如何编写skyeye

 

#--------------------------------------------------------------------------------
# memmap.conf and skyeye.conf are all skyeye's hareware coinfigure files.
# memmap.conf is for skyeye-v0.2.5-
# skyeye.conf is for skyeye-v0.2.5+
# usually you needn't to chang them.
# for example, a AT91's configure file is shown below:
#--------------------------------------------------------------------------------
# below is the cpu config info
# cpu maybe arm7tdmi or arm720t
cpu: arm7tdmi
#--------------------------------------------------------------------------------
# below is the machine(develop board) config info
# machine(develop board) maybe at91 or ep7312
mach: at91
#-------------------------------------------------------------------------------
#NOTICE: this parameter is useless for skyeye-V0.3.1+
# have 7 memory bank (include RAM, ROM, mapped IO space)
# below is the memory config info
mem_num: 7
# map=M means ram/rom, map=I means mapped IO space,
# type=RW means can be read or written,
# type=R means read only,
# addr=0x..... means the mem bank's beginning address,
# size=0x..... means the mem bank's memory size,  
# file=... is the filesystem image file, used for uclinux4skyeye or armlinux4skyeye
mem_bank: map=M, type=RW, addr=0x00000000, size=0x00004000
mem_bank: map=M, type=RW, addr=0x01000000, size=0x00400000
mem_bank: map=M, type=R, addr=0x01400000, size=0x00400000, file=./boot.rom
mem_bank: map=M, type=RW, addr=0x02000000, size=0x00400000
mem_bank: map=M, type=RW, addr=0x02400000, size=0x00008000
mem_bank: map=M, type=RW, addr=0x04000000, size=0x00400000
mem_bank: map=I, type=RW, addr=0xf0000000, size=0x10000000
#now, add more options on mem_bank
mem_bank: map=M, type=RW, addr=0x10000000, size=0x00000800, file=./loader.bin,boot=yes
#start binary program at 0x100000000
#----------------------------------------------------------------------------------
# below is the net config info
# state=on/off means simulated NIC is wired or not,
# mac=.... means the mac addr in simulated NIC,
# ethmod=tuntap/vnet means the virtual driver used in host evnironment,
# hostip=... means the ip address in host environment to interactive with skyeye.
# format: state=on/off mac=xx:xx:xx:xx:xx:xx ethmod=tuntap/vnet hostip=dd.dd.dd.dd
# *********NOTICE**********
#If you run two more skyeyes at the same time,
# please use different skyeye.conf for each skyeye instance, and only one
# skyeye run first and related skyeye.conf content has hostip value:
#      ......
#      net: ... ethmod=vnet, hostip=ddd.ddd.ddd.ddd
#   other skyeye.conf should has content(hostip[0] should be 0):
#      ......
#      net: ... ethmod=vnet, hostip=0.ddd.ddd.ddd
net: state=on, mac=0:4:3:2:1:f, ethmod=tuntap, hostip=10.0.0.1
#------------------------------------------------------------------------------------
#uart: use it to read/write characters in another terminal
#now you can use them to connect real serial port.
#you can add an option to skyeye.conf as below:
uart: fd_in=/dev/ttyS0, fd_out=/dev/ttyS0
#then use a terminal connect host's COM1, you can see the output in the terminal.
#-----------------------------------------------------------------------------------
#add log parameter which is used to recode the instr. flow and regs when
#program are running.
log: logon=0, logfile=/tmp/sk1.log, start=100000, end=200000
#logon = 0 or 1 0:doesn't log, 1 do log
#logfile: the filename which have the log info
#start: the start point of instruction flow to log, should >=0
#end:    the end    point of instructio flow to log