Haiwei ET128 Linux

Haiwei ET128 Linux

2009年09月01日 星期二 18:09

everest0.6 安装 HuaWei ET128 3G上网卡 前天去移动办了个随e行G3上网卡，回来一看，只有windows驱动和软件，但我平时多数时间在linux下，用google扒啦了一下，还真有配置方法～，现简化一下，共享之～～ 上网卡型号：HUAWEI ET128 系统版本：Qomo 0.6 GCC44 （2.6.29.4-40） 1、首先下载安装usb_modeswitch： #wget http://www.draisberghof.de/usb_modeswitch/usb_modeswitch-1.0.2.tar.bz2 解压，编译安装： #tar xjvf usb_modeswitch-1.0.2.tar.bz2 #cd usb_modeswitch-1.0.2 #make install 然后编辑usb_modeswitch.conf配置文件： #vi /etc/usb_modeswitch.conf 该配置文件内有世面上绝大多数的无线上网卡配置信息，但没有华为ET128硬件的相关信息(可能比较新吧)，需要手工添加如下内容进去 ###################################### # Huawei ET128 # # Contributor: Dale Lane DefaultVendor= 0x12d1; DefaultProduct= 0x1da1 # choose one of these: DetachStorageOnly=0 HuaweiMode=1 ###################################### 其中注意红色部分，是厂商信息和硬件信息，可以通过lsusb命令查看获取： #lsusb Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 002: ID 0b05:b700 ASUSTek Computer, Inc. Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 04fc:0003 Sunplus Technology Co., Ltd CM1092 Optical Scroller Mouse Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 012: ID 12d1:1da1 Huawei Technologies Co., Ltd. Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub 2、配置完成后，执行usb_modeswitch -W命令创建tty设备 # usb_modeswitch -W 再查看dmesg信息，如果有生成新的ttyACMx设备即表示成功 #dmesg cdc_acm 1-2:3.1: ttyACM0: USB ACM device cdc_acm 1-2:3.3: ttyACM1: USB ACM device cdc_acm 1-2:3.5: ttyACM2: USB ACM device 3、安装wvdail拨号工具，源里有（据说可以在NetworkManager下使用，但我没配置成功，望达人指教） #yum install wvdial 执行wvdialconf扫描硬件并生成配置文件： #wvdialconf 编辑/etc/wvdial.conf配置文件加入如下拨号配置信息： ;######################## Phone = *99***1# Password = any Username = any Stupid Mode = 1 4、拨号： #wvdial --> Ignoring malformed input line: ";########################" --> WvDial: Internet dialer version 1.60 --> Cannot get information for serial port. --> Initializing modem. --> Sending: ATZ ATZ OK --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 OK --> Modem initialized. --> Sending: ATDT*99***1# --> Waiting for carrier. ATDT*99***1# CONNECT 2800000 --> Carrier detected. Starting PPP immediately. --> Starting pppd at Mon Jul 27 16:31:44 2009 --> Pid of pppd: 3667 --> Using interface ppp0 --> pppd: ??[06][08][10]?[06][08] --> pppd: ??[06][08][10]?[06][08] --> pppd: ??[06][08][10]?[06][08] --> pppd: ??[06][08][10]?[06][08] --> pppd: ??[06][08][10]?[06][08] --> local IP address 10.140.68.38 --> pppd: ??[06][08][10]?[06][08] --> remote IP address 192.200.1.21 --> pppd: ??[06][08][10]?[06][08] --> primary   DNS address 221.130.33.60 --> pppd: ??[06][08][10]?[06][08] --> secondary DNS address 221.130.33.52 --> pppd: ??[06][08][10]?[06][08] OK,冲浪去吧，关闭只需crtl + c 想方便可以写个脚本放到桌面： #!/bin/sh /usr/sbin/usb_modeswitch -W sleep 5 echo "nameserver 202.106.0.20" >/etc/resolv.con konsole -e /usr/bin/wvdial 每次插上U盘，然后双击该脚本，断线时按ctrl + c即可 Ubuntu 9.04 安装 HuaWei ET128 3G上网卡 1. 把HuaWei 3G上网卡insert到电脑的USB port. #dmesg | grep HUAWEI [ 4411.960220] scsi 10:0:0:0: CD-ROM HUAWEI Mobile CMCC CD 1.25 PQ: 0 ANSI: 0 # lsusb | grep Huawei Bus 005 Device 007: ID 12d1:1d09 Huawei Technologies Co., Ltd. 