STM32F103和STM32F030 SPI-miso配置不同点

最新推荐文章于 2024-10-11 20:46:16 发布

yule

最新推荐文章于 2024-10-11 20:46:16 发布

阅读量3.8k

点赞数 6

分类专栏： STM32 文章标签： STM32 SPI MISO

本文链接：https://blog.csdn.net/yule/article/details/102755151

版权

STM32 专栏收录该内容

3 篇文章 0 订阅

订阅专栏

在调试STM32F103和STM32F030的SPI时，发现两者的MISO配置不同，

STM32F103:

/**SPI1 GPIO Configuration
PA5 ------> SPI1_SCK
PA6 ------> SPI1_MISO
PA7 ------> SPI1_MOSI
*/
GPIO_InitStruct.Pin = GPIO_PIN_5|GPIO_PIN_7;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

GPIO_InitStruct.Pin = GPIO_PIN_6;
GPIO_InitStruct.Mode = GPIO_MODE_INPUT;
GPIO_InitStruct.Pull = GPIO_NOPULL;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

STM32F030:

/**SPI1 GPIO Configuration
PA5 ------> SPI1_SCK
PA6 ------> SPI1_MISO
PA7 ------> SPI1_MOSI
*/
GPIO_InitStruct.Pin = GPIO_PIN_5|GPIO_PIN_6|GPIO_PIN_7;
GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
GPIO_InitStruct.Pull = GPIO_NOPULL;
GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH;
GPIO_InitStruct.Alternate = GPIO_AF0_SPI1;
HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);

其中区别在于, F103的MISO要配置成输入（GPIO_MODE_INPUT), 而F030的要配置成复用(GPIO_MODE_AF_PP)，的确非常奇怪。后来查询RM得知，F103的配置是：

CNFy[1:0]: Port x configuration bits (y= 0 .. 7)
These bits are written by software to configure the corresponding I/O port.
Refer to Table 20: Port bit configuration table.
In input mode (MODE[1:0]=00):
00: Analog mode
01: Floating input (reset state)
10: Input with pull-up / pull-down
11: Reserved
In output mode (MODE[1:0] > 00):
00: General purpose output push-pull
01: General purpose output Open-drain
10: Alternate function output Push-pull
11: Alternate function output Open-drain
Bits 29:28, 25:24,
21:20, 17:16, 13:12,
9:8, 5:4, 1:0
MODEy[1:0]: Port x mode bits (y= 0 .. 7)
These bits are written by software to configure the corresponding I/O port.
Refer to Table 20: Port bit configuration table.
00: Input mode (reset state)
01: Output mode, max speed 10 MHz.
10: Output mode, max speed 2 MHz.
11: Output mode, max speed 50 MHz.

F030的定义是：

Bits 2y+1:2y MODERy[1:0]: Port x configuration bits (y = 0..15)
These bits are written by software to configure the I/O mode.
00: Input mode (reset state)
01: General purpose output mode
10: Alternate function mode
11: Analog mode

从中可以得知，两个片子的寄存器定义不同，所以配置当然也不同了。

再查询手册的UART RX定义，也有同样的不同。

再用兆易GD32F103替代STM32F103时，发现GD的定义与STM相同，但是MISO必须改为GPIO_MODE_AF_PP才能正常接收，否则SPI只能发送，接收错误。此处认为是GD的缺陷，待确认。