/22 ALTE DISCARDING NONE

2 GigabitEthernet0/0/3 DESI LEARNING NONE

2 GigabitEthernet0/0/4 DESI LEARNING NONE

2 GigabitEthernet0/0/21 ALTE DISCARDING NONE

2 GigabitEthernet0/0/22 ROOT FORWARDING NONE

在SW3上我们看到，MSTP实例1中被Block掉的端口是GE0/0/22口；MSTP实例2中被Block掉的端口是GE0/0/21，符合需求。再去SW1上看看VRRP组的状态：

<SW1>display vrrp bri

VRID State Interface Type Virtual IP

----------------------------------------------------------------

10 Master Vlanif10 Normal 192.168.10.254

20 Master Vlanif20 Normal 192.168.20.254

30 Backup Vlanif30 Normal 192.168.30.254

40 Backup Vlanif40 Normal 192.168.40.254

----------------------------------------------------------------

Total:4 Master:2 Backup:2 Non-active:0

从上述输出可以看出，SW1为VRRP组10及组20的Master，同时也为VRRP组30和组40的Backup。

<SW2>display vrrp bri

VRID State Interface Type Virtual IP

----------------------------------------------------------------

10 Backup Vlanif10 Normal 192.168.10.254

20 Backup Vlanif20 Normal 192.168.20.254

30 Master Vlanif30 Normal 192.168.30.254

40 Master Vlanif40 Normal 192.168.40.254

----------------------------------------------------------------

Total:4 Master:2 Backup:2 Non-active:0

而SW2则正好相反。如此一来，VLAN10及VLAN20用户访问外网的流量将SW3-SW1的路径转发，VLAN30及VLAN40用户访问外网的流量将SW2-SW1的路径转发。当网络中的链路发生故障时，将会启用另一条备份链路，业务不受影响。

四、SW3的主要配置文件：

#

sysname SW3

#

vlan batch 10 20 30 40

#

stp region-configuration

region-name huawei

instance 1 vlan 10 20

instance 2 vlan 30 40

active region-configuration

#

interface GigabitEthernet0/0/1

port link-type access

port default vlan 10

#

interface GigabitEthernet0/0/2

port link-type access

port default vlan 20

#

interface GigabitEthernet0/0/3

port link-type access

port default vlan 30

#

interface GigabitEthernet0/0/4

port link-type access

port default vlan 40

#

interface GigabitEthernet0/0/21

port link-type trunk

port trunk allow-pass vlan 10 20 30 40

#

interface GigabitEthernet0/0/22

port link-type trunk

port trunk allow-pass vlan 10 20 30 40

#

return

五、SW1的主要配置文件：

<SW1>disp cu

#

sysname SW1

#

vlan batch 10 20 30 40

#

stp instance 1 root primary

stp instance 2 root secondary

#

stp region-configuration

region-name huawei

instance 1 vlan 10 20

instance 2 vlan 30 40

active region-configuration

#

interface Vlanif10

ip address 192.168.10.253 255.255.255.0

vrrp vrid 10 virtual-ip 192.168.10.254

vrrp vrid 10 priority 120

#

interface Vlanif20

ip address 192.168.20.253 255.255.255.0

vrrp vrid 20 virtual-ip 192.168.20.254

vrrp vrid 20 priority 120

#

interface Vlanif30

ip address 192.168.30.253 255.255.255.0

vrrp vrid 30 virtual-ip 192.168.30.254

#

interface Vlanif40

ip address 192.168.40.253 255.255.255.0

vrrp vrid 40 virtual-ip 192.168.40.254

#

interface MEth0/0/1

#

interface GigabitEthernet0/0/1

port link-type trunk

port trunk allow-pass vlan 10 20 30 40

#

interface GigabitEthernet0/0/2

port link-type trunk

port trunk allow-pass vlan 10 20 30 40

#

return

六、SW2的主要配置文件：

#

sysname SW2

#

vlan batch 10 20 30 40

#

stp instance 1 root secondary

stp instance 2 root primary

#

stp region-configuration

region-name huawei

instance 1 vlan 10 20

instance 2 vlan 30 40

active region-configuration

#

interface Vlanif10

ip address 192.168.10.252 255.255.255.0

vrrp vrid 10 virtual-ip 192.168.10.254

#

interface Vlanif20

ip address 192.168.20.252 255.255.255.0

vrrp vrid 20 virtual-ip 192.168.20.254

#

interface Vlanif30

ip address 192.168.30.252 255.255.255.0

vrrp vrid 30 virtual-ip 192.168.30.254

vrrp vrid 30 priority 120

#

interface Vlanif40

ip address 192.168.40.252 255.255.255.0

vrrp vrid 40 virtual-ip 192.168.40.254

vrrp vrid 40 priority 120

#

interface MEth0/0/1

#

interface GigabitEthernet0/0/1

port link-type trunk

port trunk allow-pass vlan 10 20 30 40

#

interface GigabitEthernet0/0/2

port link-type trunk

port trunk allow-pass vlan 10 20 30 40

#

return