这里需要记下ID 后面的. 2. 下载安装usb_modeswitch . 下载地址:http://www.draisberghof.de/usb_modeswitch 安装请看软件的README文件. 拷贝编译完的usb_modeswitch 到/sbin下 #usb_modeswitch -h 查看使用方法 #usb_modeswitch -W 最好执行一下,查看一下设置 print all settings before running 3.需要修改 /etc/wvdial.conf 配置文件. Please see my config file: [Dialer Defaults] Init1 = ATZ Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 Modem Type = USB Modem Baud = 460800 ;Baud = 9216000 New PPPD = yes Modem = /dev/ttyACM2 #这里我是安装了gnome-ppp自动识别出来的 ;Modem = /dev/ttyUSB0 ISDN = 0 ; Phone = <Target Phone Number> ; Password = <Your Password> ; Username = <Your Login Name> Phone = *99***1# Password = any Username = any Stupid Mode = 1 4.拔号 ＄sudo wvdial 可能需要等一会，你会看到 heqiang@heqiang-laptop:~$ sudo wvdial --> WvDial: Internet dialer version 1.60 --> Cannot get information for serial port. --> Initializing modem. --> Sending: ATZ ATZ OK --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 OK --> Modem initialized. --> Sending: ATDT*99***1# --> Waiting for carrier. ATDT*99***1# CONNECT 236800 --> Carrier detected. Starting PPP immediately. --> Starting pppd at Thu Jun 11 14:17:31 2009 --> Pid of pppd: 19674 --> Using interface ppp0 --> pppd: п��P)J[08]@)J[08] --> pppd: п��P)J[08]@)J[08] --> pppd: п��P)J[08]@)J[08] --> pppd: п��P)J[08]@)J[08] --> pppd: п��P)J[08]@)J[08] --> pppd: п��P)J[08]@)J[08] --> pppd: п��P)J[08]@)J[08] --> local IP address 10.68.212.84 --> pppd: п��P)J[08]@)J[08] --> remote IP address 192.200.1.21 --> pppd: п��P)J[08]@)J[08] --> primary DNS address 221.130.33.52 --> pppd: п��P)J[08]@)J[08] --> secondary DNS address 221.130.33.60 --> pppd: п��P)J[08]@)J[08] 说明连接成功了! $sudo ifconfig ppp0 ppp0 Link encap:点对点协议 inet 地址:10.68.212.84 点对点:192.200.1.21 掩码:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1500 跃点数:1 接收数据包:18798 错误:0 丢弃:0 过载:0 帧数:0 发送数据包:14731 错误:0 丢弃:0 过载:0 载波:0 碰撞:0 发送队列长度:3 接收字节:23233292 (23.2 MB) 发送字节:1357737 (1.3 MB) 5. 这里写的比较单，相信你能成功. 不行的话，下面的希望有用： 一开始插上3G卡的时候，lsusb显示为： ubuntu@Ubuntu:~$ lsusb | grep Huawei Bus 002 Device 002: ID 12d1:1da1 Huawei Technologies Co., Ltd. 这时候，修改/etc/usb_modeswitch.conf： DefaultVendor= 0x12d1 DefaultProduct= 0x1da1 TargetVendor= 0x12d1 TargetProduct= 0x1da1 HuaweiMode=1 执行sudo usb_modeswitch -W 令修改生效。这时候 ubuntu@Ubuntu:~$ lsusb | grep Huawei Bus 002 Device 002: ID 12d1:1d09 Huawei Technologies Co., Ltd. 会发现1da1变成了1d09. 然后再修改/etc/usb_modeswitch.conf DefaultVendor= 0x12d1 DefaultProduct= 0x1d09 TargetVendor= 0x12d1 TargetProduct= 0x1d09 ;HuaweiMode=1 再执行sudo usb_modeswitch -W令修改生效。 检查/dev/下面， 会出来ttyACM0, ttyACM1, 和ttyACM2. 然后再执行sudo wvdialconf自动生成配置文件 ubuntu@Ubuntu:~$ sudo wvdialconf Editing `/etc/wvdial.conf'. Scanning your serial ports for a modem. Modem Port Scan<*1>: S0 S1 S2 S3 WvModem<*1>: Cannot get information for serial port. ttyACM0<*1>: ATQ0 V1 E1 -- OK ttyACM0<*1>: ATQ0 V1 E1 Z -- OK ttyACM0<*1>: ATQ0 V1 E1 S0=0 -- OK ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK ttyACM0<*1>: Modem Identifier: ATI -- Manufacturer: HuaWei ttyACM0<*1>: Speed 4800: AT -- OK ttyACM0<*1>: Speed 9600: AT -- OK ttyACM0<*1>: Speed 19200: AT -- OK ttyACM0<*1>: Speed 38400: AT -- OK ttyACM0<*1>: Speed 57600: AT -- OK ttyACM0<*1>: Speed 115200: AT -- OK ttyACM0<*1>: Speed 230400: AT -- OK ttyACM0<*1>: Speed 460800: AT -- OK ttyACM0<*1>: Max speed is 460800; that should be safe. ttyACM0<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK WvModem<*1>: Cannot get information for serial port. ttyACM1<*1>: ATQ0 V1 E1 -- OK ttyACM1<*1>: ATQ0 V1 E1 Z -- OK ttyACM1<*1>: ATQ0 V1 E1 S0=0 -- OK ttyACM1<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK ttyACM1<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK ttyACM1<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK ttyACM1<*1>: Modem Identifier: ATI -- Manufacturer: HuaWei ttyACM1<*1>: Speed 4800: AT -- OK ttyACM1<*1>: Speed 9600: AT -- OK ttyACM1<*1>: Speed 19200: AT -- OK ttyACM1<*1>: Speed 38400: AT -- OK ttyACM1<*1>: Speed 57600: AT -- OK ttyACM1<*1>: Speed 115200: AT -- OK ttyACM1<*1>: Speed 230400: AT -- OK ttyACM1<*1>: Speed 460800: AT -- OK ttyACM1<*1>: Max speed is 460800; that should be safe. ttyACM1<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK WvModem<*1>: Cannot get information for serial port. ttyACM2<*1>: ATQ0 V1 E1 -- OK ttyACM2<*1>: ATQ0 V1 E1 Z -- OK ttyACM2<*1>: ATQ0 V1 E1 S0=0 -- OK ttyACM2<*1>: ATQ0 V1 E1 S0=0 &C1 -- OK ttyACM2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 -- OK ttyACM2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK ttyACM2<*1>: Modem Identifier: ATI -- Manufacturer: HuaWei ttyACM2<*1>: Speed 4800: AT -- OK ttyACM2<*1>: Speed 9600: AT -- OK ttyACM2<*1>: Speed 19200: AT -- OK ttyACM2<*1>: Speed 38400: AT -- OK ttyACM2<*1>: Speed 57600: AT -- OK ttyACM2<*1>: Speed 115200: AT -- OK ttyACM2<*1>: Speed 230400: AT -- OK ttyACM2<*1>: Speed 460800: AT -- OK ttyACM2<*1>: Max speed is 460800; that should be safe. ttyACM2<*1>: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 -- OK Found an USB modem on /dev/ttyACM0. Modem configuration written to /etc/wvdial.conf. ttyACM0<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0" ttyACM1<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0" ttyACM2<Info>: Speed 460800; init "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0" ubuntu@Ubuntu:~$ 再修改/etc/wvdial.conf中的相应部分就可以了。我的配置如下： [Dialer Defaults] Init1 = ATZ Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 Password = any Phone = *99***1# Modem Type = USB Modem Stupid Mode = 1 Baud = 460800 New PPPD = yes Modem = /dev/ttyACM0 ISDN = 0 username = any ; Phone = <Target Phone Number> ; Password = <Your Password> ; Username = <Your Login Name> 之后，就知道该怎么做了吧？ sudo wvdial就OK了。 ubuntu@Ubuntu:~$ sudo wvdial --> WvDial: Internet dialer version 1.60 --> Cannot get information for serial port. --> Initializing modem. --> Sending: ATZ ATZ OK --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 OK --> Modem initialized. --> Sending: ATDT*99***1# --> Waiting for carrier. ATDT*99***1# CONNECT 2800000 --> Carrier detected. Starting PPP immediately. --> Starting pppd at Mon Jun 22 11:11:50 2009 --> Pid of pppd: 4134 --> Using interface ppp0 --> local IP address 10.140.162.111 --> remote IP address 192.200.1.21 --> primary DNS address 221.130.33.60 --> secondary DNS address 221.130.33.52 OK了！ Fedora 10 安装 HuaWei ET128 3G上网卡   上网卡型号：HUAWEI ET128 系统版本： Fedora 10 1、首先下载安装usb_modeswitch： #wget http://www.draisberghof.de/usb_modeswitch/usb_modeswitch-1.0.2.tar.bz2 解压，编译安装： #tar xjvf usb_modeswitch-1.0.2.tar.bz2 #cd usb_modeswitch-1.0.2 #make install 然后编辑usb_modeswitch.conf配置文件： #vi /etc/usb_modeswitch.conf 该配置文件内有世面上绝大多数的无线上网卡配置信息，但没有华为ET128硬件的相关信息(可能比较新吧)，需要手工添加如下内容进去 ###################################### # Huawei ET128 # # Contributor: Dale Lane DefaultVendor= 0x12d1 DefaultProduct= 0x1da1     (这个要根据lsusb的输出更改) # choose one of these: DetachStorageOnly=0 HuaweiMode=1 ###################################### 其中注意红色部分，是厂商信息和硬件信息，可以通过lsusb命令查看获取： #lsusb Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub Bus 004 Device 002: ID 0b05:b700 ASUSTek Computer, Inc. Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 002 Device 002: ID 04fc:0003 Sunplus Technology Co., Ltd CM1092 Optical Scroller Mouse Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub Bus 001 Device 012: ID 12d1:1da1 Huawei Technologies Co., Ltd. Bus 001 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub 2、配置完成后，执行usb_modeswitch -W命令创建tty设备 # usb_modeswitch -W 再查看dmesg信息，如果有生成新的ttyACMx 设备即表示成功 #dmesg cdc_acm 1-2:3.1: ttyACM0 : USB ACM device cdc_acm 1-2:3.3: ttyACM1 : USB ACM device cdc_acm 1-2:3.5: ttyACM2 : USB ACM device 3、安装wvdail拨号工具，源里有（据说可以在NetworkManager下使用，但我没配置成功，望达人指教） #yum install wvdial 执行wvdialconf扫描硬件并生成配置文件： #wvdialconf 编辑/etc/wvdial.conf配置文件加入如下拨号配置信息： ;######################## Phone = *99***1# Password = any Username = any Stupid Mode = 1 4、拨号： #wvdial --> Ignoring malformed input line: ";########################" --> WvDial: Internet dialer version 1.60 --> Cannot get information for serial port. --> Initializing modem. --> Sending: ATZ ATZ OK --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0 ^MODE: 15 OK --> Modem initialized. --> Sending: ATDT*99***1# --> Waiting for carrier. ATDT*99***1# CONNECT 2800000 --> Carrier detected. Starting PPP immediately. --> Starting pppd at Mon Jul 20 16:14:15 2009 --> Pid of pppd: 3267 --> Using interface ppp0 --> pppd: � � [06][08][10]� [06][08] --> pppd: � � [06][08][10]� [06][08] --> pppd: � � [06][08][10]� [06][08] --> pppd: � � [06][08][10]� [06][08] --> pppd: � � [06][08][10]� [06][08] --> local IP address 10.140.50.6 --> pppd: � � [06][08][10]� [06][08] --> remote IP address 192.200.1.21 --> pppd: � � [06][08][10]� [06][08] --> primary   DNS address 221.130.33.60 --> pppd: � � [06][08][10]� [06][08] --> secondary DNS address 221.130.33.52 --> pppd: � � [06][08][10]� [06][08] OK,冲浪去吧，关闭只需crtl + c 注意：        应当先禁用当前的网卡        如：ifconfig eth0 down